winees WP280013263 Spotlight Cam Instruction Manual
- June 12, 2024
- winees
Table of Contents
Winees Spotlight Cam
Model:
(NA) WP280013267
(EU) WP280013261
(UK) WP280013263
(JP) WP280013265
CAUTIONS
To avoid personal injury and/or possible product damage, the following cautions must be followed:
- Please use sorely the provided adapter instead of others in case of any damage to the product.
- Keep out of reach of children. This product contains small magnets and other small parts, which can cause choking or injury if ingested.
- To prevent early failure,the camera should only be installed in operating environments ranging between -20°C ~ 50°C(-4°F ~ 122°F).
- Do not install – close to heat source – near the metal objects and mirrors that cause radio signal attenuation or shading.
- Do not disassemble or reinstall the camera, otherwise it may cause security risks.
- Unplug the power cord before cleaning. Do not clean the camera with any liquids, spray cleaner or wet cloth.
- The slot and opening are used for ventilation, not allowed to be blocked or covered.
Introduction
Package Contents
Status LED Description
Status
|
Description
---|---
Solid Red| Power on/System booting / Factory reseting
Flashing Red| Wireless connection , cloud connecting fail
Solid Green| Wireless connected
Flashing Green| System ready for WiFi setup / Firmware update
Red and Green
flashing alternately| Unable to connect to the cloud
Set up Spotlight Cam in the AiDot App
- Scan the QR code below.
AiDot app is applicable for IOS 11.4 or higher, Android 6.0 or higher.
| 
---|---
Or search for“AiDot” in App Store or Google Play
-
Power on the camera, you will hear “Waiting for Wi-Fi configuration” with the camera’s indicator light flashing in green.
-
In the AiDot app, press ‘+’ – “devices”, select Winees Spotlight Cam, and follow the instructions on App.
-
Place the spotlight cam in the area where you plan to install to test the video quality, ensure that the camera can work normally after the final installation.
Install Spotlight Cam on the wall or celling
-
Placement
The recommended installation height is 2.5~3 meters (8.2~9 feet) above the ground. Either too high or too low height may affect the operation of the motion detector.
-
Install the bracket
When install the bracket on the wall/ceiling, please pay attention to the installation direction of the base.
If installing on a masonry surface, drill holes on the wall first, insert the anchor into the hole, and then install screw to fix the base.
If installing on a wooden surface, install screw to x the base directly.
Note: When install it upside down on the ceiling, you’ll need to set the image angle to 180° in the camera settings after adding the camera on the app.|
---|---
On the wall
|
Ceiling
-
3. Tighten the camera.
Arrange the cables behind the camera. You can route the wire from the top or bottom. Align the arrow on the camera base with that on the mounting bracket, snap it into place with a clear ”click” sound, and then tighten it with the Security Screw.
-
Adjust the camera angle
Manually adjust the up and down angle of the camera to obtain an accurate monitoring image and motion detect range. The tightness of the up and down rotation can be adjusted by the screw at the connection.
-
Power on the camera
Power on the camera and wait for the camera to work.
Requirements and Tech Specs
Wi-Fi Network Requirements
– Supports IEEE 802.11b/g/n
– Your Wi-Fi network broadcasts at 2.4GHz. 5GHz band is not supported
– Your network upload speed is suggested to be greater than 1 Mbps to
have fluent video streaming.
Power (Only for CE)
– 100~ 240VAC 50/60Hz power supply for the AC adapter
– DC 12V/1A input for the camera
– Max. power consumption: 10W
– Frequency range : 2412-2472MHz
– Maximum RF transmit power: 802.11b 16±2dBm, 802.11g 54M
14±2dBm, 802.11n HT20 12±2dBm, 802.11n HT40 12±2dBm
-Maximum radio-frequency power: 20 dBm
Camera
– 2K QHD @25 frames per second
– Maximum resolution: 2560*1440
– 1/3” Color CMOS sensor
– 135° (diagonal) wide angle lens
– Video compression: H.265/H.264
– Infra-red night vision: 10m(32.8ft)
– Motion detection: 7m Max.
– Rotation: 270° pan
Audio
– Built-in microphone and speaker
– Two-way talk
Lighting
– White light LED: 5000K, 400lm
Siren
– 100dB @10cm Max
Storage
– Micro SD card storage up to 128 GB (Micro SD card is not included)
Operating Environment
– Temperature: -20°C ~ 50°C(-4°F ~ 122°F)
– Humidity: ≤95% non-condensing
Trouble Shooting
If the default adding camera operation fails
-
Make sure your wireless router has the Internet access, and the Wi-Fi signal at the location where you install the camera is good.
-
Make sure the camera is plugged in and the status LED is on or flashing – Reset the camera if the LED is NOT flashing green. Then follow the App to add it.
-
Make sure the camera is not added to other user’s account. If it is, the owner of the camera has to unbind it First.
-
When this step is done, the camera should be added to your account.
If the Micro SD card is not detected by the camera -
Make sure the card is good and format it again in the FAT-32 format.
How to do the forced reset? -
If you cannot reset the camera from the setting page, please hold the reset button in the pin hole with the reset pin for 3 seconds and release. The camera will play a voice prompt” Restoring factory settings”. The time of the camera video stamp is not right
-
Please set the right time zone in the settings.
How long can a Micro SD card (not included) of dfferent capacity record?
| MicroSD card capacity | Duration of video recording |
|---|---|
| 16GB | 25h |
| 32GB | 50h |
| 64GB | 100h |
| 128GB | 200h |
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d’au moins 20 cm doit être maintenue entre l’antenne de cet appareil ettoutes les personnes.
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received,
including interference that may cause undesired operation.
Note: The grantee is not responsible for any changes or modifcations not
expressly approved by the party responsible for compliance. Such modifcations
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment of and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and your body.
Business name: APEX CE SPECIALISTS LIMITED
Business address: 89 Princess Street, Manchester, M1
4HT, UK
Email: info@apex-ce.com
Tel: +441616371080 Business name: APEX CE SPECIALISTS LIMITED
Business address: UNIT 3D NORTH POINT HOUSE, NORTH
POINT BUSINESS PARK, NEW MALLOW ROAD, CORK, T23 AT2P,
IRELAND
Email: info@apex-ce.com
Tel: +353212066339 Contact Us / Kontaktieren Sie uns
Linkzone Technology Co., Limited
ROOM 20 5/F WAYSON COMMERCIAL BLDG 28 CONNAUGHT
ROAD WEST SHEUNG WAN HK
Phone: 1-855-334-9800
Website: www.iwinees.com
Email: support@iwinees.com
Made in China Made in China
Documents / Resources
|
winees WP280013263 Spotlight
Cam
[pdf] Instruction Manual
WP280013267 NA, WP280013261 EU, WP280013263 UK, WP280013265 JP, WP280013263,
WP280013263 Spotlight Cam, Spotlight Cam, Cam
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>