JOBY JB01473 Impulse Bluetooth Remote Camera Control Instructions

JB01473 Impulse Bluetooth Remote Camera Control
Instructions
Model No.:1101473

Impulse

Upgrade your mobile photography and take the ultimate selfies. Trigger your phone’s camera from up to 90feet away with this universal remote for smartphones.

Battery

Requires one CR2032 battery (included).

Connect

Pairing for the first time

1. Turn ‘on’ Bluetooth on your device.
2. Press and hold the JOBY button until the LED light flashes.
3. Select ‘JOBY Shutter’ In Bluetooth settings.

Taking photos Open the camera app and press the JOBY button.
To turn off, press and hold the JOBY button until the LED light flashes.
Power will automatically shut off if idle for 10 minutes.
Deleting and re-pairing to a different device From off, press and hold the JOBY button for 2 seconds. Go to Bluetooth settings on your device and remove the ‘JOBY Shutter.’

WARNING!

Keep batteries out of reach of children. Swallowing may lead to serious injury or death in as little as 2 hours due to internal burns. If swallowed, go straight to a hospital emergency room. Dispose of used batteries immediately.

SAFETY INSTRUCTIONS

• Risk of explosion if the battery is replaced by an incorrect type.
• The included battery is not rechargeable.
• Please use the battery for its original purpose to avoid causing the battery to short circuit. When the conductive material is connected directly to the battery positive and negative will cause a shod circuit.
• Do not use a damaged battery.
• Keeping the battery in an extremely cold or very hot location can result in shortened battery life.
• When replacing the battery, please refer to the instruction manual and pay attention to the positive and negative direction of the battery
• Do not put the battery in the fire. Dispose of the battery according to local regulations.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the parts responsible for compliance could void the user’s authority to operate the equipment.
Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

**** Hereby, Vitec Imaging Solutions Spa declares that the Impulse radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following intemet address: joby.com/certification.

IC:24113-JB01473
Notice to Canadian users
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
   This device complies with RSS 247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.
   This Class B digital apparatus complies with Canadian ICES 003.

CCAK18LP2260T1
ER-R-021-JB01473

OFCA

Certified for use in Hong Kong
Certificate No.  HK021800166

COMMUNICATIONS AUTHORITY
SRRC CMIIT ID: 2018DJ7157
IMDA
Complies with IMDA Standards N3703-19
TRA
United Arab Emirates
TRA ID: DA73757/18
TA: ER65947/18

RoHS
Complies with the European Union’s “Restriction of Hazardous Substances Directive,” which protects the environment by restricting specific hazardous materials and products.

Vitec Imaging Solutions Spa
Via Valsugana 100 36022 Cassola (VI)
Italy ©2022 Vitec Holdings Italia Srl
1080575 – 01/22

Documents / Resources

| JOBY JB01473 Impulse Bluetooth Remote Camera Control [pdf] Instructions
JB01473 Impulse, Bluetooth Remote Camera Control, Remote Camera Control, Camera Control, JB01473 Impulse
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>