ONFORU BDB55G-3 PIR LED Wall Lights User Guide
- June 5, 2024
- ONFORU
Table of Contents
ONFORU BDB55G-3 PIR LED Wall Lights
COMPONENTS AND STRUCTURE
- Cover
- LED Light Source
- Lamp Bracket
- Sensor Head
PARTS LIST
SPECIFICATIONS
LED WALL LAMP
Model| BDB55G-3
Input Voltage| 220-240V～ 50Hz
Input Current| 0.25A
Rated Power| 55W
Useful luminous flux| 5000lm
CCT| 6500K
CRI| ** ≥80
Power factor| ≥0.9
L70B50 lifetime| 30000hours L70B50 @25°
Beam Angle| 120°
IP Rating| IP44
ta| -20-40°C
DIMENSIONS**
Model| BDB55G-3
DIMENSIONS| 272x123x121mm
Weight| 0.98 KG
Max Projected Area| 0.0214 m²
Max. Lighting Coverage| 90 m²
Note
The testing standard of the product’s luminous flux: Place the three/two
lights on the same horizontal surface for testing, and the tested luminous
flux is the accurate luminous flux.|
Operation Instructions
LUX: Change the Working Mode.
Sun Mode: works all day long.
Moon Mode: works only when it is dark (night time).
Please note: If your light can not be turned off after people leave,
please switch the button counter-clockwise from Sun Mode to Moon Mode.
TIME: Change the Illumination Time.
After motion is sensed, the light will be on immediately. Switch the button
counter-clockwise to prolong the illumination time from 10s to 180s
approximately.
Delay Time: the time that the light will be on after people leave.
SENS: Change the Sensitivity.
Switch the button counter-clockwise to adjust or tune the sensing distance
from the Min. to Max.(Max. Sensing Range 39ft / 12M).
PREPARATION
Check all components for damage, do not use the product if it is damaged.
SAFETY INFORMATION
Disconnect the power supply before attempting any work on the unit!
Installing these units involves work on the mains voltage supply; installation
must therefore be carried out professionally In accordance with the appliance
national wiring regulations
And electrical operating conditions.
Be careful not to damage or cut the wire insulation (Covering) during
installation. Do not let the wires touch any sharp edges.
INSTALLATION STEPS
Product appearance may vary from image shown 
INSTALLATION STEPS
NOTE: The raised part (RA) of the metal plate must be engaged with the recessed part (RE) of the base, otherwise it cannot be installed.
Wire connection
-
Blue
Neutral line -
Brown
Live wire -
Yellow-green
Ground wire
Troubleshooting
| Malfunction | Cause | Remedy |
|---|---|---|
| LED senses a movement, the light does not light up |
- The light is not energized
- Other surrounding light sources make the light misjudge it as daytime
- During the day, the brightness is in night mode
- Internal wiring is loose
|
- Check power-on status
- Turn off the nearby lights or sensor head to other directions
- Reset
- Rewiring after power failure
LED sensor light did not go out, continued to light up| Continuous movement
within the sensing range| Check the relevant area and retune or override the
sensor head if necessary
LED sensor light illuminates during the day| The shadows around the sensor
make it mistakenly think it’s night|
- Do not cover the sensor head
- Place the light in a place where the light is bright enough during the day
LED sensor light flashing| Surrounded by other unstable light sources shining
onto the induction| Avoid being exposed to such light sources
LED lights turn on unexpectedly|
- Wind blows the branches and bushes within the sensing range
- Sensing cars on the road
- Sudden temperature change due to climate factors or fans, exhaust from open windows
|
- Adjust its scope
- Adjust its scope
- Change irradiation area
Manufacturer
Shen Zhen Shi Meng Zhi Tuo Ke Ji You Xian Gong Si
Address: qian wan yi lu 1 hao A dong 201 shi qian hai shen gang he zuo qu Shen
Zhen, Guang
Dong, 518000, CN
support@onforuled.com
www.onforuleds.com
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom | support@onforuled.com
EU REP MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos
Nicosia, Cyprus | support@onforuled.com
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>