HOSELINK L450 4m Solar LED Strip Light User Manual

June 5, 2024
HOSELINK

User Manual
MODEL: L450
Solar LED Strip Light | Warm White |
4m | Adhesive | ASPECT

With its adhesive backing, Hoselink’s Solar LED Strip Light is the perfect accent for your deck, entertaining area, balcony or for lighting the underside of stairs and fences.

LIGHTING MODES

The Solar LED Strip Light has 4 lighting modes:

1 Constant light
2 Slow flash| 3 Quick flash
4 Pulsating light
---|---

PRODUCT INSTALLATION

Installing the solar panel
STEP ONE: Find a suitable location
While the strip light may run along the underside of a deck or staircase, the solar panel will need access to direct sunlight to charge. For optimum results, charge for 6-8 hours per day. Make sure you have enough cable length to reach between the solar panel and strip lights.

STEP TWO: Assemble the ground spike
Slot the ground spike into the tube on the back of the solar panel, then push the spike into the ground.

To mount the solar panel to a wall or fence, follow these steps:

STEP ONE:
Mark out holes with a marker pen.

STEP TWO:
Using a 6mm drill piece for masonry installation, drill two holes.

STEP THREE:
Gently hammer the plugs into place and then secure the base of the solar panel by tightly screwing in the supplied screws.

FOR TIMBER:
Drill two 3mm pilot holes to guide the screws into place (plastic plugs are not required). Secure the base of the panel using the supplied screws.

INSTALLING THE LIGHTS

STEP ONE: Unspool the strip light from the roll
We recommend unspooling the full length and laying it out along where it will be installed.

STEP TWO: Remove the protective tape
Work your way along in sections. Carefully peel back the tape, protecting the glue strip (refer to image A). Once exposed, make sure the glue strip does not come into contact with anything other than the desired surface. The glue is very strong, and it can be hard to remove the lights if stuck in the wrong place.

STEP THREE: Install Lights
Make sure the strip is flat and even, and press the solar strip lights into place. Hold them down for 4-5 seconds to ensure the glue sets. Then, run your thumb or fingers along the section of lights to remove any bumps or unevenness. Repeat steps 2 and 3 until the entire length of lights is installed.

STEP FOUR: Turn on the light
Use the ‘ON/OFF’ button located on the back of the solar panel to turn the lights on. Press the ‘MODE’ button to select the desired light setting. The solar panel has a built-in intelligent light sensor, which detects darkness, automatically illuminating at dusk and turning off at dawn.

REMOVING THE LIGHTS

Please note that once the lights are installed, they cannot be moved. The glue strip is intended for single use and removing the lights will damage it.

STEP ONE:
Carefully peel the light strip away from the surface. It is normal for the glue strip to come away in sections or leave parts behind on the mounting surface. Do not rip lights away from the surface as the glue is quite strong and this may cause damage to the underlying surface.

STEP TWO:
Once the entire strip light is removed, work back along the surface and remove any remaining sections of glue. These should peel off.

Specifications

Solar panel Monocrystalline Silicon
Lithium battery 3.7v 1800mAh
Operating time 8 hours
Charge time 8 hours
Strip length 4m
Cable length from panel to strip 2m
Light temperature (Kelvins) 3000k
LED lumens 240 Lumens
Number of LEDs 200

WARNING: DO NOT USE THIS LIGHT UNDERWATER OR IN LOW-LYING PUDDLES

For more information visit hoselink.com.au
or call
1300 900 617
Cultivating Connections
youtube.com/hoselink 

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals