Enping FV-1003 Wireless Microphone User Manual

Enping FV-1003 Wireless Microphone

FAQs

• Q: How do I replace the batteries in the transmitter?
  • A: To replace batteries, follow these steps: 1. Open the battery compartment cover. 2. Install 2PCS AA batteries correctly. 3. Close the battery compartment cover securely.
• Q: What should I do if the LED indicator of the microphone is not lighting up?
  • A: If the LED indicator is dark, please check and replace the batteries in the microphone. Ensure proper battery installation and contact.

Thanks for your support and trust to purchase our good quality wireless microphone. Please read this operation manual in detail to understand how to operate this product properly.

Product Features

• Using VHF 174.2-215.2 MHz frequency to avoid the interference.
• Using multilevel high-frequency and middle-frequency narrowband filters, to dispel any possible interference signals.
• With the low-consumption components, the life of the battery will be much longer.
• With the power indication circuit in the handheld microphone, so you will know when to replace the battery.
• All use quartz crystal oscillating circuits, so the frequency is very steady.
• With the decreasing back-out whistle function, it can decrease the whistle efficiency.
• The tonality is quite good with the excellent crystal and components.

Introduction of the Receiver

• 1. ON/OFF Power Switch
• 2. 6. Volume Control Knob
• 3. AF LED indicator
• 4. Power LED indicator
• 5. RF LED indicator
• 7. 8 Antenna
• 9. Power input
• 10. 1/4” (6.35mm) Audio input

Introduction of the Transmitter:

1. Grill: To protect the capsule of the microphone.
2. Microphone Body
3. LED indicator
4. ON/OFF switch
5. Battery compartment: on the back side of the microphone

Operation of the receiver

1. Connect the power adapter with the Power input ⑨. Then Plug the power adapter into a power socket.
2. Use the Audio Cable to connect the receiver 1/4” output ⑩ and 1/4” input of a mixer or active speaker.
3. Pull out antenna A & B ⑦ ⑧, and make it vertically.
4. Turn ON the ON/OFF power switch ① and the power LED indicator ④ is lit.
5. When turning on the microphone, the receiver RF LED indicator ⑤ is lit.
6. The sound volume could be adjusted by the volume control knobs ② ⑥.
7. Please unplug the power adapter if you don’t use it for a long time.

Operation of the transmitter:

1. Open the battery compartment cover ⑤, install 2PCS AA batteries correctly, and then cover it.
2. Turn ON the ON/OFF switch ④ when using, the LED indicator ③ is lit.
3. If the LED indicator ③ of the microphone is dark, please replace the batteries.
4. Please take out the batteries if you don’t use the transmitter for a long time.

Technical Specifications

• Frequency Range: VHF 174.2-215.2 MHz
• Modulation Mode: FM
• Pickup/Polar Pattern: Uni-Directional
• Impedance: 600 Ohms ± 30%
• Frequency Response: 60-13KHz
• Frequency Stability: ±30ppm
• Dynamic Range: ＞80dB
• T.H.D: ≤1%
• S/N Rate: ＞70dB
• Sensitivity: 30dB/uV
• Audio output: ＞25mV
• Output power: <10 mW
• Receiver Power Adapter: AC 90-240V,50Hz-60Hz, DC 12V
• Transmitter Power Supply: 2 x AA battery
• Wireless Range: up to 30m

Problem Shooting

1. The power LED indicator light is not lit when turning on the receiver power switch.| The receiver is without a power supply.| Connect the power adapter correctly.
2. No sound| Wireless microphones do not turn “ON”| Turn ON the power switch.
Didn’t connect the Audio Cable.| Connect the audio cable correctly.
Didn’t turn on the volume.| Turn on the volume control knob.
The distance between the wireless microphone and the receiver is too far.| Go close to the receiver.
3. Receiving distance is too short| The antenna of the receiver is not pulled out| Pull out the antenna
Low battery energy.| Replace batteries.
4. The sound becomes worse.| Low battery energy.| Replace batteries.
Other interference signal.| Check if other equipment is causing interference.

If it is not working normally after checking by yourself, Please contact the seller or our agent. Please do not repair it by yourself.

Caution:

1. The receiver should not be placed at the dead corner to keep good signal condition.
2. Please don’t drop the microphone to avoid damage.
3. This system should avoid direct sunlight/ liquid and do not close to a microwave.
4. Please don’t disassemble by yourself because it may cause electric shock.

What’s in the box

1. Receiver: 1 PC
2. Transmitter: 2 PCS
3. Power Adapter: 1 PC
4. Audio Cable: 1 PC
5. AA battery: 4 PCS

FCC

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning for Portable device: The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>