SpeedyBee F7 V3 BL32 50A 30×30 Stack Mini Flight Controller User Manual

SpeedyBee F7 V3 BL32 50A 30×30 Stack Mini Flight Controller

Overview

Specs Overview

Product Name

|

SpeedyBee F7 V3 BL32 50A 30×30 Stack

---|---

Flight Controller

|

SpeedyBee F7 V3

ESC

|

SpeedyBee BL32 50A 4-in-1 ESC

Bluetooth

|

Supported. For FC & ESC parameter setting

Wireless FC Firmware Flashing

|

Supported

Wireless Blackbox Download

|

Supported

Power Input

|

3-6S LiPo

Mounting

| 30.5 x 30.5mm（4mm hole size ）

Dimension

|

45.6mm(L) x 40mm(W) x 16.1mm(H)

Weight

|

29.9g

Dimensions

Package

1. SpeedyBee F7 V3 Flight Controller x 1
2. SpeedyBee BL32 50A 4-in-1 ESC x 1
3. DJI 6pin Cable(80mm) x 1
4. SH 1.0mm 15mm-length 8pin Cable(for FC-ESC connection) x 1
5. M3*8mm Silicone Grommets(for FC) x 5
6. M3*8.1mm Silicone Grommets(for ESC) x 5
7. M3*30mm Iner-hexagon Screws x 5
8. M3 silicone O Ring x 5
9. M3 Nylon Nut x 5
10. 35V 1500uF Low ESR Capacitor x 1
11. XT60 Power Cable(70mm) x 1
    • 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable(30mm) x 1
    • 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable(60mm) x 1
    • 4pin SH1.0 to 4pin JST1.25 FPV Cam Cable(60mm) x 1
    • 4pin SH1.0 Radio Receiver Cable(100mm) x 1
    • 4pin SH1.0 to 4pin SH1.0 Analog VTX Cable x 1
    • 6pin SH1.0 GPS Module Cable without Connector on another end(100mm) x 1
    • 6pin SH1.0 GPS Module Cable Connector of another end x 1

FC & ESC Connection

Method 1 – Direct Soldering

Method 2 – All connectors

SpeedyBee F7 V3 Flight Controller

Layout

• LED Indicator Definition

• RED LED – Power Indicator.Solid Red aer powering up.

• GREEN LED – Bluetooth status light. Solid Green indicates Bluetooth is connected.

• BLUE LED – Flight controller status light which is controlled by the flight controller firmware.

• Orange LED – LED Control Mode Indicator. It indicates the 4 sets of LEDs connected to LED1-LED4 connectors on the bottom side are controlled by Betaflight firmware(BF_LED mode) or the Bluetooth Chip(SB_LED mode).

• Solid Orange: indicates the 4 x LEDs are in SB_LED mode. In this mode, when the FC is powered on and in standby mode, press the BOOT button to cycle the display modes of the LEDs.
  You could also change modes in the app wirelessly.

• OFF: indicates the 4 x LEDs are controlled by Betaflight firmware. Long press the button for 3 seconds to switch the control modes between BF_LED mode and SB_LED mode.

FC’s Peripheral Connection

Wiring Diagram

Method 1 – Direct Soldering

Method 2 – All connectors
To recognize the wires in the package better, we marked some of these wires with letters(from A to F). Please find the right wires accroding to their letters.

App

• Get the SpeedyBee App
  Search ‘SpeedyBee’ on Google Play or App Store. Or download the Android .apk file on our website: https://www.speedybee.com/download

• Connect the App

FC Firmware Update

Specifications

SpeedyBee BL32 50A 4-in-1 ESC

Layout

Connection with Motors & Power Cable

Note: In order to prevent the stack from being burnt out instantaneous voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.

ESC Conifguration & Firmware Update

• This ESC is a 32-bit ESC running BLHeli32 firmware inside. Since the BLHeli32 is close-sourced. So ESC configuration & firmware update can be done wirelessly in the SpeedyBee app. Please download the lastest BLHeliSuit32 configurator to setup your ESC at https://github.com/bitdump/BLHeli/releases.
• Even so, you could still change motor directions in the app for this ESC. Please connect to the app, go to Motors page, click the button shown below. Then experience the easiest and coolest way to change motor directions.

Specifications

References

• Releases · bitdump/BLHeli · GitHub
• Releases · bitdump/BLHeli · GitHub
• download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>