SpeedyBee BLS 50A 30×30 Stack User Manual

June 4, 2024
SpeedyBee

F405 V3 30×30
BLS 50A
F405 V3 BLS 50A 30×30 Stack
User Manual V1.0

Part 1 – Overview

Specs Overview

Product Name SpeedyBee F405 V3 BLS 50A 30×30 Stack
Flight Controller SpeedyBee F405 V3
ESC SpeedyBee BLS 50A 4-in-1 ESC
Bluetooth Supported. For FC & ESC parameter settings
Wireless FC Firmware Flashing NOT Supported
Wireless Blackbox Dwonload & Analysis NOT Supported
Power Input 3-6S LiPo
Mounting 30.5 x 30.5mm (4mm hole size )
Dimension 45.6mm(L) x 44mm(W) x 18.3mm(H)
Weight 23.4g

Dimensions

SpeedyBee BLS 50A 30x30 Stack

Package

Option 1 – SpeedyBee F405 V3 50A 30×30 Stack

SpeedyBee BLS 50A 30x30 Stack - FIG

  1. SpeedyBee F405 V3 Flight Controller x 1
  2. SpeedyBee BLS 50A 4-in-1 ESC x 1
  3. 35V 1500uF Low ESR Capacitor x 1
  4. M3 Nylon Nut x 5
  5. M3 silicone O Ring x 5
  6. M3*8mm Silicone Grommets(for FC) x 5
  7. M3*8.1mm Silicone Grommets(for ESC) x 5
  8. SH 1.0mm 15mm-length 8pin Cable(for FC-ESC connection) x 1
  9. M3*30mm Iner-hexagon Screws x 5
  10. DJI 6pin Cable(80mm) x 1
  11. XT60 Power Cable(70mm) x 1

Option 2 – SpeedyBee F405 V3 Flight Controller

SpeedyBee BLS 50A 30x30 Stack - Controller

  1. SpeedyBee F405 V3 Flight Controller x 1
  2. M3*8mm Silicone Grommets(for FC) x 5
  3. SH 1.0mm 30mm-length 8pin Cable(for FC-ESC connection) x 1
  4. DJI 6pin Cable(80mm) x 1

Option 3 – SpeedyBee BLS 50A 4-in-1 ESC

  1. SpeedyBee BLS 50A 30x30 Stack - Controller 1 SpeedyBee BLS 50A 4-in-1 ESC x 1
  2. 35V 1500uF Low ESR Capacitor x 1
  3. M3 silicone O Ring x 5
  4. XT60 Power Cable(70mm) x 1
  5. SH 1.0mm 30mm-length 8pin Cable(for FC-ESC connection) x 1
  6. M3*8.1mm Silicone Grommets(for ESC) x 5

FC & ESC Connection

Use the 8-pin cable in the package to connect the FC and the ESCOr solder 8 wires directly to the 8 pads on each end.
Method 1 – Using 8-pin cable
Use any end of the 8-pin JST cable to connect the FC to the ESC.SpeedyBee
BLS 50A 30x30 Stack - F7 V3 Flight Controller

Method 2 – Direct soldering
Solder 8 wires to the 8 pads on each end referring to the pad definition below.SpeedyBee BLS 50A 30x30 Stack - Flight

Part 2 – F405 V3 Flight Controller

Layout

SpeedyBee BLS 50A 30x30 Stack - FPV CamSpeedyBee
BLS 50A 30x30 Stack - LED1

LED Indicator Definition
RED LED – Power Indicator.Solid Red after powering up.
GREEN LED – Bluetooth status light. Solid Green indicates Bluetooth is connected.
BLUE LED – Flight controller status light which is controlled by the flight controller firmware.
Long press the button for 3 seconds to switch the control modes between BF_LED mode and SB_LED mode.
Orange LED – LED Control Mode Indicator. It indicates the 4 sets of LED strips connected to LED1-LED4 pads on the corners of the flight controller are controlled by Betaflight firmware(BF_LED mode) or the Bluetooth chip(SB_LED mode).
Solid Orange: indicates the 4 x LEDs are in SB_LED mode. In this mode, when the FC is powered on and in standby mode, press the BOOT button to cycle the display modes of the LEDs. You could also change modes in the app wirelessly.
OFF: indicates the 4 x LEDs are controlled by Betaflight firmware.

BOOT Button

[A]Only if the flight controller gets bricked and can’t power up, please follow these steps to re-flash firmware for it:

  1. Insert a USB A to TYPE-C cable to your PC.
  2. Press and hold the BOOT button, insert the USB cable into the flight controller, then release the BOOT button.
  3. Open Betaflight/Emuflight/INAV configurator on the PC, go to the ‘Firmware Flashing’ page, choose the target ‘SPEEDYBEEF405V3’ and flash.
    [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 pads on the corners. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the
    BOOT button to switch between SpeedyBee-LED mode and BF-LED mode.
    Under BF-LED mode, all the LED1-LED4 strips will be controlled by the Betaflight firmware.

FC’s Peripheral Connection

SpeedyBee BLS 50A 30x30 Stack - Peripheral.

App & FC Configuration

Get the SpeedyBee App
Search ‘SpeedyBee’ on Google Play or App Store. Or download the Android .apk file on our website: https://www.speedybee.com/download.

FC ConfigurationSpeedyBee BLS 50A 30x30 Stack -
Configuration

FC Firmware Update

SpeedyBee F405 V3 flight controller does not support wireless firmware flashing, so please flash firmware for it on your PC following the steps below:

  1. Connect the flight controller to the PC with a USB cable
  2. Open Betafight/Emuflight/INAV configurator on your PC. Take the Betaflight configurator as an example, go to the ‘Firmware Flashing’ page, choose the target ‘SPEEDYBEEF405V3’ and flash.

SpeedyBee BLS 50A 30x30 Stack - configurator

Specifications

Product Name F405 V3 30×30 Flight Controller
MCU STM32F405
IMU(Gyro)  BMI270
SB Port Type Type-C
barometer  Built-in
SD Chip AT7458E chip
BLE Bluetooth Supported. Used for Flight Controller configuration
DJI Air Unit Connection Way Two ways supported: 8-pin connector or direct

soldering.
Blackbox MicroSD Card Slot| Supported. Please use d4G8 SOSC/SONC microS0 card and : timid be formatted to
FAT I tICAT32 format DWI use SOXC cards. Note: Beta,’ light can only recognize 4GB max.
lit etaFlight Camera Control Pad| Yes(CC pad on the front side)
Current Sensor Input| Supported. For SpeeclyBee BLS 50A ESC, please set scale a 3813 and Offset a O. ,
Power Input| 35 -8S Lipa(Through G. BAT pin from the 8-pin connector or 8-pads on the
bottom side)
 Output|  9 groups el 5V output. four ..5V pads and 1 BZ• pad( used for Buzzer) on front side. and 4x LED 5V pads. The total current bad is 2k
 Output| 2 groups of 9V output. one .9V pod on front We and other included in a connector on bottom side. The total currant load is 2A
3V Output|  Supported. Designed for 3.3V-Mput receivers. Up to 5CCrm current bad.
IP 4 5V Output| Supported. Desgned for receiver and GPS module even when the FC rs privet –
through the USG port Up to IA current load.
ESC Signal| MI – M4 on bottom side and M5-M8 on front wle.
UART| S sets(UARTI.UARTZ UART3. UART4(For ESC Telemetry). LIMITS)
ESC Telemetry UART| R4(UART4)
112C| Supported. SDA & SCL pads on halt side. Used for the magnetometer. sonar. etc-
Traotonal Betafight LEO Pad| ,’ Supported. 5V. G and LED pads cn bottom of the front side. Used for WS2812 LED
controlled by Betafight firmware.
‘turret| EtZ• and B2- pad used for 5V Buzzer II
BOOT Button| Supported.
(A). Press and hold the BOOT button and power the FC on at the same tine me force the
FC to enter DFU mode. this is for firmware flashing when the FC gets bricked.
(B). When the FC is powered on and m standby made. the BOOT button can be used to corn:oder the LED strips connected to LECI1-LE04 connectors on the bottom We. By default short-press the BOOT button to cycle the LED displaying made. Long-press the BOOT button to switch between SpeedyBee-LED mode and OF-LED made. Under BF-LED made. all the LED1-LED4 strips WA be =tolled by BetafIght firmware.
Input ‘| Supported. Named as RS on the front side.
: Miniport “| , Use any TX pod of UART for the SmartPort feature.
Supported Flight Controller Firmware| BetaFlight(Default). EMUFfight.INAV
firmware Target Name|  SPEEDYBEEF405V3
Lumina ‘| 30,5 x 30.5rnm( amen hale diameter)
: Mensal ‘| 41.114)x 39.4(W) x 7.8(H)mm
Weight| 9.6g

Part 3 – SpeedyBee BLS 50A 4-in-1 ESC
Layout
SpeedyBee BLS 50A 30x30 Stack - Controller SF

Connection with Motors & Power Cable

Note: In order to prevent the stack from being burnt out by voltage spikes on powering up, it is strongly recommended to use the Low ESR capacitor in the package.

ESC Configuration

SpeedyBee BLS 50A 30x30 Stack - Configuration1

  • If you’d like to use a PC configurator, we recommend the ESC Configurator.

ESC Firmware Update

  • We recommend using the ESC Configurator on your PC to update firmware for this ESC. Please make sure to select ‘JH-50’ as the ESC type for either BLHeli_S or Bluejay.

Specifications

Product Name SpeedyBee BLS 50A 30×30 4-in-1 ESC
Firmware BLHeli_S JH50
Wireless Configuration Full Configuration Supported in the SpeedyBee app
PC Configurator Download Link https://esc-configurator.com/
Continuous Current 50A * 4
Burst Current 55A(5S)
TVS Protective diode Yes
External Capacitor 1500uF Low ESR Capacitor(In the package)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT
Current Sensor Support (Scale=386 Offset=0)
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 45.6(L) 44(W) 6.1mm(H)
Weight 13.8g

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals