Ciro3D G0058042 Passenger Phone Mount for Harley Davidson Instruction Manual
- June 5, 2024
- Ciro3D
Table of Contents
Ciro3D G0058042 Passenger Phone Mount for Harley Davidson
WARNING This indication alerts you to the fact that ignoring the contents
described herein can result in potential serious injury or death if not
followed.
CAUTION This indication alerts you to the fact that ignoring the
contents described herein can or will result in material damage and/or
personal injury.
ATTENTION This indication alerts you to the fact if you ignore this
detail you will affect the performance or functionality of the product.
All Ciro products are designed for “easy assembly” and/or “plug and play”. We
recommend a competent mechanic install our products, using standard mechanical
procedures to assure a safe and successful installation. Read completely and
understand the instructions prior to starting installation.
NOTE: Ciro products are designed and manufactured under very strict quality
control. Ciro warrants that products sold to the original purchaser shall be
free from any defects in materials and workmanship for a period of 3 (three)
years from the date of purchase, and a limited lifetime warranty against LED
failure. Ciro will have no obligation if the customer cannot show proof of
purchase. Warranty will not be granted unless the part is properly installed,
unmodified and maintained. Ciro will not be liable for any consequential and
incidental damages, including labor, or non-Ciro products. Please visit
Ciro3d.com for our complete warranty policy.
Included Items:
| 1 | Phone mount arm | 2 | Plastic flat washer | 1 | 1/4-20 Nylon locknut |
|---|---|---|---|---|---|
| 1 | Phone mount base | 1 | Metal washer | 2 | #10-32 Screw |
| 1 | Accessory Mount | 1 | 1/4-20 Carriage bolt | 1 | Shrink tubing |
Installation Instructions:
-
Park on a level surface, allow the motorcycle to cool.
-
Determine which side of the motorcycle you wish to install the Passenger Phone Mount.
-
The base is directional and needs to point away from the motorcycle when the Passenger Phone Mount is installed, Fig.4. Attach the mount base to the top of the accessory mount using the two supplied #10-32 screws, Fig.2. The two tabs of the accessory mount point down, Fig.3.
-
Cut the shrink tubing to cover the joining surfaces of the accessory mount and mount base, Fig.2. Slide the shrink tubing over the joint and apply heat to conform.
-
Assemble the mount arm on top of the mount base. Insert the carriage bolt through the arm, put a plastic washer between the arm and base, followed by the other plastic washer, then the metal washer and locknut. Order shown in Fig.1.
-
Tighten locknut so the arm has some friction when pivoting. Assembly should be tight enough to not move when in use but still allow for passenger adjustments if necessary.
Note: Periodically check tightness of hardware to maintain adequate friction. -
Open the Tour-Pak®, remove the liner. On the side that you’ve chosen to install the Passenger Phone Mount, loosen the three speaker screws, Fig.5. Loosen the top screw a bit more than the lower two, do not remove the screws.
-
Pull the top of the speaker away from the Tour-Pak, creating a gap between them wide enough for the accessory mount to fit between them and exposing the top speaker screw, Fig.6.
-
Slide the accessory mount between the Tour-Pak® and speaker, straddling the top speaker screw between the two tabs of the accessory mount. The Passenger Phone Mount should be resting on top of the speaker, Fig.7.
-
Tighten the three speaker screws. While tightening the screws, put pressure on the back of the Passenger Phone Mount so that it seats properly when fully tightened.
-
Reinstall the Tour-Pak® liner.
-
Install phone holder following its provided instructions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>