Broadway V24MCE Lifestyle User Manual

Broadway V24MCE Lifestyle

IMPORTANT SAFEGUARDS

1. Only for use in dry rooms. The device must not be operated in wet rooms, areas with high humidity, greenhouses, or similar localities.
2. Do not place the appliance near a bathtub, swimming pool, sink, or similar water bodies. The appliance never immerses in water or other liquids!
3. Verify that the specified on the nameplate with your house wiring matches.
4. The socket must approved, properly installed, and in good working order.
5. The socket must be accessible at all times to enable quick removal of the power plug.
6. The device may not be operated directly under a main socket.
7. If possible, use no multiple outlets or extension cords. If this is unavoidable, the power strip or extension cord must comply with local regulations. The technical data of the power strip or extension cord must match the data listed on the nameplate of this device.
8. Attention! The device should not be operated unattended. It must also not be connected via a timer switch to the power supply.
9. To avoid danger, the device may not be powered by an external voltage control (for example, a dimmer, speed control, or the like).
10. This appliance is not intended to be used with a lack of experience and/or knowledge by persons (including children). Unless they are supervised or receive instructions about how to use the device to by persons responsible for their safety. The appliance must be kept out of reach of children and if the device is used must be located in the vicinity, children are supervised to avoid that these include the device in their play.
11. Operate not in use in flammable atmospheres (for example, in the presence of flammable gases or spray cans)! Explosion and fire hazard!
12. Do not store any flammable liquids, paints, gas containers, or the like near the device.
13. Caution! Do not insert foreign objects into the ventilation slots! Risk of injury from electrical shock and possible damage to the unit!
14. Always ensure that the power cable free from pressure.
15. The cable must always be completely unrolled and may not be wrapped around the device.
16. Make sure that the power line does not run over sharp edges and does not come into contact with hot surfaces.
17. Keep the device clean. This is to prevent fire and other hazards.
18. Always keep the device unrestricted intake and can blow! Do not cover the ventilation slots apply foil, blankets, mats, or the like. Keep clean vents.
19. The installation surface must be dry, flat, non-slip, and sufficiently stable. Place the device on an unstable surface will cause an accident! Make sure that nobody can trip over the power cord in case an accident occurs.
20. The appliance must never be cleaned with water spray, steam cleaners, or the like!
21. Never pull on the cable plug from the socket! Always grip the plug and pull to disconnect.
22. Never move by pulling the cable and never use the cable for carrying purposes!
23. Never try to repair the appliance yourself. If a repair is necessary, please contact our service center, its service agent, or a similarly qualified operation.
24. The device is not approved for commercial or industrial use.
25. This product can only be used according to the specifications indicated on the identification plate and in the instruction manual. Any other use of the device as described can lead to hazards such as short circuits, fire, etc. It is not allowed to modify this product in any way or to open the case, otherwise the product no longer meets the requirements of its safety class.
26. Before each use, check the unit, including the cable and the components for defects that could impair the functional reliability of the device. If the device or the supply of an unacceptable use, such asana overload has been suspended or has been improperly used, can be present from the outside invisible damages. In this case, the device does not operate. Let the device for inspected or repaired by the dealer or his service.
27. Always unplug the power cord before refilling the water, cleaning, or moving.
28. Unplug the power plug when the appliance is not in use.
29. Do not overfill the water tank.
30. To avoid any possible hazard, the device should avoid splashing water when the tank is full.
31. Never use the device in lateral or supine.
32. Do not shake or break the unit.
33. For Safety cleaning and hygiene see the section Cleaning.
34. The external flexible cable of this appliance cannot be replaced. If the supply cord or plug is damaged, the device must no longer be used and should be discarded.
35. Remove the batteries from the remote control when a long time is not used.
36. The water level must be between the MIN and MAX lines.
37. Do not use the unit for other than its intended use.
38. This appliance is intended for household and indoor use only.

PRODUCT FEATURES

• Mosquito Light Trap
  This mosquito light trap employs UV-LED lights, which will generate the wave in 395nm length. It will induce the mosquitoes to get close to the light and the airflow will absorb them quickly into the mosquito reserving chamber. After the dehydration process, mosquitoes are killed ba a physical way, without toxicity, smoke, sm, ell, or radiation. It’s safe and suitable for home and office use.

• Cool
  It cycles the water to blow cool air. It can lower the surrounding temperature and provide you with a comfortable environment in the hot summer.

• ionizer
  It releases negative ions to freshen the air and care for health.

• Detachable filtration mesh
  It is easy to clean. The filter removes harmful tiny substances, such as dust and pollen.

• Energy saving, high-efficiency, friendly environment

• Wide range of air output 100 degree angle wide range of air output. 3 fan speeds: HIGH-MID-LOW

• Remote Control
  6 meters remote control, 120-degree angle wide range receiver

• Beep sound reminder
  It has a beep-sound reminder function, convenient to use.

• Memory function

TECHNICAL PARAMETERS

Note : Due to the constant development of our products regarding specification and design, we take reservations for changes without prior notice.

OPERATION INSTRUCTION

1. Pull the unit outwards from the carton and place it on a solid hot-proof horizontal surface.

2. Check if the accessories are complete, same as the accessories list.

3. Place the unit on a solid hot-proof horizontal surface. Take out the casters and caster wrench to assemble.
   Note : Casters with skid are for the two front holes and casters without skid are for the two back holes at the bottom of the unit. (Shown as figure.1)

4. Add water : Pull upwards the water tank and pull outwards about 10cm to the locking pin, then add water. (Shown as figure.2)
   Note:

5. The water level must be between the MIN and MAX lines. (Shown in Fig. 3)

6. After some time of operation, dust and dirt may occur in water tank. It is recommended to change water and clean water tank frequently.

7. Only use the unit with correct AC outlet.

8. Insert the plug pin into a wall socket and turn on the power switch which is at the side of the unit. A small beep sound can be heard and the power indicator will be on.

Note :

1. To protect against electric shock, do not remove plug from wall outlet by wet hand.
2. Unplug from outlet while moving the unit.
3. Insert the plug pin into the wall socket and make sure it is connected well.

CONTROL PANEL OPERATION INSTRUCTION

Insert the plug pin into a wall socket and turn on the power switch which is at the side of the unit. A small beep sound can be heard and the power indicator will be on.

• POWER : Press once this button to make the unit ready for work. It will start up with MID in 3 seconds and then revert to work under the memorized status. If for first-time use, it will start up with MID in 3 seconds and then work with LOW. Press again this button to turn it OFF.
• SPEED: Press this button to select the desired fan speed LOW MID HIGH LOW , in turn.
• SLEEP MODE: Press this button to select the desired wind mode, it works as per the preset computer program, alternating between different fan speeds.
• UP/DOWN: Press this button to make a vertical swing of louvers, and the indicator will be displayed. Press again for a fixed air direction.
• LEFT/RIGHT: Press this button to make horizontal swing lovers, and the indicator will be displayed. Press again for a fixed air direction.
• COOL: Press once this button to start the evaporative cooling function. Press again this button to cancel.
• TIMER : It can be set between 0.5 to 8 hours, increased by 0.5-hour intervals. When the digital display shows 8 hours, press again this button to cancel.
• ECO: Press this button to light off the LED monitor, and press it one more time to light up again.
• ION : Press once this button to release negative ions into the air, to freshen the air and care for health. Press again this button to cancel.
• MOSQUITO LIGHT MODE: Press this button to turn on the mosquito light trap and kill the mosquitos. Press again this button to cancel.

MAINTENANCE AND CLEANING

Note :

• Unplug from the outlet.
• No water on the control panel.

Cleaning the filtration mesh

1. Remove the plug from the wall outlet.
2. Catch the filtration mesh handle and pull it upwards. (shown in Fig. 4)
3. Clean filtration mesh with mild detergent and soft brush.
4. Make sure the filtration mesh is completely dry before installing.

Note: After long time of operation, the filtration mesh becomes clogged with dust and dirt, which will greatly affect the unit’s performance. It is recommended to clean the filtration mesh frequently.

Cleaning the water tank

1. Remove the plug from the wall outlet.
2. Pull out the water tank.(shown as fig.5)
3. Clean the water tank with a little mild detergent on a towel and then rinse in water.
4. Put the water tank in place after cleaning.

Note: After some time of operation, dust and dirt may occur in the water tank. It is recommended to change water and clean water tanks frequently.

After cleaning the water tank, please see the location of the water pump before pushing the tank into the cooler. If you find the pump is placed below the top surface of the water tank( shown as Fig. 6), you shall lift it above the top surface of the water tank( shown as Fig. 7). And then the water tank can be pushed into the cooler smoothly.

Cleaning the body

1. Remove plug from the wall outlet.
2. Do not use petrol, toluol, etc to clean the unit body. For slight dirt on the body, wipe it off with a soft damp cloth. For greasy dirt, use a mild detergent on a soft damp cloth, and then wipe the dirt off.
3. Let it dry completely before the next use.

Cleaning the mosquito reserving chamber

1. Remove the plug from the wall outlet. Remove some parts of the mosquito light trap in the order shown in (Figure 8) for cleaning.
2. Use a dry soft towel, or mild detergent to clean and wipe off the mosquito’s dead body and dirt.
3. Put the mosquito reserving chamber in place after cleaning.

( Note : Make sure the mosquito reserving chamber is dry and no water droplets to prevent any short circuit problems)

TROUBLESHOOTING

If there is something wrong during operation, it may not be the unit’s problem. You may check against the following list before sending for repair.

Notice :

1. If the problem cannot be found in the list or it persists, please contact our service center or a qualified technician for further inspection.
2. Do NOT open and repair the unit by yourself.

PACKING LIST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>