UURIG PH-10 Phone Camera Handle Grip with Light User Manual

PH-10
Phone Camera Handle Grip w Light

Product Description

1. Focus reduction button
2. Focus button
3. Shooting button
4. Type-C remote control charging port
5. Remote control indicator
6. Fill light switch/gear button
7. Cold shoe
8. Phone holder
9. Fill light
10. 1/4 screw hole
11. Fill light charging port

Bluetooth Pairing

1. Press and hold the shooting button for 3s to turn on the remote control, and the green indicator light flashes. Press and hold for 3s to power off.
2. Turn on the mobile phone’s Bluetooth to enter the search state.
3. In the device list, select “UURIG”, prompt “UURIG” pairing, click pairing,and it indicates that “UURIG” connected, the green indicator light is always on.
4. Click the shooting button to control the phone to take pictures. Enter the recording interface, click the button to start shooting,Start recording, click again to stop recording.
5. When charging, the red light keeps flashing, and the red light is on for 1-3 minutes and automatically turns off when fully charged.When battery is lower than 15%, the red light will flash until it is turned off. If there is no operation for 30 minutes, it will automatically，shutdown, and 3 minutes without connection automatic shutdown.
6. Some Android phones cannot focus, which is suitable for most mainstream Android phones. IOS only can control photo and video.

Fill Light Operation

1. Long press the power button for 3s to turn on, the default brightness is 30% . Short press the power button to adjust the brightness, which contains 30%/ 70%/100% brightness. Long press for 3s to shut down.
2. Under normal working conditions, the indicator light is green.
3. When charging,the red indicator light flashes, and when fully charged, the red indicator light stop flashing and green light is on.
4. When charging,red indicator flashes.
5. When the battery is lower than 30%, the green indicator light flashes; the battery is lower than 15%  (Insufficient to maintain the desired brightness) The red light flashes to shut down.

Phone Installation

Bluetooth Remote

Tips

1. The product has a built-in lithium battery, no need to replace the battery.
2. Using the remote control, when the battery is low, the red indicator light flashes, it needs to be charged in time.
3. A 5V/0.5A adapter charger is recommended. When charging is completed, the red light will turn off.
4. When not in use for a long time, it is recommended to charge the battery once every 2 months in order to maintain the normal function of the product.

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>