ring BHAXN001 Alarm Pro On Wall User Guide
- June 5, 2024
- Ring
Table of Contents
ring BHAXN001 Alarm Pro On Wall
Installation
- Drill two holes with a 3/16“ wood or masonry bit (as needed) for the anchors.
- These holes should be 58mm apart to fit the slots on the back of the Alarm Pro.
- Insert the anchors into the wall, then insert the screws.
- Mount the Ring Alarm Pro.
Safety Information
How to mount your Ring Alarm Pro on a wall (optional)
You can mount your Ring Alarm Pro on a wall using two wall anchors, two
screws, and the mounting slots located on the unit. It is only suitable for
mounting at heights ≤ 2m. If you
plan to use Ring Power Packs with your Alarm Pro, wall mounting is not
supported.
Note: Ring Alarm Pro is for indoor use only.
Before you begin, choose a wall mounting spot that is ≤ 2m high, free of
obstruction on all sides, and where the cables can reach the outlet and the
modem. The wall can be made of cement, wood, or drywall. Make sure you can
access the cables easily. You will also need the following items:
- Two wall anchors for #8 x 1-inch screws
- Two #8 x 1-inch pan head screws
IMPORTANT PRODUCT INFORMATION
SAFETY INFORMATION
Use Responsibly. Read all instructions and safety information before use.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER INJURY OR DAMAGE.
Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet and wait for the device and adapter to dry completely before plugging them in again. Do not attempt to dry your device or adapter with an external heat source, such as a microwave oven or a hair dryer. If the device or adapter appear damaged, discontinue use immediately. Use only accessories supplied with the device to power your device. To avoid risk of electric shock, do not touch your device or any wires connected to your device during a lightning storm.
Your Ring Alarm Pro may get hot during normal use. To reduce the effect of the warming, place your Ring Alarm Pro on a heat resistant surface. If you find the device has become hot to the touch, unplug power and let it cool down for a few minutes before handling. Your device should only be powered using the Ring USB-C power adapter Model: DSA-36PDB FUS included with the device, unless powered by a Ring Power Pack (sold separately).
Small parts contained in your device and its accessories may present a choking hazard to small children.
Your device is shipped with a Ring Power Adapter. If the Ring Power Adapter or cable appears damaged, discontinue using the supplied Ring Power Adapter. Install your power adapter into an easily accessible sock-et-outlet located near the equipment that will be plugged into or powered by the adapter.
BATTERY SAFETY
HANDLE WITH CARE. Your device contains a rechargeable lithium-ion battery and
should be replaced only by a qualified service provider. Do not disassemble,
open, crush, bend, deform, puncture, shred or attempt to access the battery in
your device. Do not modify or remanufacture the battery, attempt to insert
foreign objects into the battery, or immerse or expose it to water or other
liquids, expose to fire, explosion or other hazard. Only use the battery for
the system for which it is specified. Use of an unqualified battery or charger
may present a risk of fire, explosion, leakage or other hazard. Do not short-
circuit a battery or allow metallic conductive objects to come into contact
with battery terminals. Avoid drop-ping the device or battery. If the device
or battery is dropped, especially on a hard surface, and the user suspects
damage, do not attempt repair. Do not subject the battery to extremely low air
pressure that may result in an explosion or the leakage of flammable liquid or
gas.
Keep the device and its power adapter in a well-ventilated area and away from
heat sources, especially when in use or charging. Do not charge your device
near water or in extremely humid conditions. Contact Ring Customer Service for
assistance.
Maintaining Your Ring Alarm Pro
Only handle your device with clean hands. Clean your device only with a soft
cloth that is slightly damp with water and a touch of rubbing alco-hol; be
careful not to wipe it with anything abrasive or to use any harsh chemicals.
Don’t expose your device to steam or extreme heat or cold. For example, do not
install your device near any heat sources such as space heaters, heater vents,
radiators, stoves, or other things that produce heat. Store your Ring Alarm
Pro in cool, dust-free areas out of direct sunlight.
Use of third-party accessories may impact your devices’ performance. In
limited circumstances, use of third-party accessories may void your devices’
limited warranty. In addition, use of incompatible third-party accessories may
lead to damage to device or the accessory. Read all safety instructions for
any accessories before using with your Ring Alarm Pro.
PRODUCT SPECIFICATIONS
- Device Name: Ring Alarm Pro
- Model Number: 5AT3T3
- Electrical Rating: 12V DC, 3.0A
- Temperature Rating: 32°F to 104°F (0°C to 40°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your device in accordance with your local laws and regulations. For information about recycling your device, go to amazon.com/devicesupport.
TERMS OF SERVICE
By purchasing or using the product, you agree to the Terms of Service found at
ring.com/terms. By using the wifi router incorporated in the product, you
agree to eero’s Terms of Service found at eero.com/legal.
For information on our warranty and Ring Protect Plans, visit
ring.com/legal.
LIMITED WARRANTY
Your new or Certified Refurbished Ring Alarm Pro device is covered by a one- year Limited Warranty. Details are available at ring.com/warranty.
Supplier’s Declaration of Conformity – Compliance Information Statement
Unique Identifier: Ring Alarm Pro
Model Number: 5AT3T3
FCC ID: 2AEUPBHAXN001
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
Responsible Party and Party issuing Supplier’s Declaration of Conformity: Ring
LLC, 1523 26th Street, Santa Monica, CA 90404 U.S.A.
www.ring.com/legal@ring.com
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to a socket on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Pursuant to Section 15.21 of the FCC rules, changes or modifications to a
Product by the user that are not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
The device meets the FCC Radio Frequency Emission Guidelines. Information on
the product is on file with the FCC and can be found by inputting such
Product’s FCC ID (which can be found on the device) into the FCC ID Search
form available at fcc.gov/oet/ea/fccid.
This device complies with radio frequency radiation exposure limits set forth
for an uncontrolled environment. The antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 40 cm from all
persons and must not be co-located or operating in conjunction with any other
product antenna or transmitter.
Innovation, Science and Economic Development Canada (ISED) Compliance
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-ex-empt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an
uncontrolled environment. This device for operation in the band 5150-5250 MHz
is only for indoor use to reduce the potential for harmful interference to co-
channel mobile satellite systems. This equipment should be installed and
operated with a minimum distance of 40 cm between the radiator and your body.
Ring LLC 1523 26th St. Santa Monica, CA 90404
© 2021 Ring LLC or its affiliates. Ring and all related marks are trademarks
of Ring LLC or its affiliates.
For Z-Wave technical information, visit
ring.com/z-wave.
XX-XXXXXX-XX
References
- Amazon Digital Services and Device Support - Amazon Customer Service
- Legal: Terms of Service Agreement for US | eero
- Legal Information, Support & Resources | Ring
- Terms of Service | Ring
- Warranty – Ring
- Ring Alarm Z-Wave Technical Information
- Home Security Systems | Smart Home Automation | Ring
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>