renkforce 1277852 Wireless Barcode Scanner 1D ICR6307ABU Instruction Manual

renkforce 1277852 Wireless Barcode Scanner 1D ICR6307ABU

Operating instructions

• Wireless barcode scanner 1D ICR6307ABU
• Item no. 1277852

Intended use

• The product is used for contact-free reading of barcodes. Data is transferred from the scanner to the receiving station wirelessly. The transfer to PC is via USB.
• The barcode scanner functions in a manner similar to a wireless keyboard. It transmits the data contained in the scanned barcode as text to the receiver (e.g. a PC), which then shows this information in the currently running software (spreadsheet, text editor).
• The built-in battery provides the required power. It is automatically charged when the scanner is docked onto the charging cradle. The power is supplied only via the USB port on which the charging station or receiver is connected to your computer.
• It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be avoided under all circumstances.
• For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them. Make this product available to third parties only together with its operating instructions.
• This product complies with the statutory national and European requirements. All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery content

• Barcode scanner
• Charging station
• Operating instructions

Latest operating instructions

• Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

Explanation of symbols

• The lightning symbol inside a triangle is used when there is a potential risk of personal injury, such as electric shock.
• An exclamation mark in a triangle indicates important instructions in this operating manual that absolutely have to be observed.
• The arrow symbol indicates specific tips and advice on operation.

Safety instructions

• Read the operating instructions carefully and especially observe the safety information.
• If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property.
• Such cases will invalidate the warranty/guarantee.

General

• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:
  • is visibly damaged,
  • is no longer working properly,
  • has been stored for extended periods in poor ambient conditions or
  • has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Also observe the safety and operating instructions of any other devices which are connected to the product.
• Never look into the laser beam and never point it at people or animals. Laser radiation can seriously damage your eyes.
• Do not point the laser beam at mirrors or other reflective surfaces. The uncontrolled, reflected beam may strike people or animals.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.

Rechargeable batteries

• The rechargeable battery is permanently built into the product and cannot be replaced.
• Never damage the rechargeable battery. Damaging the casing of the rechargeable battery might cause an explosion or a fire!
• Never short-circuit the contacts of the rechargeable battery. Do not throw the battery or the product into fire. There is a danger of fire and explosion!
• Charge the rechargeable battery regularly, even if you do are not using the product. Due to the rechargeable battery technology being used, you do not need to discharge the rechargeable battery first.
• Never charge the rechargeable battery of the product unattended.
• When charging, place the product on a surface that is not heat-sensitive. It is normal that a certain amount of heat is generated during charging.

Commissioning

• First, shut down your computer to which you want to connect the scanner.
• Connect the USB cable of the charging station to a free USB port on your computer.
• Start the PC now and wait until the operating system has booted up completely.
• The scanner is automatically installed by the operating system.
• Then, turn on the scanner. To do this, you have to push the small grey snap switch on the bottom of the scanner using a sharp object.
• If you want to turn off the scanner later, actuate the switch again.
• You must fully charge the battery before first use. This takes about 5 to 6 hours. During charging, the LED on the top of the scanner flashes orange. The battery is full once it is constantly lit up orange.
• If the scanner LED lights up red permanently after docking it onto the charging cradle, you must reconnect the scanner with the station.
• To do this, scan the three bar codes on the bottom of the charging station in the sequence 1 to 3. You must do this within one minute after you have connected the charger to the USB port on your PC. If the station has been connected for more than one minute, pull the USB connector prior to scanning and plug it after a few seconds later.

Operation

• To scan a bar code, press and hold down the Scan button on the handle of the scanner and move the red bar above the barcode. Alternatively, you can also target the barcode and press the button.
• Once the scanner beeps, the code is read and transmitted to the receiver. At the same time, the LED on the scanner lights up green briefly.
• If the scanner is not used for more than a minute, it will automatically enter the standby mode. To reactivate the scanner, press the scan button. The LED flashes orange at first and then lights up red for a short time. Once this goes out again, the scanner is ready for use and is connected to the station.

General configuration

• The following description refers to the accompanying English programming instructions of the manufacturer.
• These instructions include all necessary codes that you need for configuration.
• Some of the configuration codes are listed next to each other.
• Here, you should cover the other codes with your hand or a piece of paper, except the one you want to scan.
• “Default” or “Original setting” refers to the factory settings.
• To change the settings, scan the barcode of each setting.
• The scanner must be in normal mode while doing this.
• If you, for example, want to change the keyboard language of the scanner to German, simply scan the barcode below
• “Germany”. The setting is applied immediately.

You can change the following settings

• The trigger mode.

• Here, you can select between “Trigger always” (barcodes can always be scanned) and “Trigger standard” (barcodes can only be scanned again if data transmission from the last scan has been completed).

• The transmission rate.

• Here, you can select six different speeds at which the data is transmitted to the PC.

• The automatic connection between the scanner and the station.

• Here, you can choose “Wireless Auto-connection ON” or “OFF”.

• When “ON”, the scanner does not enter the standby mode as soon as it leaves the receiving range of the station, but constantly searches the station.

• When “OFF”, the scanner automatically enters the standby mode after 2 minutes if it is out of range. If the scanner is again in the receiving range, simply press the scan button.

• The keyboard language.

• Here, you can select different keyboard languages. This is especially important if your barcode includes special characters such as y and z (e.g. it is swapped in the German and English keyboards).
  

• The standby mode.

• Here, you can select between “Power-Saving mode OFF” and “ON”. When “ON”, the scanner enters the standby mode after 1 minute of non-use. When “ON”, it is on permanently.

• Prefix and suffix.

• With this function, you can append either functions or characters to the scanned barcode. A maximum of 5 prefixes or suffixes can be appended.

• A function (prefix) would be, for example, if the “CTRL V” function is automatically performed after the scan to append a text to the barcode from the clipboard.

• A character (suffix) would be, for example, if the “+” character is appended automatically to the barcode while scanning.

• To configure, scan the “prefix” or “suffix” first and then the hexadecimal code from the table. Prefix is the left side of the table. The codes start from “01” to “1F”. Suffix is the right side of the table. The codes start from “20” to “7E”.

• If you do not program all 5 memory locations, scan the “X” at the end.

Programming the different barcode languages

In the as-delivered condition, the scanner can just read barcodes, such as standard EAN code “EAN-13”. Please proceed as follows, to program other codes. You can find the programming code in the “Barcode configuration method” chapter. The scanner must be in normal mode while programming.

• First, read the “Start configuration” barcode using the scanner.
• Then, you read the code to enable or disable the desired barcode language. You must always use “ENABLE” barcode to enable or “DISABLE” to disable which is in the same row as the desired language barcode.
• Finally, scan the “End configuration” barcode as the last code to exit the programming mode. If you want to enable or disable multiple barcode languages, it is enough if you read the “Start configuration” barcode once at the beginning and the “End configuration” bar code once at the end.
• In between, you can enable or disable any number of barcode languages.

Reset configuration to defaults

• Scan the seven bar codes, which are below “Reset Configuration to Defaults” section in the English programming instructions, following the sequence from 1 to 7.
• Then, the scanner is again reset to default values.

Care and cleaning

• Disconnect the product from the power supply before cleaning.
• The product requires no servicing on your part aside from occasional cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fiber-free cloth.
• Clean the product very carefully; otherwise you may scratch it.
• Do not press too heavily on the glass cover, as this can lead to breakage.
• Do not immerse the product in water.

Declaration of conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product conforms to the 2014/53/EU directive.

• Click on the following link to read the full text of the EU declaration of conformity: www.conrad.com/downloads.
• Select a language by clicking on a flag symbol and enter the product order number in the search box. You can then download the EU declaration of conformity in PDF format.

Disposal

• This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life.
• Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.
• Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):
  • in our Conrad offices
  • at the Conrad collection points
  • at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
• End users are responsible for deleting personal data from the WEEE to be disposed of.

Technical data

• Operating voltage …………………………5 V/DC
• Power supply ……………………………….via USB
• Power consumption during operation ……………………………max. 250 mA
• Power consumption while charging ………………………………max. 500 mA
• Charging time ………………………………5 – 6 hours
• Rechargeable battery …………………… 1 Li-ion rechargeable battery, 3.7 V/DC 3150 mAh, non-removable
• Scanner type ……………………………….1D, CCD engine
• Transmission frequency ………………..2.4 Ghz
• Frequency band ……………………………ISM Band for 2.4GHz (2400~2483.5MHz)
• Transmit power …………………………….max. up to +12dBm
• Range………………………………………… max. 100 m, in open space
• Scanning rate ………………………………max. 300 scans per second
• Operating temperature ………………….0 to +50 °C
• Storage temperature ……………………..-10 to +60 °C
• Air humidity ………………………………….5 – 95 % relative air humidity
• Supported barcodes …………………….. EAN-13, EAN-8, UPC-A, UPC-E, ISSN, ISBN, Codabar, Code 128, Code 93, ITF-6, ITF-14, Interleaved 2 of 5, Industrial 2 of 5, Matrix 2 of 5, GS1 Databar, Code 39, Code 11, MSI-Plessey, Plessey
• Supported Operating Systems ………. Windows® XP (only 32 bit), Windows Vista™, Windows® 7, Windows® 8 (32 and 64 bit); MacOS 9, MacOS X
• Length of the USB cable ………………..approx. 140 cm
• Dimensions (W x H x D) ………………..approx. 60 x 165 x 90 mm (barcode scanner)
• Weight……………………………………….. approx. 165 g (barcode scanner) approx. 225 g (charging station)

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing. Copyright 2023 by Conrad Electronic SE.

References

• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>