SW-MOTECH BC.TRS.00.409.50000 Legend Gear Leg Bag Set Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.TRS.00.409.50000 Legend Gear Leg Bag Set
Thank you for choosing this premium product from SW-MOTECH.
MOUNTING INSTRUCTIONS
Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw-motech.com
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference. SW-MOTECH assumes no liability for damages caused by improper fixation and handling.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Installed accessories can change driving behaviour
and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration.
PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Make sure to use only the appropriate tools. During installation have another person help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type.
ATTENTION: All components of the product must not contact any hot or moving
parts of the vehicle. All parts should also remain 5 cm away from hot parts of
the vehicle and remain clear of the exhaust stream. After mounting, make sure
there are no clearance issues while the suspension is both compressed and
extended.
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
LOADING INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
Never store pointy or sharp-edged objects in the product, which could cause injury to persons or damage to the vehicle/product.
Use a waterproof inner bag/raincover to protect your luggage from moisture. Additionally protect sensitive luggage (e.g., electronic equipment) from moisture with a plastic bag.
ATTENTION: Maximum load: 1 kg/ 2.2 lbs! The maximum vehicle load specified by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product, 130 km/h!
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a wear-effect and permanent stains can be prevented. Clean the product after riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Then rinse with clear water.
Before re-use dry the product for at least 24 hours in the air (not in direct sunlight).
We recommend to impregnate the cotton textile surface of the product in regular intervals or after intensive cleaning with a commercial wax impregnation (e.g. from Fjallravenl.
ATTENTION: Because the textile surfaces material is a natural fiber, it will experience color changes or fading when exposed to direct sunlight for extended periods of time and by environmental factors (e.g., SMOG, acid rain, etc.)! SW-MOTECH assumes no liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can
damage surfaces, such as the paint. Make sure that all areas of the vehicle,
which have contact with the product or parts of the product as straps, are
protected with an adhesive protection film from scratches and abrasions.
SW-MOTECH assumes no liability for paint damage and abrasions.
FIXATION
The bags [1a) – [1d) can be attached to many products of the Legend Gear series with the universal fixation system.
ATTENTION: Use the cell phone bag (1 d) only in combination with a tank bag or accessory bag LA2 /LAS, because the bag itself has no protection from moisture! Protect your smartphone with the rain cover of these bags from getting wet!
NOTE: The bags (1a/ – (1d/ should be only fixed in the empty state.
Run both straps through the loops [1] of your Legend Gear product, then through the loops [2] of the bag. Tighten the straps.
Now run the straps through the loops [3] and [4]. Tighten the fastening straps once more.
Now run the fastening straps through the loops [5]. Tighten the straps. Insert the reinforced ends of the straps completely into the loops [6] of the bag.
Check the proper fit of the bag.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>