ancona AN-3945 Tusca Dual-Mount 60 40 Double Bowl Kitchen Sink and Rivella Pull-Down Single Handle Kitchen Faucet Combo Owner’s Manual
- June 3, 2024
- ancona
Table of Contents
- ancona AN-3945 Tusca Dual-Mount 60 40 Double Bowl Kitchen Sink and
- INSTALLATION INSTRUCTIONS
- TOP-MOUNT INSTALLATION
- UNDERMOUNT INSTALLATION
- CARE AND MAINTENANCE
- ANCONA LIMITED LIFETIME WARRANTY
- Installation size map
- Tools might be applied to the following places
- Faucet Installation
- Checking and Testing
- Test Faucet Installation
- Cleaning and care
- Parts list
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ancona AN-3945 Tusca Dual-Mount 60 40 Double Bowl Kitchen Sink and
Rivella Pull-Down Single Handle Kitchen Faucet Combo
INSTALLATION INSTRUCTIONS
General Recommendations:
Read installation and maintenance instructions, thoroughly before
installation.
Be sure to use proper tools and always wear personal safety accessories for
your protection.
Warning: The enclosed cut-out template is provided as a guide only and
should be checked against actual sink to determine correct fit. Metal edges
may be sharp. Use gloves when handling.
Long-Life Care
Ancona Stainless Steel Sinks are easy to keep looking new, longer with minimal
care. For best results, always rinse with a mild soap and wipe after each use.
Rub lightly with soft cloth in the direction of the grain line on a regular
basis. To avoid damage and discoloration to the sink surface never use a steel
wool or scouring pad.
Tools and Materials needed:
- Tape Measure
- Pencil (NOT ink)
- Putty knife
- Scissors
- Adjustable wrenches
- Sealant drill and 1/2” (or larger) drill bits
- Silicone Adhesive Sealant Rags
- Denatured Alcohol
- Ear Protection
- Eye Protection
- Gloves
- Hacksaw/Jigsaw
- Mounting Clips (included)
- Cut-out template (included)
TOP-MOUNT INSTALLATION
Please carefully read complete instructions before beginning installation.
Note: These instructions are for installation with solid surface,
composite material countertops. Ancona recommends professional countertop
installers, customer is responsible for damage to the countertop or sink
during installation.
-
Unpack the new sink and check the contents of the materials supplied: sink, mounting brackets, and cut-out template (depending on model).
-
Preparing the countertop:
-
Place the template (B) on the countertop. Ensure the template (B) is centered on the counter so that it is parallel to the counter edge and that the installation hole will not
interfere with the structure of the cabinet. -
Tape the template (B) to the countertop to keep it in place and trace the outline on the template (B) with a pencil.
-
-
Cutting the installation hole:
Drill a pilot hole and cut the countertop opening. Use the appropriate cutting tool for the surface you are cutting.
-
Preparing the sink:
- Place the sink (A) into the installation hole to verify the fit. Adjust the cut-out if necessary.
- Place the sink (A) upside down and align the bottom edge with waterproofing strip.
-
Attaching the mounting clips:
Attach the top-mount clips (AA) to the sink (A).
-
Installing the sink:
- Apply silicone sealant (not included) around the underside and lip of the sink (A).
- Carefully lower the sink (A) into the counter.
- Tighten the screws on the top-mount clips (AA) evenly until the sink (A) is flush with the counter. Do not over-tighten.
- Wipe excess sealant with a rag.
-
Connect drain and water supply according to manufactures instruction.
UNDERMOUNT INSTALLATION
Please carefully read complete instructions before beginning installation.
Note: These instructions are for installation with solid surface,
composite material countertops. Ancona recommends professional countertop
installers, customer is responsible for damage to the countertop or sink
during installation.
-
Unpack the new sink and check the contents of the material supplied: sink, mounting brackets, and cut-out template (depending on model).
-
Position cut-out sink template as desired and trace it on the countertop.
-
Locate and drill the clearance hole inside the cut-out line.
-
Cut the countertop opening by carefully following the line traced from the template according to the countertop manufacturer’s instructions.
-
Drill faucet holes and install faucet according to manufacturer’s installation instruction.
-
Locate and drill the mounting holes (following the countertop manufacturer’s instructions) as shown below.
Holes should allow even spacing of mounting bracket around the sink.
-
Fasten mounting clip to countertop loosely.
-
Clean underside of the countertop and around cut-out area, making sure area is smooth and free of defects.
-
Apply a bead of sealant to the rim of sink, near the inside edge. Be careful not to miss or skip any area.
-
Carefully lift sink squarely under counter top cut-out. Press firmly on sink to form seal and seat sink.
Using a damp cloth, immediately wipe any excess sealant from edge of sink.
Do not smear or spread any excess sealant on counter top or sink. -
Turn all mounting bracket so they fit over sink rim. Check alignment of sink in cut out, adjust alignment as necessary. Tighten fasteners to secure sink.
-
Connect water supply lines to the faucet and complete the faucet installation. Connect drain assembly, hand tighten first to check alignment. Secure joint for water-tight assembly.
CARE AND MAINTENANCE
ALWAYS:
- Clean everyday by thoroughly rinsing with a mild soap and warm water and wipe dry. Some chemicals such as chlorides may corrode stainless steel, make sure you rinse the surface immediately.
- Rub lightly with a soft cloth in the direction of grain lines on a regular basis for additional preventive cleaning.
- Keep the sink free of any standing water as this can cause a buildup of mineral deposit, which can affect the appearance of your sink.
- Any stubborn stains should be removed by scrubbing in the direction of the grain with a mild abrasive such as Comet.
- Always rinse the sink after using any cleaning agent and wipe dry. Clean any mineral deposits built up over time with a mild solution of vinegar and water followed by a thorough flushing with water. Towel dry after each use to prevent mineral deposits from building up on the surface of the sink.
- Remove any scratches with a Scotch-brute pad and cleaning agent rubbing in the direction of the grain.
NOT RECOMMENDED FOR MIRROR FINISH.
NEVER:
- Leave water spots, steel cookware, utensils, wet sponges, cloths or cleaning pads in the sink for lengthy periods; iron particles often develop rust spots in the stainless steel surface.
- Use a steel wool or scoring pad as it damages the sink surface and causes discoloration.
- Rub the sink across the stainless steel finish lines.
- Let household cleaning agents or bleach sit in your sink for long period of time as this may ruin the finish of your sink.
- Leave rubber mats, sponges, or cleaning pads in the sink for long period of time as this may ruin the finish of your sink.
- Use any drain cleaning products containing sulfuric acid or hydrochloric acid as this will attach the sink. Silver cleaners can also contain acids that will damage the sink surface.
- Use the inside of the sink as cutting surface.
- Use a steel wool pad to clean your sink.
ANCONA LIMITED LIFETIME WARRANTY
This Ancona Sink product (the “Product”) is warranted by AMS, in the manner
fully set forth below, to be free from defects in material and workmanship and
to operate properly in accordance with specifications, provided that it is
used under the normal operating conditions and for ordinary home use and
service in Canada and the USA. AMS provides a limited lifetime warranty on
manufacturing defects in material and workmanship for its Products. This
warranty applies to the initial domestic installation only and only to the
original owner/purchaser. Proof of purchase (original sales receipt) must be
made available to AMS for all warranty claims. This limited warranty does not
apply to commercial installations. The warranty for commercial installations
is 90 days.
AMS will repair or replace at no charge excluding shipping and labour costs
any sink that has been proven to be defective under normal residential use
(or, if the Product is no longer available, replace the defective Product with
a comparable Product of equal or greater value). This lifetime limited
warranty DOES NOT apply to any defects or damages caused by, installation,
alterations, accidents, negligence, abuse, misuse, environmental factors or
lack of proper maintenance. Chips, scratches and stains are not considered
manufacturing defects, and this warranty DOES NOT apply to chips scratches and
stains that occur with normal use. The limited lifetime warranty excludes
labour costs and all shipping costs to and from the manufacturer and will be
the responsibility of the purchaser. AMS is not liable for any damage to
persons or property incurred in the installation and/or removal of the sink.
AMS will not be responsible for the cost of repair or replacement of any
materials used in the installation of the sink including but not limited to
tiles, granite, marble, etc. This warranty excludes any accessories that are
included with the sink including basket strainers.
AMS’S SOLE OBLIGATION AND THE CUSTOMER’S SOLE REMEDY FOR ANY DEFECTIVE PRODUCT
OR PART THEREOF SHALL BE LIMITED TO THE REPAIR AND REPLACEMENT THEREOF. AMS’S
ENTIRE AGGREGATE LIABILITY UNDER THE WARRANTY SHALL NOT EXCEED THE ORIGINAL
PURCHASE PRICE OF THIS PRODUCT (EXCEPT WHERE AMS, IN ITS SOLE DISCRETION,
DECIDES TO REPLACE THE PRODUCT WITH A PRODUCT OF GREATER VALUE).
PRIOR TO RETURNING ANY PRODUCT TO AMS, THE CUSTOMER MUST FIRST OBTAIN A RETURN
AUTHORIZATION NUMBER AND SHIPPING INSTRUCTIONS FROM AMS (AN “AUTHORIZATION”)
BY CALLING THE FOLLOWING NUMBER:
1-800-350-4562.
After having obtained an Authorization from AMS, the customer should promptly
ship the Product to the address specified in the Authorization with the
following documentation:
- a complete description of the problem;
- the Product model number;
- the date and location of Product purchase; and
- the original sales receipt to be valid.
This Warranty does not cover and AMS shall not be responsible for: (i) service
calls to correct the installation of the Product, to instruct the customer on
how to use the Product or any other customer education; (ii) accessory parts,
such as strainers; (iii) service outside the covered service area and (iv)
labour costs associated with the removal, shipping and reinstallation cost or
other contingent expenses.
Damages caused by accident, fire, lightning, brown-out, leaking, superior
force, improper installation, handling or operation, error, use for non-
domestic purposes, shipping damage, negligence, abuse, misuse, unauthorized
repair, whether performed by the customer or a third party, or improper care
or maintenance WILL IMMEDIATELY RENDER THIS WARRANTY NULL AND VOID AND AMS
WILL BE RELIEVED FROM ITS OBLIGATION TO WARRANT THE PRODUCT.
AMS WILL NOT BE LIABLE FOR DAMAGES TO PERSONS OR PROPERTY IN CONNECTION WITH
THE INSTALLATION, REPAIR OR REPLACEMENT OF THE PRODUCT, NOR FOR ANY INDIRECT,
SPECIAL, PUNITIVE, EXEMPLARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSSES,
INJURY OR COSTS OF ANY NATURE, INCLUDING, WITHOUT LIMITATION, LOSS OF USE OR
MALFUNCTION RELATING TO THIS PRODUCT. THIS WARRANTY IS NOT TRANSFERABLE OR
ASSIGNABLE TO ANY PERSON.
SAVE AS HEREIN PROVIDED, THERE ARE NO OTHER WARRANTIES, CONDITIONS,
REPRESENTATIONS OR GUARANTEES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
MADE OR INTENDED BY AMS OR ITS AUTHORIZED DISTRIBUTORS.
Some provinces or states may not allow limitations on the exclusion or
limitation of incidental or consequential damages, so these limitations and
exclusions may not entirely apply to certain customers. Any provision in the
Warranty which is unenforceable in any province or state shall be ineffective
to the extent of such unenforceability, without invalidating the remaining
provisions or affecting the validity or enforceability of such provisions in
any other province or state.
This Warranty gives the customer specific legal rights, and the customer may
also have rights which vary based on state, province or country. For service
and assistance, please call:
1-800-350-4562, or email us at:
service@anco-nahome.com
Rinella
Single Handle Pull-out Kitchen Faucet
STANDARDS
- ASME A112.18.1/CSA B125.1
- ASME A112.18.2/CSA B125.2
- LISTED IAPMO/cUPC
- 1.8 gpm/6.8 L/min
Helpful Information
Tools:
Gather the necessary tools as shown below to complete the installation of this
faucet. Some may not be needed depending on the model of faucet you are
installing. Check with your local hardware store on the requirements of your
installation situation.
Attention:
For easy installation, you will need:
- To read all the installation instructions completely before beginning.
- To read all the warning, attention and maintenance information.
- To purchase the proper supply lines.
Important
Tighten connection with two wrenches to prevent damage to tube body. Be careful not to bend the stem as this will void the product warranty.
Installation size map
Tools might be applied to the following places
Faucet Installation
-
General step
Position the faucet on the counter-top as shown. Add the O-ring and assemble the gasket assembly and lock nut to the threaded faucet sleeve and tighten the screws with screwdriver. -
Step for top mount stainless steel sinks or decks smaller than ½ inch
Secure the faucet body to the deck surface with the quick connect base. The quick connect base will provide a more stable and secure installation as it enlarges the contact area with sink.
Connect the shower hose to quick connect. CAUTION: MAKE SURE THE HOSE IS
PROPERLY ENGAGED AND SECURED IN THE QUICK CONNECT.
Disassemble the weight and put it on the shower hose. Then fix screws with
screwdriver.
Connect to water supply lines with either:
- 3/8” O.D. copper tubing (ball nose risers with the coupling nuts) or;
- 3/8” copper tubing (no ball) with supplied tube head interior connector or;
- IPS faucet connectors (1/2”).
Checking and Testing
Remove the shower by hand. Turn the faucet handle all the way on, turn on hot
and cold water supply and flush water lines for one minute. Reinstall shower
by hand. Check all connections at arrows for leaks and retighten if necessary.
BUT DON’T OVERTIGHTEN.
Test Faucet Installation
- Move handle into “OFF” position.
- Turn on water supplies. Check connections for leaks.
- Remove hand shower and let both hot and cold water run for one minute. This will help clean any debris that might otherwise clog the system. Replace hand shower.
- Operate handle up and down, in cold and hot positions, to flush water lines thoroughly.
Maintenance:
Simply rinse the surface with clear water or mild liquid detergents (if
necessary). Dry the faucet with a clean soft cotton cloth. Do not use any
cleaning agents containing acids polish abrasives or harsh cleaners.
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
- Clean it with water and dry it with soft cloth.
- Clean the product with gentle liquid or glass cleaner.
- Don’t use acid cleaner.
- Don’t clean with abrasive material, abrasive paper or knife.
WARNING
Ensure hoses are tightly screwed in position as they may move during
transportation and installation.
Parts list
NO. | PART NAME |
---|---|
1 | Body |
2 | Cartridge base |
3 | Cartridge sleeve |
4 | Cartridge |
5 | Fixing cartridge nut |
6 | Trim cap |
7 | Index |
8 | Screw |
9 | Handle |
10 | O-ring |
11 | Washer |
12 | Screw cap |
13 | Spout |
14 | Shower sleeve |
15 | Shower head |
16 | Pull-out flexible hose |
17 | Flexible hose (red) |
18 | Flexible hose (blue) |
19 | Outlet flexible hose |
20 | Non-returnable valve |
21 | Quick connect |
22 | Base |
23 | O-ring |
24 | Connector |
25 | Washer |
26 | Plate |
27 | Nut |
28 | Threaded pipe |
29 | Screw |
30 | Pull-out sleeve |
31 | Weight |
32 | Allen key |
33 | Quick connect base |
34 | Sponge plate |
35 | Deck plate |
36 | Gasket |
37 | Screw |
38 | Plastic nut |
39 | Aerator wrench |
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>