MEAN WELL ELGT-150-C Class Ⅱ Constant Current Mode LED Driver Instruction Manual

ELGT-150-C Class Ⅱ Constant Current Mode LED Driver
Instruction Manual
ELGT-150-Cseries

http://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf

Features

Metal housing design with functional Ground
Class II design
Constant Current mode output
Built-in active PFC function
No load / Standby power consumption <0.5W
IP67 / IP65 rating for indoor or outdoor installations
Function options: output adjustable via potentiometer;
3 in 1 dimming (dim-to-off); Smart timer dimming; DALI;
Typical lifetime>50000 hours
5 years warranty

Applications

LED street lighting
LED harbor lighting
LED bay lighting
LED greenhouse lighting
LED flood lighting
Comply with class II application

GTIN CODE

MW Search: [httosleiwww.meanwell.com(serviceGTIN.aspx](http://httosleiwww.meanwell.com\(serviceGTIN.aspx)

Description

ELGT-150-C series is a 105-150W LED AC/DC classic driver featuring the constant current mode and high voltage output. ELGT-150-C operates from 100-305VAC and offers models with different rated currents ranging between 700mA and 1400mA. Thanks to the high efficiency of up to 92%, with the fanless design, the entire series is able to operate for -40 C-+90 C case temperature under free air convection. The design of metal housing and IP67/1P65 ingress protection level allows this series to fit both indoor and outdoor applications. ELGT-150-C is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for the LED lighting systems.

 Model Encoding

3 in 1 dimming function (0-10Vdc, 10V PWM signal and resistance)
DA| IP67| DALI control technology.
D2| IP67| Built-in Smart timer dimming and programmable function.

SPECIFICATION

149.8W 150.15W 149.8W
IOOVAC – 18CNAC
105W| 105W| 105W
CONSTANT CURRENT REOCNitta| 107 – 214V| 7 2 – 143V| 54 – 107V
OPEN CRCUIT VOLTAGEepeu| 225V| 151V| 115V
CURRENT ADJ. RANGE| Adjusts tie KR A/A8-Type only (via brit-E% potentiometer)
3W – 700mA 525 – 1050mA 700 – 1400mA
CURRENT RIPPLE| 50% max. ©re led current
CURRENT TOLERANCE| ±5.0%
SET UP TIME paw<| 160Oms1115VAC 500ms/230NAC
INPUT| VOLTAGE RANGE moo| 100- 305VAC 142 – 431VDC
(Please refer to the “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE| 47 – 63Hz
POWER FACTOR drat| PF L. 0.97/115VAC, PRL095/230VAC, PF>092/277VACfpful load (Please refer to ‘POWER FACTOR (PF)CHARACTERISTIC section)
RM  TOTAL HA ONICDISTORTION| IND< 20%(@bacg50%/115VC:©Icedt60%/230VAC; @loacg75%/277VAC) ( Plea se refer to ‘TOTAL HARMONIC D ISTORTION(T HD)” s ection)
EFFICIENCY(rw)| 92%| I92%| I91%
AC CURRENT/rye)| I.7A/ II 5VAC 0.9A / 230VAC 0.7A/277VAC
INRUSH CURRE NTme.)| COLD START 65A(twith$85ps measured at 50% Speak)/230VAC; Per NE MA 410
MAX. No. of PS Us on 16A CIRCUIT BREAKER| 3 wits (cacti’ breaker of Noe El) 16 units (circuit breaker of type at 230VAC
LEAKAGE CURRENT| <0.7mA/ 240VAC
NO LOAD 1 STAND-BY POWER CONSUMPTION| No bad power consumption <0.5W for Blank / A/ D2-Type Standby power consumption <0.5W fa B / DA-Type
protect| SHORT CIRCUIT| Hiccup mode recovers automatically after fall modal: on is removed
OVERVOLTAGE| 230 – 265V 1155 -180V 1128  – 1 5W
Shut down of voltage. re-power on to recover
OVER TEMPERATURE| Shut down o/p vd tags, re-power onto recover
RIWIONMENT| WORKING TEMP.| Tcase= 40 -+90C (Please refer to” OUTPUT LOAD vs TEMPERATURE section)
MAX. CASE TEMP.| Tcasem•SOt
WORKING HUMIDITY| 20 – 95% RH non-condensing
STORAGE TEMP, HUMIDITY| -40- +800 , 10 – 95% RH
TEMP. COEFFICIENT| ±0.03%1 C (0- 60C)
VIBRATION| 10- 5C0Hz, 5G 12mi nilcycie, period for 72min. each along X, Y, and Z axes
SAFETY 8
EMC| SAFETY STANDARDS| ENEC BS EN/EN61347-1(except for AB-Type), BS EN/EN61347-2-13(except for AB-Type) iidependent, BS EN/EN62384(except for AB- Type); EAC TP TC 004 JP65 or IP67 approved
DALI STANDARDS| Complexe to IEC62386-101, 102, 207 for DA-Type only
WITHSTAND VOLTAGE| UP-0/P:3.75KVAC I/P-CASE:3.75KVAC 0/P-CASE:1.5KVAC
ISOLATION RESISTANCE| I!P-O/P, UP- FG, 0/ P- FG:100M Ohms! 500VDC / 25′(2170% RH
EMC EMISSION| Corrphance to BS EN/EN55015.BS ENIN61000-3-2 Class C (lt load .r 60%) : BS E WEN61000-3-3: EAC TP TC 020
EMC IMMUNITY| Canplence to BS EN/EA€1000-4-2,3,4,5,6,8.11; BS EN/EN61547, ig hl industry level (surge Mmunily Lbe-Earti 6KV, Lbe-Lbe4KV); EAC TP TC 020
OTHERS| MTBF| 31(6.9K hrs min. Telcordia S R-332 (Bellcore):294.8K hrs min. MIL- HDBK-217F (25″C )
DIMENSION| 219163’35.5mm (L1/41-1)
PACKING| 0.95Kg: 16pcs / 16.0(g / 0.77CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated current, and 25 C of ambient temperature.
2. Please refer to “DRIVING METHODS OF LED MODULE”. For DA-Type, the Constant Current region is 60%-100% of maximum voltage underrated power delivery.
3. De-rating may be needed under low input voltages. Please refer to the “STATIC CHARACTERISTIC” sections for details.
4. The length of set-up time is measured at the first cold start. Turning ON/OFF the driver may lead to an increase in the setup time.
5. The driver is considered as a component that will be operated in combination with the final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly@ point (or TMP, per DLC), is about 75°C or less.
7. Please refer to the warranty statement on MEAN WELL’s website at https://www.meanwell.com 
8. The ambient temperature derating of 3.5°C/1000m with fanless models and 5°C/1000m with fan models for operating altitudes higher than 2000m(6500ft).
9. For any application note and IP waterproof function installation caution, please refer to our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
10. To fulfill the requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without being permanently connected to the mains.

• Product Liability Disclaimer: For detailed information, please refer to https://www.meanwell.coni/serviceDisclaimer.aspx 

BLOCK DIAGRAM

DRIVING METHODS OF LED MODULE

※ This series works in constant current mode to directly drive the LEDs.

◎ This characteristic applies to Blank/A/B/AB/D2-Type, For DA-Type, the Constant Current area is 60%~100% Vo.

DIMMING OPERATION

※ 3 in 1 dimming function (for B/AB-Type)
Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-:
0 ~ 10VDC, or 10V PWM signal or resistance.
Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.
Dimming source current from power supply: 100 A (typ.)
◎ Applying additive 0 ~ 10VDC

◎ Applying additive 10V PWM signal (frequency range 100Hz ~ 3KHz):

◎ Applying additive resistance:

Note :

1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%.
2. The output current could drop down to 0% when dimming input is about 0kΩ or 0Vdc, or 10V PWM signal with a 0% duty cycle.

※ DALI Interface (primary side; for DA-Type)

• Apply DALI signal between DA+ and DA-.
• DALI protocol comprises 16 groups and 64 addresses.
• The first step is fixed at 8% of output.

※ Smart timer dimming function (for D2-Type by User definition)
MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details.

Ex : ◎ D01-Type: the profile recommended for residential lighting

**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level.
Example: If a residential lighting application adopts D01-Type when turning on the power supply at 6:00 pm, for instance:

1. The power supply will switch to the constant current level at 100% starting from 6:00 pm.
2.  The power supply will switch to the constant current level at 70% in turn, starting from 0:00 am, which is 06:00 after the power supply turns on.
3.  The power supply will switch to the constant current level at 50% in turn, starting from 1:00 am, which is 07:00 after the power supply turns on.
4.  The power supply will switch to the constant current level at 70% in turn, starting from 5:00 am, which is 11:00 after the power supply turns on.
   The constant current level remains till 8:00 am, which is 14:00 after the power supply turns on.

**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level.
Example: If a street lighting application adopts D02-Type when turning on the power supply at 5:00 pm, for instance:

1.  The power supply will switch to the constant current level at 50% starting from 5:00 pm.
2.  The power supply will switch to the constant current level at 80% in turn, starting from 6:00 pm, which is 01:00 after the power supply turns on.
3. The power supply will switch to the constant current level at 100% in turn, starting from 8:00 pm, which is 03:00 after the power supply turns on.
4. The power supply will switch to the constant current level at 60% in turn, starting from 1:00 am, which is 08:00 after the power supply turns on.
5.  The power supply will switch to the constant current level at 80% in turn, starting from 4:00 am, which is 11:00 after the power supply turns on. The constant current level remains till 6:30 am, which is 14:00 after the power supply turns on.

**: TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level.
Example: If a tunnel lighting application adopts D03-Type when turning on the power supply at 4:30 pm, for instance:

1. The power supply will switch to the constant current level at 70% starting from 4:30 pm.
2.  The power supply will switch to the constant current level at 100% in turn, starting from 6:00 pm, which is 01:30 after the power supply turns on.
3.  The power supply will switch to the constant current level at 70% in turn, starting from 5:00 am, which is 11:00 after the power supply turns on.
   The constant current level remains till 6:30 am, which is 14:00 after the power supply turns on.

OUTPUT LOAD vs TEMPERATURE(NOTE 7.)

STATIC CHARACTERISTIC

※De-rating is needed under low input voltage.

POWER FACTOR (PF) CHARACTERISTIC

TOTAL HARMONIC DISTORTION (THD)

EFFICIENCY vs LOAD

ELGT-150-C series possess superior working efficiency that up to 92% can be reached in field applications.
※ 700mA Model, Tcase at 75℃

LIFETIME

MECHANICAL SPECIFICATION

※ Blank-Type

※ B/DA/D2-Type

※ A-Type

※ AB-Type

MANUAL INSTALLATION

Please refer to: http://www.meanwell.com/manual.html

File Name:ELGT-150-C-SPEC 2022-03-16

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>