CORNAT TECBE3300 Shower Set Instruction Manual
- June 4, 2024
- CORNAT
Table of Contents
TECBE3300
Instruction-manual / Warranty terms
Instruction-manual:
Please note the following points before installation:
– Installation should only be performed by experienced technicians under the
consideration of DIN1988 and VOB.
– Before starting the installation, please stop the water supply (ideally,
close the main valve at the water meter).
– Please make sure that during assembly all seals fit properly (Always check –
water damage is possible)
– The fitting is suitable for use in private households and only in rooms with
a temperature above 0 °C. If there is a risk of frost, the water supply should
be interrupted and the valve must be completely emptied.
– Always before the first use and when a fitting has not been used for a
prolonged period, you should let rinse out a larger amount of water (water
stagnation) before drinking water is taken!
– Important MOUNTING Note:
The flexible connection hoses may only be hand screwed into the fitting. Do
not use under any circumstances tools like pliers or wrenches.
Operating conditions:
| Hot water temperature | max. 80 ° Celsius |
|---|---|
| Test pressure | max. 16 bar |
| Operating pressure | max. 10 bar |
| Holding pressure for shower conversion | min. 0.8 bar |
(To keep noise level DIN 4109 pressure reducers have to be installed in the main line for pressures of more than 6 bar). Reserve technical changes.
Care instructions:
Sanitary taps require special care. Please note the following information:
Chrome surfaces are sensitive to chemicals, acid-containing cleaning
supplies, and all kinds of abrasives.
Occasionally clean with soapy water, using a soft cloth. Remove lime deposits
with household vinegar.
Colored surfaces:
The surfaces of these taps are sealed with a special baking varnish. Do not
clean with abrasive, corrosive, or cleaners containing alcohol.
Clean only with cold water and a soft cloth or leather.
Surface damages can be expected especially in colored fittings for
inobservance of care instructions. Warranty claims will not be asserted.
Wandhalter wall mount
Warranty terms
Warranty Conditions for the Manufacturer
Warranty of Conmetall Meister GmbH
The warranty below does not affect, and in particular, does not restrict or
rule out, your statutory rights vis-à-vis the respective seller with regard to
defects. These statutory rights exist irrespective of whether an event
bringing the warranty into operation occurs or whether you assert rights based
on the warranty below.
We guarantee that the item you have purchased and that has come with these
warranty conditions will function without defects and be free of defects in
materials and/or workmanship and of design flaws for the term of the warranty.
This warranty commences on the date of purchase; the term of the warranty is
shown in the warranty logo affixed to the item purchased. The start of the
warranty must be documented by presenting the purchase receipt. If an event
bringing the warranty into operation occurs and we repair the item in question
or provide a new item as a replacement, the term of the warranty is not
extended as a result thereof.
There are no claims under this warranty if
- the item merely exhibits signs attributable to normal wear and tear,
- the item exhibits damage or signs of wear that are caused by use other than as normally intended and/or in deviation from the stipulations of the operating instructions,
- the item exhibits signs indicating that repairs or other interventions have been performed by unauthorized third parties, and/or
- accessories not authorized by us have been installed in the item or used with the item.
- Samples and display items are entirely excluded from this warranty.
To assert a claim under this warranty, you are required to show the item and
the purchase receipt in the place where you purchased the item and turn them
in there with as detailed and specific a description as possible of the event
bringing the warranty into operation. The item will not be repaired or
exchanged there. The item will be sent to us so we have a chance to examine
it. If an event bringing the warranty into operation has occurred, we are free
to choose whether to repair the item or replace it with a new item. You have
no claims beyond that under this warranty.
If no event bringing the warranty into operation has occurred, the item will
be sent back to you directly. We will notify you of this beforehand and, if
possible, offer to perform a paid repair and provide you with a cost
estimate. If you decline to have the item repaired, or if we do not hear from
you within 14 calendar days after transmitting the cost estimate to you, the
item will be sent back.
This warranty is only valid for items purchased in the Federal Republic of
Germany and only where a return address located in the Federal Republic of
Germany is stated. The warranty itself is governed by the laws of the Federal
Republic of Germany, to the exclusion of the United Nations Convention on
Contracts for the International Sale of Goods (CISG).
The guarantor is
Conmetall Meister GmbH, Hafenstrasse 26, 29223 Celle, Germany.
17.08.2017
Batch number:
Conmetall Meister GmbH • Hafenstraße 26 • 29223 Celle • GERMANY •
www.conmetallmeister.de
07/2022
Documents / Resources
|
CORNAT TECBE3300 Shower
Set
[pdf] Instruction Manual
TECBE3300 Shower Set, TECBE3300, Shower Set
---|---