CORNAT TECBE3302 Noir Round Head Shower Instruction Manual
- June 4, 2024
- CORNAT
Table of Contents
CORNAT TECBE3302 Noir Round Head Shower Instruction Manual
Instruction manual
Please note the following points before installation:
-
Installation should only be performed by experienced technicians under the consideration of DIN1988 and VOB.
-
Before starting the installation, please stop the water supply (ideally close the main valve at the water meter).
-
Please make sure that during assembly all seals fit properly (Always check – water damage possible)
-
The fitting is suitable for use in private households and only in rooms with a temperature above 0 °C.
If there are a risk of frost, the water supply should be interrupted and the valve must be completely emptied. -
Always before the first use and when a fitting has not been used for a prolonged period, you should let rinse out a larger amount of water (water stagnation) before drinking water is taken!
Important Note:
The flexible connection hoses may only be hand screwed into the fitting. Do not use under any circumstances tools like pliers or wrenches
Operating conditions:
Hot water temperature max: 80 ° Celsius
Test pressure max: 16 bar
Operating pressure max: 10 bar
Holding pressure for shower conversion min: 0.8 bar
(To keep noise level DIN 4109 pressure reducers have to be installed in the
main line for pressures of more than 6 bar).
Reserve technical changes.
Care instructions:
Sanitary taps require special care. Please note the following information:
Chrome surfaces:
are sensitive for chemicals, acid-containing cleaning supplies and all kinds
of abrasives.
Occasionally clean with soapy water, using a soft cloth. Remove lime deposits
with household vinegar.
Colored surfaces:
The surfaces of these taps are sealed with a special baking varnish. Do not
clean with abrasive, corrosive or cleaners
containing alcohol.
Clean only with cold water and a soft cloth or leather.
Surface damages can be expected especially in colored fittings for in
observance of care instructions. Warranty claims will not be asserted.
Beginnings Handling
| Nr | Designation |
|---|
1
| Dowel
2|
Wall mount
3
| Fastening screw
4|
Shower hose 150 cm
5
| Connection hose 50 cm
6|
Handheld shower
7
| Head shower
8|
Showerhead slider
9
|
Diverter
Dimension
Assembly instruction
Warranty Conditions for the Manufacturer
Warranty of Conmetall Meister GmbH
The warranty below does not affect, and in particular does not restrict or rule out, your statutory rights vis-à-vis the respective seller with regard to defects. These statutory rights exist irrespective of whether an event bringing the warranty into operation occurs or whether you assert rights based on the warranty below
We guarantee that the item you have purchased and that has come with these warranty conditions will function without defects and be free of defects in materials and/or workmanship and of design flaws for the term of the warranty. This warranty commences on the date of purchase; the term of the warranty is shown in the warranty logo affixed to the item purchased. The start of the warranty must be documented by presenting the purchase receipt. If an event bringing the warranty into operation occurs and we repair the item in question or provide a new item as a replacement, the term of the warranty is not extended as a result thereof.
There are no claims under this warranty if
- The item merely exhibits signs attributable to normal wear and tear,
- The item exhibits damage or signs of wear that are caused by use other than as normally intended and/or in deviation from the stipulations of the operating instructions,
- The item exhibits signs indicating that repairs or other interventions have been performed by unauthorized third parties, and/or
- Accessories not authorized by us have been installed in the item or used with the item.
- Samples and display items are entirely excluded from this warranty.
To assert a claim under this warranty, you are required to show the item and
the purchase receipt in the place where you purchased the item and turn them
in there with as detailed and specific a description as possible
of the event bringing the warranty into operation. The item will not be
repaired or exchanged there. The item will be sent to us so we have a chance
to examine it. If an event bringing the warranty into operation has
occurred, we are free to choose whether to repair the item or replace it with
a new item. You have no claims beyond that under this warranty.
If no event bringing the warranty into operation has occurred, the item will
be sent back to you directly. We will notify you of this beforehand and, if
possible, offer to perform a paid repair and provide you with a cost estimate.
If you decline to have the item repaired, or if we do not hear from you within
14 calendar days after transmitting the cost estimate to you, the item will be
sent back.
This warranty is only valid for items purchased in the Federal Republic of
Germany and only where a return address located in the Federal Republic of
Germany is stated. The warranty itself is governed by the laws of the Federal
Republic of Germany, to the exclusion of the United Nations Convention on
Contracts for the International Sale of Goods (CISG).
The guarantor is Conmetall Meister GmbH, Hafenstrasse 26, 29223 Celle, Germany.
Symbol
Batch number:
http://www.conmetallmeister.de/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>