CORNAT WT-EHM Basin Mixer Fabio Chrome Instruction Manual
- June 12, 2024
- CORNAT
Table of Contents
CORNAT WT-EHM Basin Mixer Fabio Chrome
Product Information
Product Name: WT-EHM
Installation and Operating Instructions:
Please note the following points before installation:
- Installation should only be performed by experienced technicians under the consideration of DIN1988 and VOB.
- Before starting the installation, please stop the water supply (ideally close the main valve at the water meter).
- Please make sure that during assembly all seals fit properly (Always check – water damage possible).
- Always before the first use and when a fitting has not been used for a prolonged period, you should let rinse out a larger amount of water (water stagnation) before drinking water is taken!
- Important MOUNTING Note: The flexible connection hoses may only be hand screwed into the fitting. Do not use under any circumstances tools like pliers or wrenches.
Operating conditions:
- Hot water temperature: max. 16 bar
- Operating pressure: max. 10 bar
- Holding pressure for shower conversion: min. 0.8 bar (To keep noise level DIN 4109 pressure reducers have to be installed in the main line for pressures of more than 6 bar).
Care instructions:
Sanitary taps require special care. Please note the following information:
- Chrome surfaces: are sensitive for chemicals, acid-containing cleaning supplies and all kinds of abrasives. Occasionally clean with soapy water, using a soft cloth. Remove lime deposits with household vinegar.
- Colored surfaces: The surfaces of these taps are sealed with a special baking varnish. Do not clean with abrasive, corrosive or cleaners containing alcohol. Clean only with cold water and a soft cloth or leather.
- Surface damages can be expected especially in colored fittings for inobservance of care instructions. Warranty claims will not be asserted.
Product Usage Instructions
1. Before starting the installation, ensure that the water supply is turned
off. Ideally, close the main valve at the water meter.
2. The installation should only be performed by experienced technicians who
follow DIN1988 and VOB guidelines.
3. During assembly, ensure that all seals fit properly to avoid water damage.
4. Before using the fitting for the first time or after a prolonged period of
non-use, it is recommended to rinse out a larger amount of water to remove any
water stagnation before using it for drinking water.
5. When mounting the flexible connection hoses, only hand screw them into the
fitting. Do not use tools like pliers or wrenches.
6. The product has specific operating conditions:
- Hot water temperature: maximum 16 bar
- Operating pressure: maximum 10 bar
- Holding pressure for shower conversion: minimum 0.8 bar (For
- pressures higher than 6 bar, pressure reducers according to DIN 4109 should be installed in the main line to reduce noise level).
7. To maintain the product’s appearance, follow these care instructions:
- For chrome surfaces, clean occasionally with soapy water using a soft cloth. Remove lime deposits with household vinegar. Avoid using chemicals, acid-containing cleaning supplies, or abrasives.
- For colored surfaces, clean only with cold water and a soft cloth or leather. Do not use abrasive, corrosive, or alcohol-containing cleaners.
- Note that surface damages can occur, especially in colored fittings, if care instructions are not followed. Warranty claims will not be accepted for such damages.
The illustrations serve as visual depictions. Product changes are possible. Subject to change.
Instruction-manual
Please note the following points before installation:
-
Installation should only be performed by experienced technicians under the consideration of DIN1988 and VOB.
-
Before starting the installation, please stop the water supply (ideally close the main valve at the water meter).
-
Please make sure that during assembly all seals fit properly (Always check – water damage possible)
-
The fitting is suitable for use in private households and only in rooms with a temperature above 0 °C.
If there are a risk of frost, the water supply should be interrupted and the valve must be completely emptied. -
Always before the first use and when a fitting has not been used for a prolonged period, you should let rinse out a larger amount of water (water stagnation) before drinking water is taken!
-
Important MOUNTING Note:
The flexible connection hoses may only be hand screwed into the fitting. Do not use under any circumstances tools like pliers or wrenches.
Operating conditions
- Hot water temperature max. 80 ° Celsius
- Test pressure max. 16 bar
- Operating pressure max. 10 bar
- Holding pressure for shower conversion min. 0.8 bar
(To keep noise level DIN 4109 pressure reducers have to be installed in the
main line for pressures of more than 6 bar).
Reserve technical changes.
Care instructions
Sanitary taps require special care. Please note the following information:
Chrome surfaces:
are sensitive for chemicals, acid-containing cleaning supplies and all kinds
of abrasives.
Occasionally clean with soapy water, using a soft cloth. Remove lime deposits
with household vinegar.
Colored surfaces:
The surfaces of these taps are sealed with a special baking varnish. Do not
clean with abrasive, corrosive or cleaners containing alcohol.
Clean only with cold water and a soft cloth or leather.
Surface damages can be expected especially in colored fittings for
inobservance of care instructions. Warranty claims will not be asserted.
INSTALLATION
The illustrations serve as visual depictions.
Maintenance
Cold water
Hot water
Warranty terms
Warranty Conditions for the Manufacturer Warranty of Conmetall Meister GmbH
The warranty below does not affect, and in particular does not restrict or rule out, your statutory rights vis-à-vis the respective seller with regard to defects. These statutory rights exist irrespective of whether an event bringing the warranty into operation occurs or whether you assert rights based on the warranty below.
We guarantee that the item you have purchased and that has come with these warranty condi-tions will function without defects and be free of defects in materials and/or workmanship and of design flaws for the term of the warranty. This warranty commences on the date of purchase; the term of the warranty is shown in the warranty logo affixed to the item purchased. The start of the warranty must be documented by presenting the purchase receipt. If an event bringing the warranty into operation occurs and we repair the item in question or provide a new item as a replacement, the term of the warranty is not extended as a result thereof.
There are no claims under this warranty if
- the item merely exhibits signs attributable to normal wear and tear,
- the item exhibits damage or signs of wear that are caused by use other than as normally intended and/or in deviation from the stipulations of the operating instructions,
- the item exhibits signs indicating that repairs or other interventions have been performed by unauthorized third parties, and/or
- accessories not authorized by us have been installed in the item or used with the item.
- Samples and display items are entirely excluded from this warranty.
To assert a claim under this warranty, you are required to show the item and the purchase receipt in the place where you purchased the item and turn them in there with as detailed and specific a description as possible of the event bringing the warranty into operation. The item will not be repaired or exchanged there. The item will be sent to us so we have a chance to examine it. If an event bringing the warranty into operation has occurred, we are free to choose whether to repair the item or replace it with a new item. You have no claims beyond that under this warranty. If no event bringing the warranty into operation has occurred, the item will be sent back to you directly. We will notify you of this beforehand and, if possible, offer to perform a paid repair and provide you with a cost estimate. If you decline to have the item repaired, or if we do not hear from you within 14 calendar days after transmitting the cost estimate to you, the item will be sent back. This warranty is only valid for items purchased in the Federal Republic of Germany and only where a return address located in the Federal Republic of Germany is stated. The warranty itself is governed by the laws of the Federal Republic of Germany, to the exclusion of the United Nations Convention on Contracts for the International Sale of Goods (CISG).
The guarantor is Conmetall Meister GmbH, Hafenstrasse 26, 29223 Celle,
Germany.
17.08.2017
Conmetall Meister GmbH · Hafenstraße 26 · 29223 Celle · GERMANY · www.conmetallmeister.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>