hama 00118495 Monitor Holder Instruction Manual

June 12, 2024
Hama

hama 00118495 Monitor Holder Instruction Manual
hama 00118495 Monitor Holder

Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner

Explanation of warning symbols and notes

Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note
This symbol is used to indicate additional information or important notes.

Package contents

  • Monitor Arm
  • Mounting kit (see Fig. 1 for contents)
  • These operating instructions
    Mounting kit

Note
Please check the mounting kit for completeness before installing the product and ensure that there are no faulty or damaged parts.

Installation kit

  • (A1) M4x12 (x12)

  • (A2) M5x12 (x12)

  • (A3) D5 (x12)

  • (B1)M6x10 mm(x2)

  • (B2) M6x16mm (x3)

  • C (x5)

  • **(D1) (x3)

**

  • **(E) (x2)

**

  • **(F) (x4)

**

  • **(G) (x2)

**

  • (H1) 4mm (x1)

  • **(I) 6mm (x1)

**

Safety instructions

Warning

  • Given the multitude of terminal devices available on the market, the supplied mounting kit is unable to cover every option.
  • The screws for attaching the terminal device to the product may occasionally be too long.
  • Read the operating instructions for your terminal device before attempting to mount it. The instructions provide information about the type and measurements of suitable fastening materials.
  • If the supplied mounting kit does not contain suitable fastening materials for mounting the terminal device, purchase these from a specialised dealer.
  • Never apply force during assembly. This can damage your device or the product.
  • If in doubt, have this product mounted by a qualified technician – do not attempt to mount it yourself!

Note – Commercial use

  • If the device is used commercially, increased duty of care requirements apply.
  • Therefore, please observe the accident prevention regulations of the German employer’s liability insurance association for electrical systems and equipment. Please also observe all accident prevention regulations from other applicable employer’s liability insurance associations and accident insurance companies, as well as any legal regulations applicable to the particular industry and/or location.
  • The bracket must be installed by trained personnel or by a special technician, especially when installed in schools, educational institutions, hobby/self-service workshops or other publicly accessible institutions.
  • Have trained personnel carry out regular inspections to ensure that the product is securely installed, properly functioning and in acceptable condition (we recommend inspections at least every 6 months, or more frequently if required for the particular location) and then document these inspections.
  • Once you have mounted the product and the attached load, check that they are sufficiently secure and safe to use.
  • You should repeat this check at regular intervals (at least every three months).
  • Ensure that the product does not exceed its maximum permitted carrying capacity and that no load exceeding the maximum permitted dimensions is attached.
  • Make sure that the product is loaded symmetrically.
  • During adjustment, ensure that the product is loaded symmetrically and that the maximum permitted carrying capacity is not exceeded.
  • In the event of damage to the product, remove the attached load and stop using the product.
  • Mount the product only on tabletops with a sufficient load-bearing capacity and stability for the product and the device attached to it.
  • Ensure that the thickness of the tabletop is 1 – 8.8 cm.
  • Do not attach any additional objects to the product.
  • Keep the packaging material out of the reach of children due to the risk of suffocation.
  • Dispose of packaging material immediately in accordance with the locally applicable regulations.
  • Note that the product can cause pressure marks on the surface of the table. This depends on the weight loading and on the stability of the surface at the place of installation.

Application and specifications

  • The product is intended only for use inside buildings.
  • Use the product only for the intended purpose.

Maximum load: 7kg
Screen diagonal: 33 – 69 cm (13″– 27″)
Rotation: 360°
Tilt: -/+ 25° (device-dependent)
Swivel range: up to 180° on 3 joints (device-dependent)
Holder: up to 100 x 100, according to VESA standards

Preparation and assembly

Note

  • The product must be mounted by two people. Seek assistance and help!
  • Different end devices have different connections for cabling and other devices. Before commencing the installation, check whether the necessary connections can still be reached after mounting.
  • Depending on the product and mounting method, you may not need all parts of the mounting kit. It is therefore possible that unneeded screws and other small parts will be left over even after correct mounting. Keep these in a safe place together with the instructions for use for later reference (sale of the product, moving house).
  • Observe the other warnings and safety instructions.
  • Proceed step-for-step in accordance with the illustrated installation instructions ( Fig. 1a et seq. ).
    Preparation and assembly

Note

  • Given the multitude of terminal devices structures available on the market, we cannot describe all possible mounting options here.
  • lease ensure that the bracket lays flat and evenly on the back of the monitor.
  • Ensure that all screws have the proper length and can be mounted until they are hand-tight (see Fig. 3).
    Preparation and assembly
    Preparation and assembly
    Preparation and assembly

Adjustment & maintenance

Note – Height adjustment

  • The bracket must be adjusted by two people! Seek assistance and help!
  • During adjustment, ensure that the product is loaded symmetrically and that the maximum permitted carrying capacity is not exceeded.

Note – Setting/adjusting the tilt angle

  • To permanently set the tilt angle, loosen the fastening screws at the side, set the desired tilt angle and then tighten the screws again (see Fig. 7a).
  • In order to be able to flexibly adjust the tilt angle, turn the screws hand-tight only. In this way, the screen can be adjusted at any time.
  • No screws need to be loosened for the sideways movement.
  • Please only swivel the monitor arm within the range indicated (Fig. 6).
  • Once you have mounted the product and the attached load, check that they are sufficiently secure and safe to use.
  • You should repeat this check at regular intervals (at least every three months).
  • Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
    Adjustment & maintenance
    Adjustment & maintenance

Warranty disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Hama GmbH & Co KG
86652 Monheim/Germany

Service & Support

www.hama.com

+49 9091 502-0

Symbol
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.

hama logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals