CORNAT P6 Punto Wall-Mounted Single-Lever Sink Mixer Instruction Manual
- June 12, 2024
- CORNAT
Table of Contents
Instruction-manual / Warranty terms
The illustrations serve as visual depictions.
Product changes are possible. Subject to change.
Instruction-manual:
Please note the following points before installation:
– Installation should only be performed by experienced technicians under the
consideration of DIN1988 and VOB.
– Before starting the installation, please stop the water supply (ideally
close the main valve at the water meter).
– Please make sure that during assembly all seals fit properly (Always check –
water damage possible)
– The fitting is suitable for use in private households and only in rooms with
a temperature above 0 ° C. If there are a risk of frost, the water supply
should be interrupted and the valve must be completely emptied.
– Always before the first use and when a fitting has not been used for a
prolonged period, you should let rinse out a larger amount of water (water
stagnation) before drinking water is taken!
– Important MOUNTING Note:
The flexible connection hoses may only be hand screwed into the fitting. Do
not use under any circumstances tools like pliers or wrenches.
Operating conditions:
| Hot water temperature | max. 80 ° Celsius |
|---|---|
| Test pressure | max. 16 bar |
| Operating pressure | max. 10 bar |
| Holding pressure for shower conversion | min. 0.8 bar |
Care instructions:
Sanitary taps require special care. Please note the following information:
Chrome surfaces:
are sensitive for chemicals, acid-containing cleaning supplies and all kinds
of abrasives.
Occasionally clean with soapy water, using a soft cloth. Remove lime deposits
with household vinegar.
Gilded surfaces:
are particularly sensitive to abrasives.
Clean as chrome surfaces. Light polishing with a silver polishing cloth
brigthens.
Colored surfaces:
The surfaces of these taps are sealed with a special baking varnish. Do not
clean with abrasive, corrosive or cleaners containing alcohol.
Clean only with cold water and a soft cloth or leather.
Surface damages can be expected especially in gilded and colored fittings for
inobservance of care instructions. Warranty claims will not be asserted.
Hot water
Cold Water
The illustrations serve as
visual depictions.
Product changes are possible. Subject to change.
Warranty terms of Conmetall Meister GmbH
We guarantee the proper functioning of our products for a period, which is
shown on a Guarantee Logo applied on the products and / or the outer
packaging. If you think the product is defect, please check in advance whether
other reasons such as mishandling could be the cause.
In case of warranty, please contact first the trade partner from whom you
purchased the product.
This will contact us, the Conmetall Meister GmbH in doubt.
Please share exactly as possible which error / failure / damage / lack of
article is existent.
I. beginning of Conmetall Meister guarantee is the date of purchase of the
article.
II. Proof of Conmetall Meister guarantee is the sales receipt / invoice.
III. Subject of Conmetall Meister guarantee is the flawless function of the
article.
IV. The Conmetall Meister guarantee logo shows the duration of Conmetall
Meister warranty.
Defects must be reported during the period of warranty immediately after occurrence. The rejected article must be stored. For consequential damages the company Conmetall Meister is given the possibility, if appropriate, to assess the damage and the damage site case within 30 days prior to the repair.
The following cases are excluded:
- Typical wear and / or abrasion.
- Improper installation and / or commissioning.
- Improper handling and / or use.
- Tampering and / or repair.
Regardless of the Conmetall Meister guarantee, which is applied to the
products and / or the outer packaging, the instructions must be observed and
the instruction manual must be read carefully and stored.
The legal warranty rights exist irrespective of the Conmetall Meister
guarantee which is printed on the product and / or the outer packaging and
remain in an eventual exclusion of Conmetall Meister guarantee.
The Conmetall Meister guarantee granted by:
Conmetall Meister GmbH, Hafenstraße 26, 29223 Celle.
Sealing element
YA
Conmetall Meister GmbH
• Hafenstraße 26
• 29223 Celle
• GERMANY
•www.conmetallmeister.de
09/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>