CORNAT SP-EHM Kitchen Sink Tap Instruction Manual

CORNAT SP-EHM Kitchen Sink Tap

Intended use

• The product is a water-saving tap intended exclusively for connection to the cold water pipe and a power line to regulate the heating of the water and for installation on a sink/ washbasin. Ensure that the specifications for power connection and water pressure (see “technical data”) are followed.
• The product is not suitable for, and must not be connected to, central heating systems, instantaneous water heaters, pressure boilers, low-pressure water heaters or other water heating systems. If in doubt, consult a plumber or specialist advisor.
• Any use other than described above or modification of the product is not permitted and may result in damage. In addition, life-threatening hazards and injuries may result from improper use. The product is intended for private use only. The manufacturer accepts no liability for damage caused by improper use.

Instruction-manual

Please note the following points before installation:

• The installation should only be carried out by qualified persons in accordance with DIN1988.
• Before starting the installation, please tum off the water supply (ideally the main water tap at the water meter).
• water damage is possible)
• If the mains cable of this unit is damaged, it must be replaced by the manufacturer or its customer service or a similarly qualified person in order to avoid hazards.
• Only connect the unit to a cold water supply! Forquestions or uncertainties, contact a sanitary specialist. The fitting is suitable for use in private households and exclusively in rooms with a temperature above 0 ° C only. If there is a risk of frost, the water supply must be interrupted and the fitting must be emptied of any remaining water.
  -Always drain a large amount of water before using the tap for the first time and if it has not been used for a long period of time!

Important assembly note

• CAUTION! Do not twist the connection hose and do not put it under tension.
• Remove the protective cap from the fastening thread, then unscrew the fastening nut and the two cable guide rings from the fitting thread.
• The fitting can be installed so that the power cable is laid below (Fig. 1 a-3a) or (Fig. 1 b- 3b) above the work surface (worktop/ sink).
• When laying below the worktop, please ensure that the hole in the worktop is large enough for the mains plug to fit through.
• The flexible connection hose may only be screwed into the fitting hand-tight.
• Do not use tools such as pliers or spanners.

Commissioning

• After commissioning, check all connections carefully for leaks.
• Check the operation of the fitting. To do this, turn the lever forwards.
• Only if there are no leaks, insert the mains plug into the socket.
• Caution : as the water flow (flow rate) increases, the temperature in the hot water area drops!

Set water temperature

When the lever is at an angle of approx. 45 ° to the main unit, the water flow is switched off. Turning the lever downwards increases the flow for cold water. Turning the lever upwards increases the flow for hot water. As the flow rate increases in the hot water section, the water temperature decreases. When the unit is operated in the hot water section, the display shows the water temperature. Electricity is only consumed during hot water production.
It is therefore not necessary to disconnect the mains plug to save electricity. Always disconnect the unit from the mains before cleaning/ maintenance and when not in use for a longer period of time.

Technical data

• Model number: LH-SH-1
• Power supply: 220 -240 V – AC, 50/60 Hz
• Power consumption: 3600 W
• Protection class I
• Protection class IPX4
• Power connection: socket with a 16 A fuse
• Cable: 1500 mm
• Connection flex. Connection hose: 3/8″ – 1/2
• Flow rate: 2.5 I to 6 I (1.5 bar -5 bar / 150 -500 kPa)Max. water temperature: -55 °c
• Minimum flow pressure: 1.5 bar
• Total weight: 1,165 g

Care instructions

Sanitary fittings require special care. Please observe the following instructions:
Chrome-plated surfaces are sensitive to lime-dissolving agents, acidic cleaning agents and all types of scouring agents.
In case of light soiling, clean with soapy water and polish with a soft cloth. Remove limescale with household vinegar.
Failure to observe the care instructions may result in surface damage, especially to coloured fittings. Warranty claims cannot be made in this case.

SYMBOL

• Observe the notes in the operating instructions.

• Warning of electric shock! Danger to life!

• The tap corresponds to protection class I. Protection class I designates equipment with a protective earth connection. Devices with this protection class must have a protective earth conductor connected to the housing.
  This protective conductor is connected to the equipotential bonding of the electrical installation and connects the product to the earth potential.

• Splash-proof

• Products marked with this symbol comply with all applicable Community regulations of the European Economic Area.

• The SGS seal confirms that the product is safe when used as intended. The “GS” symbol stands for tested safety. Products marked with this symbol comply with the requirements of the German Product Safety Act (ProdSG).

• Dispose of the product and packaging in an environmentally friendly manner.

Safety instructions

KEEP ALL SAFETY INSTRUCTIONS AND DIRECTIONS FOR FUTURE REFERENCE. DANGER TO LIFE AND ACCIDENTS FOR TODDLERS AND CHILDREN!
Never leave children unsupervised with the packaging material. There is a danger of suffocation from packaging material.
Children often underestimate the dangers. Always keep children away from the product. This product can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children must not play with the product. Cleaning and user maintenance must not be carried out by children without supervision.

CAUTION AGAINST ELECTRIC SHOCK!
Leakage or water leakage can cause danger to life due to electric shock. Carefully check all connections for leaks and ensure that all cables from electrical appliances near the sink are correctly and safely installed. The connection plug of the fitting must fit into the socket. The plug must not be modified in any way. Do not use adapter plugs. Unmodified plugs and matching sockets reduce the risk of electric shock. Avoid contact with earthed surfaces such as pipes, heaters, cookers and refrigerators. There is an increased risk of electric shock if your body is earthed. Never immerse the connecting cable or the fitting in water or other liquids and ensure that they do not fall into the water. Never touch the power cable with wet hands when it is connected to the mains. Do not misuse the cable to pull the mains plug out of the socket or similar. Keep the cable away from heat, oil, sharp edges or moving parts of the appliance. Damaged or tangled cables increase the risk of electric shock. If in doubt, consult a qualified electrician.

CAUTION! DAMAGE TO PROPERTY!

• Improper installation and handling of the product can cause damage to property. Have the installation carried out by a specialist. Turn off the water supply to your living space before installation. During installation, make sure that all seals are correctly positioned on the sealing surfaces. Do not use the tap on low-pressure and small electric water heaters or other water heating systems. Only connect the fitting to cold water pipes. Use the product only at an ambient temperature above o 0c. Do not use the product
• if there is a risk that the water in the tap is frozen. If there is a risk of frost, interrupt the water supply and empty the fitting. Do not use the product if it is damaged or if its operation is impaired. Leaks and water leakage can cause considerable damage to buildings and household contents. Therefore, check all connections carefully for leaks. Before installation, familiarise yourself with all the conditions on site, e.g. the existing water connections and the shut-off devices. Do not make any changes to the unit!
• Do not change the connection lines yourself. Do not carry out repairs yourself, but commission a specialist or contact customer service in order to avoid hazards. Only have defective parts replaced with original spare parts.

Troubleshooting:

• If the appliance does not work properly, check if the problem can be solved by yourself. If the following steps do not solve the problem, please contact a specialist:

• The water flow has become weaker:

• The filter in the outlet pipe (see fig. 9a) or in the threaded pipe (see fig. 10) is dirty.

  • + Please clean as described in the chapter “Maintenance” (page 7).

• The water does not get warm:
  The mains plug is not inserted correctly into the socket.

  • Correct the fit of the mains plug The socket is defective.
  • Try a different socket There is no mains voltage.
  • Check the fuse of the electrical distributor (fuse box)

• The water is lukewarm:
  The greater the flow rate of the hot water, the cooler the water. + reduce the water flow by means of the lever

• The fuse in the fuse box has been tripped:
  Too many appliances connected in one circuit. + Reduce the number of connected devices
  The circuit is not designed for the power of the unit.

Disposal instructions

Disposal:

ATTENTION! usable do Electrical not and belong in the rechargeable household appliances waste! that are no A In accordance with the 2012/19 EU directive on WEEE (Waste – Electrical and Electronic Equipment), they must be collected separately and recycled in an environmentally friendly and professional manner. Please dispose of electrical equipment that is no longer usable at a local collection point. Collect packaging materials separately by type and dispose of them in accordance with local regulations.
For details, please contact your local authority.

Information requirements on the Electrical and Electronic Equipment Act 3:
The symbol of the crossed-out wheeled bin indicates that end-users are legally obliged to dispose this equipment separately from unsorted municipal waste, i.e. this waste equipment must be disposed sepa­rately from household waste. A bar under the waste bin means that the product was placed on the market after 13 August 2005.

Return option for old appliances: End users can return their old ap­pliances to the dealers/distributors. The dealers/distributors are obliged to take back old appliances free of charge. End-users are responsible for deleting the personal data on the product to be disposed of. Take-back and information obligations in trade: The already existing rules on the return of WEEE are specified as follows:

Obligation to take back exists for dealers/distributors Stationary trade:

• dealers with a sales area for electrical and electronic equipment of at least 400 square metres,
• food retailers/retailers with a total sales area of at least 800 square metres who offer electrical and electronic equipment several times a calendar year or on a permanent basis and make it available on the market

Online retail

• Online retailers with storage and shipping areas for electrical and electronic equipment of at least 400 square metres;
• Online grocery retailers with storage and shipping areas of at least 800 square metres.

Return options for small appliances
(edge length max. 25cm, up to 3 old appliances per type of appliance without new purchase):

• Stationary trade: directly in the retail shop;
• Online trade: return options in the immediate vicinity or return, so-called 0:1 take-back obligation

Return options for large appliances (edge length greater than 25cm):
– Stationary trade and online trade: Collection and disposal of large old appliances must be actively offered, when a new appliance is delivered to the door (“at the drop-off point”), it must be possible to return the old appliance, so-called 1 :1 take-back obligation.

Where applicable to the product, the following information is based on requirements of Regulations (EU) 812/2013 and (EU) 814/2013:

Instruction-manual

The illustrations serve as visual depictions.

maintenance

Warranty terms

Warranty Conditions for the Manufacturer Warranty of Conmetall Meister GmbH
The warranty below does not affect, and in particular does not re­strict or rule out, your statutory rights vis-a-vis the respective seller with regard to defects. These statutory rights exist irrespective of whether an event bringing the warranty into operation occurs or whether you assert rights based on the warranty below.
We guarantee that the item you have purchased and that has come with these warranty conditions will function without defects and be free of defects in materials and/or workmanship and of design flaws for the term of the warranty. This warranty commences on the date of purchase; the term of the warranty is shown in the warranty logo affixed to the item purchased. The start of the warranty must be documented by presenting the purchase receipt. If an event bringing the warranty into operation occurs and we repair the item in question or provide a new item as a re­placement, the term of the warranty is not extended as a result thereof.

There are no claims under this warranty if

• the item merely exhibits signs attributable to normal wear and tear,
• the item exhibits damage or signs of wear that are caused by use other than as normally intended and/or in deviation from the stipulations of the operating instructions,
• the item exhibits signs indicating that repairs or other interventions have been performed by unauthorized third parties, and/or
• accessories not authorized by us have been installed in the item or used with the item.
• Samples and display items are entirely excluded from this warranty.

To assert a claim under this warranty, you are required to show the item and the purchase receipt in the place where you purchased the item and turn them in there with as detailed and specific a description as possible of the event bringing the warranty into operation. The item will not be repaired or exchanged there. The item will be sent to us so we have a chance to examine it. If an event bringing the warranty into operation has occurred, we are free to choose whether to repair the item or replace ii with a new item. You have no claims beyond that under this warranty. If no event bringing the warranty into operation has occurred, the item will be sent back to you directly. We will notity you of this beforehand and, if possible, offer to perform a paid repair and provide you with
a cost estimate. If you decline to have the item repaired, or if we do not hear from you within 14 calendar days after transmitting the cost estimate to you, the item will be sent back. This warranty is only valid for items purchased in the Federal Republic of Germany and only where a return address located in the Federal Repub­lic of Germany is stated. The warranty itself is governed by the laws of the Federal Republic of Germany, to the exclusion of the United Nations Convention on Contracts for the International Sale of Goods (CISG).
The guarantor is Conmetall Meister GmbH, Hafenstrasse 26, 29223 Celle, Germany.
17.08.2017

Conmetall Meister GmbH • HafenstraBe 26 • 29223 Celle• GERMANY• www.conmetallmeister.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>