SWIT GA-PT20E DMX Motorized Pantograph Support System User Manual

SWIT GA-PT20E DMX Motorized Pantograph Support System

Important Notes

• Do not disassemble the product casually to avoid damage.
• Avoid using the product outdoors in rainy or snowy weather or in damp environments.
• Ensure the hinge is completely tightened during installation.
• When using DMX control, ensure there is a load at the lower end of the hinge to prevent motor damage.

FAQ

• Q: Can this product be used outdoors?
• A: It is not recommended to use this product outdoors in rainy or snowy weather or in damp environments as it may lead to damage.
• Q: What is the load range for this product?
• A: The load range for this product is 2kg to 30kg.
• Q: How should I connect the electric hinge to the luminaire?
• A: Install the luminaire correctly at the lower end of the hinge using appropriate connectors based on the luminaire type. Secure the luminaire power cord in the cable fixing groove behind the hinge and connect the power supply and DMX signal line for height adjustment.

Thank you for choosing SWIT products, please read the instructions before using them and keep them for future reference.

Technical Specifications

output)
Operating Mode| DMX512 signal control
Stretching Speed| 10cm/s
Stretching Length| 0.5m~2m| 0.6m~3m| 0.7m~4m| 0.8m~5m
Motor Power| Lifting motor power 60W
Motor Drive Voltage| DC 24V
Service Life| 10000 Lifts
Load Range| 2~30kg
Hinge Weight| 7.5KG| 8.5KG| 10KG| 12KG
Dimensions（mm）| 320150495| 320150585| 320150675| 320150765

Important Notes

1. Do not disassemble this product casually to avoid damage；
2. Do not use this product outdoors in rainy or snowy weather or place it in a damp environment；
3. During installation, ensure that the hinge is completely tightened. After confirming that all screws or accessories on the hinge are secure, install the lamp correctly at the lower end of the hinge；
4. When using DMX control for the hinge, there must be a load at the lower end of the hinge to prevent damage to the motor.

Appearance

1. Up button
2. Function button
3. Down button
4. Power Input
5. DMX Signal Input
6. DMX Signal Output
7. Power output

Installation Steps

Secure the Electric Hinge (Installation Method — Hanging with Lamp Hook)
Connect the thread mouth at the top of the electric hinge with the lamp hook (the top connection can be disassembled to connect the lamp hook). Fix the lamp hook and lamp grille to secure the top of the electric constant force hinge extender outside the track to complete the suspension.
Note: Keep the hinge naturally vertical during installation

Connect the Electric Hinge to the Luminaire
Install the luminaire correctly at the lower end of the hinge, and the lower end of the electric hinge is equipped with a tube-type interface.

1. If the luminaire is mounted with a U-shaped bracket, fix one end of the lamp handle screw with a nut on the luminaire’s U-shaped bracket. Use a connecting screw to secure the other end to the tube-type interface；
2. If the luminaire is mounted with a rod-controlled lamp bow, directly use a connecting screw to fix the top to the tube-type interface.

Cable fixing

• Secure the luminaire power cord correctly in the cable fixing groove behind the hinge and fasten it with zip ties.
• Connect the power supply and DMX signal line of the hinge to control the height adjustment of the luminaire

Instructions for using

The front panel of the Pantograph is equipped with DMX address code settings:

1. Press the “SET” button for 3 seconds to enter the address code setting. Use the increase/decrease keys to adjust the address, then press the “SET” button to save；
2. Press the “SET” button for 6 seconds to enter the protection limit setting interface. Press the “SET” button to switch, sequentially entering: 1H lifting motor descent value, 1U lifting motor ascent value. Use the increase/decrease keys to adjust and press the “SET” button to save.

Users can set the address code as needed. After setting, the hinge can be controlled for up and down stretching through the DMX512 lighting console, achieving precise positioning of the luminaire.

Packing List

CONTACT

• Tel: 025-85805753
• Fax: 025-85805296
• http://www.swit.cc
• E-mail: Contact@swit.cc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>