PXN 9607X Wireless Controller for Nintendo Switch-Lite-OLED Extra Controller Instructions
- June 5, 2024
- PXN
Table of Contents
PXN 9607X Wireless Controller for Nintendo Switch-Lite-OLED Extra
Controller
Product use instructions
summarize
The Bluetooth controller with vibration is specially designed for the
SWITCH platform.Compatible with PC/ android platform。
Functional Characteristics
- Bluetooth 5.0
- Compatible with the SWITCH host platform, PC platform
- Low power mode (disconnect after sleep)
- SWITCH host platform has a sensor induction function
- With double motor vibration function
- The linear transmission distance is over 10 meters
- Built-in lithium battery 3.7v, can be used for more than 20 hours
- can be charged via TYPE-C USB
Product diagram
instructions
The first step is to turn on the cable Settings in the host as shown
below
POWER ON/OFF
POWER ON：
Press the “HOME” button for 3 seconds to activate the controller, and the four
LED racing flashes once per second
POWER OFF：
Press the “HOME” button for 1 second to close the controller。 4.3 connect：
SWITCH host press and hold the “Y” button and then press the “HOME” button to
start up the pairing, four LED racing flashing,1 second 2 times, connected to
the current LED light long bright.(LED1 is bright if it is the first machine
connection, and LED2 is bright if it is the second, and so on) The android
platform, press A and press HOME again. LED2+LED3 Quick flashing, LED2+LaED3
lights up after successful connection. Connect the gamepad to the computer
with the USB Micro data cable, which is the x-input key-value gamepad.
Low power prompt：
The current connection light flashes twice per second. Charging in the
connected state of the handle: the light in the current mode of the charging
line will flash slowly for 1 second and light up normally when fully charged.
Disconnect charging： Insert the charging cable, four LED lights flash once
every 1 second, and four LED lights go out when full.
Controller sleep function ：
4Press the “HOME” button to start up the handle in the reconnecting state, and
no signal will be received for 10 seconds to enter sleep.After connecting the
Controller, there will be no keystroke or axis movement for 5 minutes to sleep
Calibration of the Controller： When the Controlle is off, press the -button, B
button and HOME button at the same time. The four LEDs of the Controlle are
divided into two groups to shine alternately. The Controlle is placed on the
leds of the Controlle are divided into two groups to shine alternately. The
Controller is placed on the horizontal desktop and then press the + button.
Other parameter
- Search for current：18-26MA
- Working current：26MA
- Low power alarm：3.5V
- Shutdown voltage：3.2V
- Sleep current： Less than 50uA
NO.| button| SWITCH code| PC X-INPUT
code
| | Android code|
---|---|---|---|---|---|---
1| A| A| B| 97
2| B| B| A| 96
3| X| X| Y| 100
4| Y| Y| X| 99
5| L| L| LB| 102
6| R| R| RB| 103
7| –| –| BACK| 109
8| +| +| START| 108
9| 0| screenshots| NO| NO
10| 3D press L| 3D press L| Thumb L| 106
11| 3D press R| 3D press R| Thumb R| 107
12| Z L| Z L| LT| 104
13| Z R| Z R| RT| 105
14| ML-> X (3D VR)| ML-> X (3D VR)| ML-> X (3D VR)| ML-> X (3D VR)
---|---|---|---|---
15| ML-> Y (3D VR)| ML-> Y (3D VR)| ML-> Y (3D VR)| ML-> Y (3D VR)
16| MR- >X (3D VR)| MR- >X (3D VR)| MR- >X (3D VR)| MR- >X (3D VR)
17| MR ->Y (3D VR)| MR ->Y (3D VR)| MR ->Y (3D VR)| MR ->Y (3D VR)
18| D-PAD-UP| D-PAD- UP| D-PAD- UP| 19
19| D-PAD-DOWN| D-PAD- DOWN| D-PAD- DOWN| 20
20| D-PAD-LEFT| D-PAD- LEFT| D-PAD- LEFT| 21
21| D-PAD-RIGHT| D-PAD- RIGHT| D-PAD- RIGHT| 22
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including
interference that may cause undesired operation.
Caution:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant t part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference e in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. How
ever, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
o n, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help with an important announcement
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>