Thmosz RJD 1.2 Cuft Fireproof Safe Box Instruction Manual

ELECTRONIC SAFE BOX(RJD)
INSTRUCTION MANUAL

RJD 1.2 Cuft Fireproof Safe Box

Please do not keep emergency keys in your safe ! ! !
Dear valued customer :
Thank you for choosing our products! You’ve taken an important step in organizing and protecting your most valued possessions. Every Series of our safes is professionally made and designed to provide safety. Please take time to read  and familiarize yourself with the proper operating procedures of your new safe presented on the following pages.
Again, thank you for choosing our products!

CONTACT US:

If there is any problem about your item, please contact us with order number and product pictures through the following email, we will offer you help.
Email : service@nicesafebox.com

PRODUCT DESCRIPTION

Product List

1 : Digital Keypad| 2 : Connection hole for battery
3 : Hidden Keyhole| 4 : LCD Display
5 : Battery Compartment (on the inside)| 6 : Bolts

• The connection hole for battery on the side of the keypad is designed for external power supply, in case the key is lost and the Internal battery dies.

BEFORE FIRST USE

CAUTION :

• Risk of suffocation!
• Keep any packaging materials away from children and pets-these materials are a potential source of danger, e.g. suffocation.
• Remove all the packing materials.
• Remove and review all components before use.
• Check the product for transport damages.

OPENING THE SAFE IN EMERGENCY

Use an emergency key to open the door :

• when you have forgotten your code;

• when the keypad is disabled after 3 wrong codes have been entered in a row;

• when the batteries have been exhausted.
  ****CAUTION :

• The emergency key can only be taken out after turning counterclockwise to the lock position.

• Do not forcibly pull the emergency key out.

• The emergency key can only be used to lock if this was also used to unlock the door earlier.

POWER SUPPLY

Inserting Batteries:

1. Use the emergency key to unlock the door.
2. Lift the cover of the battery compartment off while pressing the release latch.
3. Insert 4 x AA batteries into the battery compartment. Refit the cover (Fig. 2).
4. Use the emergency key to lock the door.

CAUTION :

• The batteries are not included ! ! !
• The working voltage for the product is equal to 4 x AA batteries.
• Always insert batteries correctly with regards to polarity ( + and – ) marked on the battery and the product.
• Exhausted batteries should be immediately removed from product and properly disposed.
• System will turn into micro power consuming state automatically.

USING PERSONAL CODE TO OPEN THE SAFE

• Input your 3 to 6 digit number then the word ” OPENED ” appears and the safe will be open.
  ****CAUTION :

• When you receive the safe box, it is not locked.

• Please set your personal code before the safe box be first closed.

• Before closing the safe, enter the new code and make sure the safe can be opened.

• Press ” CLEAR ” key before entering code then the display will not show the numbers being entered nor the code being set.

CLOSING THE DOOR

• Press directly the ” LOCK ” key, the word ” CLOSED ” appears and the safe will be closed.

SETTING THE PERSONAL CODE

• Keep the door open, Press ” CLEAR ” and the display shows ” SET ” appears, then Input your 3 to 6 digit number + ” LOCK “, the display (F) shows ” GOOD “; which means the master code has been changed successfully.

• Press the ” LOCK ” key to close the door.
  ****CAUTION :

• Repeat the steps above if ” Error ” is shown on the display.

ALARM FUNCTION

• If the wrong code is entered 3 times continuously, the display will show ” HOLD-5 “. And the keyboard will be locked for 5 minutes.
• If the wrong code is entered, the display will show ” E-CODE ” and the buzzer will sound.
• When the entered password is incorrect, press ” CLEAR ” to delete.

CAUTION :

The keyboard would be disabled during the beeping. You can only stop the beeps by opening the safe with emergency key and power-cut by removing the battery.

MOUNTING

• Drill holes for expansion bolts (or clamping screws) in the right place;

• Turn the expansion bolts anticlockwise to separate;

• Use the expansion bolts (or clamping screws) to secure the case to the wall;

• Make sure the case is mounted in place as required and then tighten all screws.
  CAUTION :

• Use the expansion bolts when there is the concrete wall surface.

• Use the clamping screws when there is the wooden wall surface.

CUSTOMER SUPPORT

If you have the problem that is not answered in the FAQ section of this manual, please contact us with the order number and the product pictures through the following email. We will offer you help. We encourage you to email us:
service@nicesafebox.com

Please prepare the following information available when contacting us:

• Purchaser’s name and mailing address, e-mail address, and phone number.
• Online order number.
• Detailed description of the problem.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>