Breville BBL820 Commercial Grade High Performance Blender Juicer Instruction Manual

Breville BBL820 Commercial Grade High Performance Blender Juicer

IMPORTANT SAFEGUARDS FOR ALL ELECTRICAL APPLIANCES
READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

BREVILLE® RECOMMENDSSAFETY FIRST
At Breville® we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition, we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE

• Remove and discard all packaging materials and stickers before first use.

• To avoid choking hazards for young children, remove and safely dispose of the protective cover fitted on the power plug.

• This appliance is for household use only. Do not use it in moving vehicles or boats, do not use it outdoors, and do not use it for anything other than its intended use. Misuse can cause injury.

• This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.

• Cleaning and user maintenance shall not be done by children without supervision.

• Children shall not play with this appliance.

• This appliance can be used by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.

• Do not use the appliance near the edge of a countertop or table. Ensure the surface is level, clean, and free of water and other substances. Please be aware that vibration during use may cause the appliance to move.

• Do not use the appliance on (or close to) a hot gas or electric burner, or where it could touch a heated oven or surface.

• Do not allow the cord to hang over the edge of a countertop, or to become knotted.

• To avoid electric shock, do not immerse the cord, plug, or motor base in water (or other liquids).

• Installation of a residual current device (a standard safety switch on your wall socket) is recommended to provide additional safety protection when using appliances. A safety switch (with

• a rated residual operating current not more than 30mA) should be installed in the electrical circuit supplying the appliance. Contact your electrician for further professional advice.

• In order to avoid the possible hazard of the blender starting by itself due to inadvertent resetting of the overload protector on the motor, do not attach an external switching device (such as a timer) or connect the blender to a circuit that can regularly switch
  the blender on and off.

• Do not operate the appliance with a damaged cord or plug, or after the appliance malfunctions, or if dropped or damaged in any way. Stop use immediately and contact Breville® by phone or email for replacement or repair.

• All maintenance (other than cleaning) is to be done by an authorized Breville® Service Centre.

SAFEGUARDS FOR YOUR BLENDER

• Wash the blender jug with warm soapy water before first use.

• Use only the blender jug and lid that is supplied with this blender. The use of attachments, including canning jars or accessories not manufactured or specified by Breville® may cause the risk of fire, electrical shock, or injury.

• Always ensure the blender is assembled properly before using it. The lid must be firmly secured to the jug before the operation to ensure internal contents do not escape, spray or overflow.

• Always ensure the appliance is properly assembled as per instructions before use. Using the appliance without being properly assembled may cause product malfunction, product damage or pose safety risk including personal injury.

• If the motor is straining under a heavy load, do not operate continuously for more than 10 seconds. Allow the motor to rest for 1 minute between uses on heavy loads. Note that none of the recipes in these instructions are considered a heavy load.

• Do not leave the blender unattended when in use.

• The flashing light indicates ready to operate. Avoid any contact with blades or moving parts.

• Keep hands, fingers, hair, and clothing away from the blender during use. Always turn the blender off and unplug from the wall before reaching inside.

• Be careful when handling the blender jug as the blades are very sharp. Be careful when emptying the jug and during cleaning. Mishandling of the blades may cause injury.

• Do not remove the jug from the motor base while the blender is in use.

• The blender is intended for food or drink preparation. Do not use it for anything other than food or drinks. Do not operate without any ingredients in the blender jug.

• Never attempt to operate with damaged blades, or with utensils, or any foreign objects inside the blender jug.

• To reduce the risk of severe injury to persons or damage to the blender, keep hands and utensils out of the jug while blending. The scraper and frozen dessert tamper provided can be used, provided the main lid is in place.

• Be careful if hot liquid is poured into the blender, as it can be ejected out of the jug due to sudden steaming.

• When blending hot liquids ensure the inner measuring cap is in place. Cap will protect from splashing of hot liquids during blending and includes vents designed to relieve pressure and avoid steam build up.

• Be careful removing the
  lid after blending hot liquids, as steam traps can form in the liquid and be ejected out of the jug.

• Do not put the blender jug in extremes of heat or cold, for example placing a cold jug into hot water, or vice versa.

• Before moving the blender, cleaning, or putting it away for storage, always turn the blender off and unplug it from the wall.

• Strictly observe the reduced capacity limit for blending hot ingredients. Failing
  to follow this instruction may cause personal injury by hot liquid burn.

• Never blend hot ingredients/liquids using the vacuum blending feature. (Vacuum blending is an optional feature achieved through using the Breville® vacuum pump supplied separately.)

• Never use attachments or accessories that are not supplied with this product or authorized by Breville® to be used on this product. Failing to follow this instruction may cause product malfunction, product damage, or even pose a safety risk.

• For optional accessories authorized by Breville® to be used on this product, please read all instructions supplied with the accessory in conjunction with the instructions contained in this booklet.

FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS

Components

• A. Inner measuring cup
  Removable for quick addition of ingredients.

• B. High-performance lid
  Withstands high-velocity tasks, and is designed to vent steam and prevent splatter.

• *C. 2.0 Litre BPA-Free jug**
  Impact resistant, shatter proof and dishwasher safe.

• D. Extra-wide, heavy-duty blade and   bowl system
  Designed with 4 powerful stainless steel blades contoured to the base of the jug for maximum cutting power and processing results including liquid-free processing.

• E. Heavy-duty metal coupling
  For durable and long-lasting performance under demanding conditions.

• F. Heavy duty motor
  High-velocity power combined with high torque for outstanding results.

• G. LCD indicator with timer
  Counts down for pre-programmed settings, and counts up for speed dial settings.

• H. Durable base

• I. 4 preset programs
  Optimize the blender’s capabilities for crushing ice, smoothies, green smoothies, and soups.

• J. 5-speed settings
  The wide speed range for convenient speed selection.

• K. Overload protection
  Resettable thermal fuse for motor protection.

ACCESSORIES

L. Tamper
Helps make frozen desserts, nut butter, and dips by pushing thick foods directly into the blades. Always use tamper with the blender lid on (inner cap removed).

COPOLYESTER MATERIAL
This blender jug is made with copolyester, which is a tough, BPA-free polymer used to make housewares products that can stand up to extreme use and repeated dishwasher cleaning. Products made from copolyester are impact resistant and shatter-resistant and stay clear and durable even after hundreds of cycles in the dishwasher.

BREVILLE ASSIST™ PLUG
Your Breville® appliance comes with a unique Breville Assist™ Plug, conveniently designed with a finger hole for easy removal from the wall outlet

Functions

GETTING STARTED

Ready mode
Press the ON | OFF button to power the unit to READY mode.

Sleep

• After 2 minutes of inactivity, the LCD powers off, and the ON | OFF button flashes red.
• After 5 minutes of inactivity, the blender turns power OFF. Press the ON | OFF button to reactivate the blender.

CANCEL
The CANCEL function stops the pre-set program or selected speed setting and sets the time to 0.

Speed Control Selection

• There are 5 electronic speed buttons from MIX through to MILL.
• MIX combines more delicate foods with a folding motion and is good for combining wet and dry ingredients.
• MILL is the fastest setting and is ideal for breaking down ingredients to mill grain to flour, make nut milk and other finely blended mixtures.
• Select the required speed (1 to 5) by pressing the corresponding speed button.

WARNING: Never blend boiling liquids. Allow the temperature of ingredients to cool down to room temperature before placing them into a blender jug.

PRESET PROGRAMS

PULSE | ICE CRUSH
A program of continuous pulsing designed to chop food into an even consistency or crush ice cubes.

SMOOTHIE
For dairy-based smoothies. A combination of speeds and pulses is designed to combine and aerate ingredients into a smooth and creamy texture.

GREEN SMOOTHIE
For blending whole fruits/vegetables into a smooth beverage. A combination of high-speed profiles breaks down tough fibres into very fine particles. Use the tamper if ingredients become wedged.

SOUP
This program is exclusively for creating a cold-to-hot soup–turning whole ingredients at ambient temperature into a smooth,hot soup. Primarily a high- speed program, the program will finish with a slow stir to remove steam bubbles.

NOTE: Raw foods such as meats and seafood need to be cooked prior to using the SOUP program.

WARNING: Do not add hot ingredients when using the SOUP program.
If the blender is running and you press a different preset button, it will switch to that program without stopping. If a program is running and you press the same program button again, it will pause that program and timer. To resume press the same program button again.

CLEAN: Use to remove most of the ingredients of the blender walls and blades. Add 4 cups of warm soapy water to the blender jug and press the CLEAN button. For harder-to-clean, sticky or thick ingredients, add ½ teaspoon of liquid dish detergent for extra cleaning power. For best results, clean the blender jug this way immediately after use.

Tips

• The inner measuring cap can be removed and oils/liquids or other ingredients added during blending. Extreme care must be taken as depending on the mixture and speeds of operation, splashes can eject from the Lid.
  It is not suggested to remove the inner measuring cap when blending hot liquids.

• Do not exceed the maximum mark when adding foods and liquids into the blender.

• Run the blender only for the appropriate amount of time required – do not over-blend ingredients.

• Use the PULSE | ICE CRUSH button when food is too thick or coarse to circulate within the blender jug.

• The tamper accessory can be used during blending by removing the inner measuring cap. Always make sure the main lid stays firmly in place.

• Ingredients may stick to the sides of the blender jug. To push food back onto the blades with the main lid on (inner cap removed), use the tamper provided to scrape down the sides of the jug, and continue blending.

• If any moisture or liquid spills on top of the motor base during blending, turn the blender off and unplug from the outlet. Remove the blender jug, and wipe the motor base immediately with a dry cloth or paper towel.

• The optimum amount of ice cubes that the blender can process in the jug is 250g
  (approximately 1 standard ice tray).

• Thicker mixtures puree more efficiently if the jug is ¼ to ½ full.

• Do not use metal utensils, as they may damage the blades or blender jug.

• Dates and other dried fruits may vary in hardness and moisture content. If adding dried fruits to smoothies, use the tamper for the first 15–20 seconds of the SMOOTHIE or GREEN SMOOTHIE setting.

• To make nut milk, add 1–2 cups of raw or soaked/drained nuts. Add 3–4 cups of purified water, and process on MILL for 1 minute. Strain through a nut milk bag (or muslin/cheesecloth) over a large bowl or jug. Close the bag and squeeze the pulp in the bag to extract as much milk as you can.

• To soak or not to soak nuts? This is a personal preference and you can make nut milks with unsoaked or soaked almonds. Almonds are a great source of protein however they contain a naturally occurring compound that may prevent our enzymes from digesting the nuts effectively. Try soaking nuts overnight to help break down the compound. Always rinse and drain soaked nuts before use.

• Roasting nuts to make nut butter allows their natural oils to be released during blending, and enriches the flavour. Some nuts, such as almonds and hazelnuts, have a lower oil content. Add rice bran, macadamia or coconut oil when blending, if needed.

• Freshly milled whole grain flour does not keep as long as commercial flour. This is because the inner layers of the grain contain rich oils, which can become rancid over time with exposure to heat and moisture. Always store your flour in an airtight container in a cool, dry place. Flour can be stored in the refrigerator or freezer in warm/humid climates.

• Corn, soybeans, and some other dried legumes and grains vary in their moisture content, and may not circulate properly during milling. Use the scraper spatula or tamper during milling to assist with circulation.

• To remove any food that cannot easily be scraped out from under the blades, replace the lid and turn the blender back on high speed for 4–5 seconds to spin foods out from under the blades.

Blending Chart

Dry milling

• Please note that milling hard ingredients like spices, nuts, sugar, coffee, grains, etc will cause scratching and clouding to the inside surfaces of the jug.
• This is a cosmetic result of milling these kinds of ingredients and does not affect the performance of the jug.
• Avoid over-processing spices though. Essential oils found in spices when combined with heat can damage the jug surface

Troubleshooting

Care & Cleaning

Jug and Lid
To avoid food drying on blades, jug, and lid, follow the below steps as soon as possible after use:

• Rinse most of the ingredients off the jug and lid.
• Add 1L of warm water and 1–2 drops of detergent and press the CLEAN button.
• Rinse the jug and lid again and/or wash separately in warm soapy water with a soft cloth or bottle brush.

WARNING
Oils in citrus rind can damage the material of your jug if exposed to it for a longer period. Always clean your blender jug and personal blender cup immediately after processing the citrus rind.

Motor base
To clean the motor base, wipe with a soft, damp cloth then dry thoroughly. Wipe any excess food particles from the power cord.

Cleaning agents
Do not use abrasive scouring pads or cleaners on either the motor base or the jug, as they may scratch the surface. Use only warm soapy water with a soft cloth.

Dishwasher
The blender jug, tamper, and lid can be washed in the dishwasher on a standard wash cycle. The jug can be placed on the bottom shelf, however, the tamper should be on the top shelf only.

Stubborn food stains and odours
Strong-smelling foods such as garlic and fish, and some vegetables such as carrots, may leave an odor or stain.

2 Litre jug

• Remove, and clean the jug and lid using the CLEAN instructions. Add 2 tablespoons bicarbonate of soda and ½ cup (125mL) vinegar into jug and let the mixture froth for 1 minute. Scrub the jug and lid with the mixture using a soft dishwashing brush. Add 2 cups warm water and allow to stand for 5 minutes. Attach jug to blender base. Secure the lid and then press the CLEAN button. Thoroughly rinse the jug, and allow it to air dry. Store the jug and lid with the lid off to allow air to circulate.

Dry milling

• Milling hard ingredients like spices, nuts, sugar, coffee, grains, etc will cause scratching and clouding to the inside surfaces of the jug.
• Some spices and herbs release aromatic oils that may discolor the jug or leave an aroma.
• These are cosmetic results from milling these kinds of ingredients and do not affect the performance of the jug.

Storage
Store your blender upright with the blender jug assembled on the motor base, or beside it. Do not place anything on top. To allow air to circulate, keep the lid off.

Warranty

2 YEAR WARRANTY
Breville provides product warranty for domestic use in specified territories for 2 years from the date of purchase by faulty workmanship and materials. During this warranty period, Breville will provide repairs and replacement for any defective product (based on Breville’s Warranty Policy).

Also, all legal warranty rights under Korea’s legislation will be protected and will not be impaired by our warranty. For full terms and conditions on the warranty, as well as instructions on how to make a claim, please visit: www.breville.com/kr

Copyright Breville Pty. Ltd. 2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>