Burns Barkles 012682 LPG for Griddle Plate Instruction Manual

Burns Barkles 012682 LPG for Griddle Plate

SAFETY INSTRUCTIONS

• Only for outdoor
• Do not use the product near flammable
• Do not move the product when in
• Close the valve on the gas cylinder after
• Do not make any modifications to the
• Do not put the gas cylinder under or near the
• The storage of gas cylinders must comply with local Do not store gas cylinders under the product.
• Only use propane or butane that complies with the specifications in the
• Never use flammable liquid to light or re-light.
• Read these instructions carefully before Assemble the product according to these instructions. Do not replace any components. Failure to follow all the instructions and safety instructions can result in a risk of personal injury and/or material damage.
• Immediately turn off the gas supply in the gas cylinder in the event of leaking
• Check all gas hoses for damage, leakage and/or incorrect If it is not possible to stop the leakage, contact a service centre or allow an authorised gas technician to check the product. Never do a leakage test with a naked flame.
• Never disconnect gas connections or hoses when the product is in
• Never leave the product unattended when it is in Be careful when cooking food.
• Always turn off the gas tap on the gas cylinder after
• The product must be placed at least 1.5 metres from combustible material.
• Do not lean over the product when lighting it.
• Do use utensils made of plastic or glass to cook
• Check and clean the product Take care not to damage any components, such as burners or valves, when cleaning.
• Check all hoses at least once every year and every time the gas cylinder is replaced.
• Replace damaged hoses with new ones of the same quality and length as the original
• The product should be checked every year by an authorised service centre or other qualified Never attempt to service or repair the product yourself.
• Only use the product in a well ventilated
• Replace all hoses at least every other Follow national regulations concerning the replacement of hoses.
• Never break any seals on the
• Keep cables and hoses away from hot
• Be careful when cooking
• Never heat unopened containers made of glass or metal – they can burst and cause serious personal injury and/or material damage.
• Use oven gloves when handling hot
• Keep all ventilation of boiling burner always
• Check all burners before using, make sure no any blockage on
• Any modifications of this appliance may be dangerous and are not permitted.

WARNING

• Accessible parts can be
• Keep children away from the
• Wear safety gloves when handling hot
• Keep all ventilation of boiling burner always
• Check all burners before using, make sure no any blockage on

TECHNICAL DATA

Gas; supply pressure
Butane/propane 30 mbar
Butane/propane 37 mbar

Product category
I3B/P(30)
I3B/P(37)

Injector size
Outer ring: 1.3 mm
Inner ring: 1.0 mm

Tot. nom. heat output
I3B/P(30):12.0 kW / 872.6 g/h
I3B/P(37):12.5 kW / 909.0 g/h
Lighting     Integrated

Gas cylinder
Max height 590 mm
Max diameter 310 mm
Max content 10 kg

DESCRIPTION

1. Rim
2. Burner
3. Leg
4. Grille shelf
5. Screw M6x35
6. Nut M6
7. Screw M6x20

FIG. 1
FIG. 2

ASSEMBLY

See diagrams for correct assembly of the product.
FIG. 3
FIG. 4
FIG. 5

CONNECTING THE GAS CYLINDER
WARNING!

• Before connecting the gas cylinder, check that the coupling, regulator, burner and burner parts are in good
• If the hose is replaced it must be secured on the grill and the regulator connections with hose clips. Disconnect the regulator from the gas cylinder when the gas grill is not in
• Follow the instructions supplied with the regulator.

CONNECTING THE GAS CYLINDER

NOTE: Gas cylinder and regulator sold separately.

• Place the product on a level, stable Check that the inlet and outlet regulator suit the gas cylinder valve and the product.
• If the regulators are kept outdoors, protect them from precipitation,
• A spanner is needed to connect the gas
• Check that the hose is not clinched or twisted when
• Place the gas cylinder on the left side of the product, in a safe place protected from
• The hose diameter must be 8–10 The hose must not be longer than 1.5 m.

1. Gas connection
2. Hose
3. Gas cylinder
4. Gas regulator
5. Hose
   FIG. 6

LEAKAGE TEST

1. Mix 1 part of washing-up liquid/soap with 3 parts of water.
2. Check that the control knob is in the OFF position.
3. Connect the gas cylinder to the regulator, the regulator to the hose, and the hose to the Screw tight and open the gas valve.
4. Apply the soapy solution to the hose and on all the Bubbles indicate leakage, which must be fixed before the product is used.
5. Do a new leakage test after repairing the leak. Close the gas cylinder valve after the leakage
6. If a leakage cannot be fixed, contact an authorised service Do not attempt repairs yourself.

FIG. 7
FIG. 8

GAS CYLINDER

• Handle the gas cylinder with care and avoid knocking it. The gas cylinder must not be connected when the product is not in Replace the cap on the gas cylinder when the cylinder is disconnected from the product.
• Do not change gas cylinders near sources of
• The gas cylinder must be stored upright outdoors, out of the reach of Do not store the gas cylinder where the temperature can exceed 50°C. Do not store the gas cylinder near naked flames, pilot lights, or other sources of heat.

USE

LIGHTING

1. Check that all the control knobs are closed.
2. Connect the regulator to the gas cylinder the regulator to the hose, and the hose to the product.
3. Open the gas tap on the gas
4. Check with soapy water that there is no gas leakage between the gas cylinder and the
5. Press down and turn the control knob anticlockwise to HI (it will click).
6. Wait for several seconds, let the gas get into burner from the Then use the long match or BBQ lighter to light the burner.
7. Light the If the burner does not light, turn the control knob to closed position and wait 5 minutes before trying to light the grill again.
8. When the burner is lit, adjust the temperature by turning the control knob to HI or LO.
9. The burners can be used separately or The left-hand control knob controls the outer burner and the right- hand knob controls the inner burner.
10. To turn off the burner – turn the gas tap on the gas cylinder to the closed position, wait until the flame goes out, and then turn the control knob on the product to OFF.

FIG. 9

MAINTENANCE

Maintenance is recommended every 90 days for your boiling burner for outdoor use, but it is absolutely necessary to perform maintenance at least once a year. By doing so, you will extend the life of your boiling burner for outdoor use. Your boiling burner for outdoor use is easy to clean with minimum effort, just follow these helpful hints for cleaning convenience:

• Cleaning and maintenance should be carried out after use when the product has cooled and when the gas supply from the gas cylinder is turned off.
• Do not use aggressive detergents or oven cleaners on enamelled surfaces. Wash with a mild, non-abrasive detergent and hot soapy Wipe dry with a soft cloth.
• Do not use abrasive or flammable detergents, they can damage the product and are a fire

STORAGE

• Your gas cylinder must be stored outdoors in a well ventilated area and must be disconnected from your boiling burner for outdoor use when not in Ensure that you are outdoors and away from any sources of ignition before attempting to disconnect your gas cylinder from your boiling burner for outdoor use.
• When you are using your boiling burner for outdoor use after a period of storage, please ensure to check for gas leaks and check for any obstructions in the burner before using.
• If boiling burner for outdoor use is stored outdoors ensure to check that all areas under the front control box is free from any obstructions (dirt, insects etc.) as this may affect the flow of gas.
• Store your boiling burner for outdoor use in a cool dry It may be necessary to dry the boiling burner for outdoor use and the inside of the cover if used.

REFITTING THE BURNER

When refitting the burner, be careful to check that the venture tubes of the burner fit over the valve outlets. It is extremely important to center the burner on the orifice properly to prevent a fire hazard or explosion. When properly installed, all screws holding the burner in place will be able to screw in without force.

If the refit of the burner fails, please contact service center, and do not repair yourself.
After successfully refitting all burners, the leakage test should be performed. Please see “ LEAKAGE TEST SECTION”.
After leakage test, the light test should be also performed. Please see “LIGHTING SECTION”. Please note the burner lighting test should be done burner by burner.

FIG. 10

TROUBLESHOOTING

control knob.
The burner will not light.| No gas flow.| Check if the gas cylinder is empty.
The flame goes out.| Strong or gusty wind.| Put the product in a sheltered place, or increase the height of the flame.

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>