Eurofase 48101 30 X 22 Inch Black Wall Mirror Instruction Manual
- June 1, 2024
- EUROfase
Table of Contents
Eurofase 48101 30 X 22 Inch Black Wall Mirror
Product Information
Specifications:
- Model : Lenora
- Max Wattage : 30W
- Light Source : LED
- Voltage : 120V~, 60Hz
Product Usage Instructions
-
Unpacking and Setup:
Upon receiving the product, carefully unpack all components. Ensure all parts are included as per the manual. Place the lighting product in the desired location for installation. -
Installation:
Follow the provided installation instructions to securely mount the Lenora lighting product. Make sure to turn off the power source before proceeding with installation. -
Power Connection:
Connect the lighting product to a power source that matches the voltage requirements specified (120V~, 60Hz). Double-check all connections before turning on the power. -
Operation :
Use the designated switches or controls to turn the lighting product on/off or adjust brightness levels as needed. Refer to the user manual for specific operation details.
Thank You
You’ ‘ve just purchased a lighting product designed and built to provide you
with years of enjoyment.
IMPORTANT SAFETY INSTRUCTIONS
- Attention to installer, must test the light fixture before installation.
- When using an electrical furnishing, basic precautions should always be followed, including the following:
- Read all instructions before using (this furnishing).
- DANGER – To reduce the risk of electric shock: Always unplug this furnishing from the electrical outlet before cleaning or servicing.
- WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
- Unplug from outlet before putting on or taking off parts.
- Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
- Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this fumishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and repair.
- Keep the cord away from heated surfaces.
- Never operate the fumishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
- To disconnect, turn all controls to the off position, then remove plug from outlet.
- WARNING : Risk of Injury – Keep children away from this furnishing.
- WARNING : Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
- GROUNDING INSTRUCTIONS:
- For a permanently connected product: This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product.
- For a grounded, cord-connected product rated max 15 amperes and intended for use on a nominal 120-volt supply circuit :
- This product is for use on a nominal 120-volt circuit and has a grounding plug. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.
- For loading always put heavier items at the bottom and not near the top in order to help prevent the possibility of the furnishing tipping over.
- WARNING : Risk of Injury to Persons – do not use this furnishing to support video equipment such as televisions or computer monitors.
- Mount furnishings at the correct height.
- This unit is suitable for installation in a damp, indoor location only.
- This unit is to be mounted to a metal electrical junction box (outlet box) directly supported by the building structure.
- Save this instruction for future reference.
- Estimated Assembly Time: 20 minutes
Tools Required For Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape and Wire cutters. Helpful Tools (not included): Wire strippers, Ladder.
HARDWARE INCLUDED
Installation Instruction
Temporarily secure the paper (G) to the wall, then mark the anchor (D) locations on the wall through the holes. Remove the paper (G) and drill holes making them slightly smaller than the anchors (D) provided.
Option 1
Option 2
OPERATION INSTRUCTIONS
- Short touch: ON and OFF
- Short touch to turn ON and OFF for the defogger function.
- Short touch to adjust the colour temperature: 3000K (Warm), 4500K (Neutral), 6400K (Cool). Press and hold: Stepless CCT.
FAQ
How do I clean the Lenora lighting product?
To clean the product, first, make sure it is turned off and disconnected
from the power source. Gently wipe the surface with a soft, dry cloth. Avoid
using harsh chemicals or abrasive materials.
What should I do if the LED light source stops working?
If the LED light source malfunctions, contact Customer Service & Tech
Support at 905-695-2147 or email
Info@eurofase.com for assistance. Do not attempt to repair the LED components
yourself.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>