CILICO C7X Mobile Computer User Guide
- June 5, 2024
- Cilico
Table of Contents
C7X Mobile Computer
**User Guide
**
Accessories list:
- Mobile Computer
- Charger
- USB cable
- Quick start guide
- Qualification certificate
- 7200mAh battery
- Handstrap
CALICO Microelectronics Limited
contact@cilico.com
www.cilico.com
HQ Add: 4th Floor, Building A, HuixinlBC, Zhangba 1st Road, Hi-tech Zone, Van
China Shenzhen add: 2nd Floor, Building A, Runfeng Industrial Park, Baoan,
Shenzhen, China
Overview for Mobile Computer
Indicator Description
Open/Lock the Back Cover
Install the SIM/P-SAM Card
Install Battery
Insert/ Remove Micro SD Card
Barcode Scanning (optional function)
1D/2D barcode module can help you collect barcode information easily. Following is the operation steps.
Enter “Menu “Settings” furn ON Left Scan” or “Right Scan”
Enter “Messaging Select “New Message” the cursor moves to Type Text Message”
1dscanning beam (or 2d scanning area) will be emitted from the scanning window, adjust it at the center of the bar&ode.
You will hear a short sound after reading successfully, and the barcode will be displayed in the receiving text box
Above is the virtual keyboard message scanning mode, if you need to develop
via serial port mode, please contact relevant technical support.
NFC
The NFC reading area is marked on the back cover of the battery, the
reading distance is 0-5cm.
NFC function default on open.
when it is off, operating steps as below:
Enter “Menu”**→**“Settings
”**→**“Wireless & networks
”**→**“More…” Turn ON NFC
Steps for use**→**Open loT toolbox
**→**Click the NFC icon
**→**Close the NFC card to the battery cover
**→**NFC card content display
Warm Tips:
- Pls, ensure fully charge the battery(100%) for first-time use.
- Pls, charge in time if power is lower than 20%
Specific Absorption Rate (SAR) information:
This Mobile Computer meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluations
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health. FCC
RF Exposure Information and Statement
the SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue.
Device types: Mobile Computer has also been tested against this SAR limit.
This device was tested for typical body-worn operations with the back of the
Mobile Computer kept 0mm from the body. To maintain compliance with FCC RF
exposure requirements, use accessories that maintain an 0mm separation
distance between the user’s body and the back of the Mobile Computer. The use
of belt clips, holsters, and similar accessories should not contain metallic
components in its assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements and should be
avoided.
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modi cations to this device not explicitly
approved by the manufacturer could void your authority to operate this
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.