COREMORROW XYZ65N81E26 Linear Piezo Nanopositioning Stage User Manual
- June 9, 2024
- COREMORROW
Table of Contents
COREMORROW XYZ65N81E26 Linear Piezo Nano positioning Stage User Manual
DECLARATION
Thank you for choosing Core morrow’s products! This user manual is applicable
to XYZ65N81E26 linear piezo Nano positioning stage. For your smooth and
correct use of this product, please read this manual carefully before use.
Please follow the instructions in the manual installation and use procedures.
Improper operation may cause injury to the operator or damage to the product.
Therefore, the entire installation and operation process should be completed
by a professional with a certain foundation and understanding of the product
principle, or under the guidance of a professional. If the product is
disassembled or modified without permission, our company will not be
responsible for any consequences arising therefrom. It is illegal to change
the product model and other false sales of our products. Users are advised to
be vigilant. Once you find out or be deceived, contact us directly, we will
crack down on illegal activities and prevent deception and economic losses.
Core Morrow will certainly investigate legal responsibility of the illegal
subject and related parties. With the continuous development and innovation of
technology, we will add the latest information to the manual as needed without
notice. Please contact us if you need any information.
1. Introduction
1.1 Purpose and content
- The manual is mainly for your smooth and correct use of piezo products.
- The manual contains all necessary information for XYZ65N81E26.
- The manual describes the precautions during installation and use.
1.2 Symbol and meaning
⚠ DANGER: Improper handling may could cause injury to the operator.
ℹ Attention: Improper handling can cause damage to the equipment.
No order between items.
1. ▶
Please operating in order.
2.
1.3 Expected reader
The manual default user has knowledge of linear piezo Nano positioning stages and controllers, and has a basis for its installation and use.
1.4 Manual lost replacement
If the manual is accidentally lost, please contact our customer service department, we will send you the latest version of user manual.
2. Safety Guide
XYZ65N81E26 linear piezo Nano positioning stage is designed with advanced technology and safety standards, for safety and proper use of the product, please pay attention to following points when using:
⚠ Temperature changed and pressure will charge the piezo product. It will
remain charged for a period of time disconnected from the controller, so the
operator should pay attention when using it:
▶ Do not disassemble piezo stage;
▶ Discharge piezo stage before installation, it could be achieved by
connecting to the controller;
▶ Do not pull out the controller during operation;
▶ Before using, please check whether the connecting wire of the product is in
good condition, whether the product and the controller are effectively
protected from grounding, in case of danger, please strictly regulate the
operation during operation, do not touch it (up to 120V voltage) after power
on.
ℹ In order to prevent damage to the product caused by improper operation,
please pay attention to following points when using:
▶ XYZ65N81E26 linear piezo Nano positioning stage is used as much as possible
in dust-free, oil-free, lubricant-free environments;
▶ Since the product adopts flexible structure design, it is recommended that
the load not exceed the bearing capacity of the product. Pay attention to the
torque when loading. Do not twist or twist the load surface to avoid damage to
the structure;
▶ Do not disassemble the product to avoid product damage;
▶ Avoid stretching and bending the cable interface to prevent damage to the
cable;
▶ Please use the dedicated cable provided by us to connect XYZ65N81E26 linear
piezo Nano positioning stage and piezo controller;
▶ Please do not use cable extension wire, if need longer cable, please contact
us.
3. Product Overview
3.1 Product Introduction
XYZ65N81E26 linear piezo Nano positioning stage is piezoelectric screw motion platform, with a combination of linear motor piezoelectric screws and a sliding stage, and the high precision motion of the piezoelectric screw is used to control the movement of the sliding stage.
3.2 Product Features
▶ Travel up to 25.4mm/axis
▶ XYZ motion
▶ Displacement increment <30nm
▶ Standard and vacuum versions are available
3.3 Motion Direction
4. Operating Environment
▶ Operating temperature: 0~50
▶ Environment free of dust, clean, and non-corrosive substances
▶ Relative humidity: <60%
5. Installation and Operation
Before installation, first check the safety, such as whether the cable is damaged or broken, and whether the power supply has grounding protection.
5.1 Installation and announcement
5.2 Load
When installing the load, ensure that the load mass is less than the max load of piezo stage, and install the load as much as possible at the center of the moving surface. The correct placement of the load is shown below:
For protection, we don’t recommend the load is too high. If it is used a higher load, please reduce the position center of the load gravity. The error placement method is as follows:
It is forbidden to load the load on one side of the piezo stage, which would cause serious damage to the product, as shown in the following figure:
If the screws used in tightening and
connecting are too long, the screws will not be installed or some of screws
will leak out, which will scratch the piezo stage and affect the motion
accuracy. If the screws are too short, the connection will not be compact and
easy to loosen. Looseness could damage the internal structure of the piezo
stage. We recommend using the connection method shown below:
Note: Slowly tighten the load when installing it, and the torque should not be
too large to avoid damage to mechanism. Avoid stretching and bending cables.
Please connect linear piezo Nano positioning stage and controller with special
cable provided by Core Morrow.
Please do not extend the cable without authorization, please contact us if you
need a longer cable.
5.3 Operating
Please confirm the following information before starting the power supply: The
environment meets requirements of piezo products operating environment. The
fixing screws must be tightened.
The above information is determined to perform controller related operations:
- Please carefully read piezo controller user manual before operating, then start the controller;
- Set the piezo controller to zero;
- It could work normally within the rated voltage range of piezo stage.
- Please set the piezo controller to zero after used.
- If abnormal noise or oscillation occurs during use, immediately turn off the power and check parameter settings.
6. Transportation and Inspection
6.1 Transportation
Product is packed in carton. The transportation is carried out under the condition of packaging. This product can be transported by various means of transportation under normal conditions. During transportation, it should avoid direct rain and snow, avoid contact with corrosive substances, and avoid strong collision, try to avoid improper Behavior such as squeezing, irregular placement.
6.2 Unpacking inspection
Please check below information: Before opening the package, please carefully
check the packaging for damage, bruising, wetting, moisture, deformation, etc.
Please check the parts on a case-by-case basis based on the supply contract
and the packing list. Whether there is obvious damage on the surface of the
product. Whether the product identification is clear and complete. Whether the
connector is loose, the connection line is broken or not, etc.
If any of the above occurs, please make a detailed record and take a photo,
and please contact us immediately. Precautions:
Please handle gently when unpacking to avoid permanent damage to the products
caused by bumps.
Please do not use heavy tools or use rough methods to open them. Please do not
discard all packaging materials for return shipments.
7. Maintenance and processing
7.1 Problem Processing
If the user has problems that could not be solved. Please record the fault
situation and contact with us. The professional technical engineer would help
solve the problem.
Problems caused by improper operation are not covered by the warranty; Core
Morrow is not responsible for any problems caused by dismantling the piezo
stage without permission.
7.2 Daily maintenance
If the product is not used for a long time, please store it in an room
environment with no dust, good ventilation, clean and non-corrosive
substances.
Please do not loosen the screws on the stage structure, avoiding to affect the
accuracy. Daily cleaning:
Please disconnect the piezo stage to controller, then clean the surface of it.
When cleaning, first wipe a small amount of detergent with a towel and gently
wipe the surface of the piezo stage, then wash it with alcohol. Please do not
use ultrasonic waves for cleaning.
8.Customer Service
If you have questions about the products you are currently using, please let
us know the following information:
Product model number and related number. Controller model for this product.
Software driver version for this product. Computer operating system for
installing supporting software.
9.Contact us
Harbin Core Tomorrow Science & Technology Co., Ltd.
Tel: +86-451-86268790
Email: info@coremorrow.com
Website: www.coremorrow.com
Address: Building I2, No.191 Xuefu Road, Nangang District, Harbin, HLJ, China
CoreMorrow Official and CTO WeChat are
below:http://weixin.qq.com/r/PEzawqnEyfS2re2h9xkuhttps://u.wechat.com/EAOWfcTPsTfQdVIeK41V9hg
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>