HelloBaby P24TX 2.4GHz Digital Wireless Video Baby Camera User Manual

User Manual
2.4GHz Digital Wireless Video Baby Monitor
2.4GHz Digital Wireless Video Baby Camera
Ver:1.2

Model: HB2438
Tho pictures are for reference only, please subjectto pracicaiiy.

Thank you for purchasing the H82438 Baby Monitor. With our baby monitor, you could see and hear your baby sleeping or playing in their room anytime.
Please retain your original dated sales receipt for your records. For warranty service of your product, you will need to provide a copy of your dated sales receipt to confirm warranty status. Registration is not required for warranty coverage.

PLEASE MAKE SURE THE FOLLOWING INCLUDED IN YOUR PACKAGE

SAFETY INSTRUCTIOINS

Caution: Keep the device away from children, Strangulation hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (0.9m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.
Choking hazard : This product contains small parts, please be careful when unpack and assemble the product Read and keep to instructions:
All the safety and operating in structions should be read before the video baby monitor is operated. This product cannot replace responsible adult supervision.
Water and moisture: The unit should not be exposed to rain, moisture, dripping or splashing.
No objects filled with liquid should be placed on top of, or beside the product, such as a glass.
or vase. This item should not be used near water.
Do not: Use the appliance if the cord or plug is damaged. If your baby monitar is not operating properly or has suffered any damage, contact “service@hellobaby.net.cn” service center to request inspection and repair of the appliance in order to avoid any possible risk.
Do not: Attempt to repair or adjust any of the electrical or mechanical functions of the unit.
Otherwise, the guarantee will be made void
Ventilation: his baby monitor should not be used on a bed, sofa, rug or similar surface that may block the ventilation openings, or be placed in an enclosed area such as a bookcase or drawer that may impede air flow.
Keep away from sources of heat: This unit should not be exposed to direct heat sources suchas a candle, radiator, heat register, stove or other appliance that emits heat. The unit should not beleft in direct sunlight.
Power source: This unit should only be used with the AC power adapters included in this package (rated 5V DC 14)

Damage requiring service: This unit should be serviced by qualified personnel anly when:

1. Objects have fallen or liguid has been spilled into the product.
2. The units have been exposed to rain
3. The units do not appear to operate normally or exhibits a distinct change in performance.
4. The units have been dropped or the enclosure damaged.

WARRANTY TERMS.

We offer one-year warranty from the original purchase date against defects  in workmanship.and materials. Ifyou have warranty or support ssues, please contact our after-sales service via email.

INSTALLATION GUIDELINES

• To use your parent unit and camera unit together, you have to establish a radiolink between them, and the range wil be affected by environmental conditions.
• Any large metal object, like a refrigerator, a mirror, a illing cabinet, metallic doors or reinforced concrete between the baby and parent unit may block the radio signal.
• The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TV, computers, cordless or mobile phones, fluorescent lights or dimmer switches.
• Use of other 2.4GHz product, such as wireless netwarks (Wi-Fi routers), Bluetooth systems, or microwave ovens, may cause interference with this product, so keep the baby monitor away at least 5ft (1.5m) from such products, o turn them off if they cause.
  interferences.

PLACEMENT OF THE BABY MONITOR

The camera can be placed on the desktop or mounted on the wall. Don’t place baby monitor on soft quilts or blankets or in the corners of cupboards, shelves, etc; Keep the baby monitor away from heat sources such as radiators, chimneys, cookers and direct sunlight; Keep the baby unit away from TV sets, microwave oven and radios. Ifinterference occurs, move the camerato elsewhere,

• Place the camera within 6 feet (2 meters) of the area being monitored for optimum performance.

GETTING STARTED

5.1 TURN ON THE BABY UNIT:

1. Insert the DC plug of the power adapter into the DC jack in the rear of the Baby Unit.
2.  Insert the other end of the power adapter into a suitable electrical outlet.
3.  0nce the adapter is connected, the power LED willlight up.
4. keep the baby unit plugging in.

5.2 TURN ON THE PARENT UNIT:

1. Insert the DC plug of the power adapter into the DC jack in the side of the parent Unit
2. Insert the other end of the power adapter into a suitable electrical outlet.
3.  Press and hold the power key 3 seconds on the side of the parent unit.
4. 0nce parent unit is on, the power LED willlight up and the image will isplay on the LCD.
   Note: When the product isin use, the antenna needs to be pulled up, so that the signal Is the best

5.3INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function allows the camera to pick up images n dark or low Hght conditions. I this made, anly black and white images will b displayed on the monitor the aptimum mage e in where baby uni i 6t (2m) way ffom abject. The camera s n ight vision mode,the con willbe displayed o the top o creen.

PRODUCT OVERVIEW

6.1BABY UNIT OVERVIEW:

6.2 PARENT UNIT OVERVIEW:

6.31CONS OVERVIEW

KeY OPERATION

7.1POWER SAVE) SCREEN OFF
Shortpress the power key toturn on/ ffth sreen.
7.3 VOLUME ADIUSTMENT
Press the key o ncraase the volume; Pres the keyto decrease the volume
7.3 BRIGHTNESS ADIUSTMENT
Pres the Key o ecrease the bightness; Pres the Key o increase the brightness

7.4 CAMERAVIEW / SCAN
Press Scan key toview scan camera; During scan mode, the scanicon be isplayed on the top of screen. And each camera’s video willstay o the LCD around 10 seconds andthen turnto next camera lternately
7.5 DIGITALZOOM & PAN / TILT.

Press and hold the key around 2 seconds o operate Zoom in| out At the Zoom mode, press the key 1 Pan ft ross ey to anrih.arss A Koy up press oy o 1 GownDuring digts z0om mods, the zp0m Icon will e dislayed on th top of sereen Warm reminder: I you want to sdjust the volume/Brighiness, you haveto exit the Zoom mode before you operate .

MENU OPERATION

8.1 PAIRING THE CAMERA AND PARENT UNITS.

The baby unit is pre-registered to your parent unit. You do not need to register it again
unless the baby unit loses connection with the parent unit. To re-register your baby unit,
or register anew baby unit, follow the steps below:
Note: Cameraiconwith” “means itis well registered. You should select and pair with
the cameraicon without” “sign.
8.1.1 ADD CAMERA

1. Press the MENUG key then the menu will pop up.
2. Press the key until the camera icon is selected.
3. Press OK key to enter into sub-menu, then press key to select your desired camera.
4. Press key enter into sub-menu; Press key to select then press key.
5. When the icon x … displayed on the LCD screen, press the PAIR button on the back of camera.
6. Once paired, Successful pairing icon © shows on the LCD screen.
   7. If fails, repeat the above steps.

8.1.2 DELETTING A CAMERA

1. Press the MENU key and the menu will pop up;
2. Pressthe key until the camera icon A is selected.
3. Press oK   key enter into sub-menu; then press Wkey to select your desired camera
4. Press oxK key enter into sub-menu; Press key to select then press OK key;
5. Press key to select .
6. Press OK key to confirm.
7. Press the key to exit.

8.2 ALARM SETTING

You can use the alarm to remind yourself to feed your baby / change diaper / sleeping, etc.

1. Press the button and the menu bar will pop up.
2. Press the key until the alarm icon is selected.
3. Press oK key enter into sub-menu, Press the ¢/ ®/A/¥V key to selected the alarm time you need.
4. Press OK key to confirm.

Note 1: The minimum unit is 0.5 hour. The maximum setting is 5 hours (7 levels).
Note 2: Once the alarm is turned on, alarmicon will display on top of the screen.
Note 3: The alarm default setting is OFF.
Note 4: When the alarm is ringing, press any key on the parent unit to turn the alarm off.
Note 5: If you don’t turn off the alarm, the alarm will ring for 1 minute. After three minutes the alarm will ring again for 1 minute. The alarm will ring for three times in total, after this the alarm goes off.
8.3 ENERGY SAVING
This mode allows you to control the sound activation of your baby unit. If there is no sound around the baby unit within 30 seconds, it will stop audio transmission and turn off the screen of the parent unit. When the baby unit detects any sounds louder than the sensitivity level, it will start transmitting the signal to the parent unit again and turn on the screen of the parent unit. To change the ECO level, please follow the below instructions.

1. Press the MENU key then the menu will pop up.
2. Press the key until the ECO icon is selected.
3. Press ox key enter into sub-menu, then press A/¥ key to select desired level.
4. Press OK key to confirm.
5. Pressthe key to exit.

Note Low sensitivity level, the baby have to make a lot of sound before the ECO
function is activated.
Note :- is middle sensitivity level.
Note : – is High sensitivity level, the baby don’t have to make a lot of sound before the

8.4 LANGUAGE SETTING

1. Press the MENU key and the menu will pop up.
2. Pressthe keys until the language icon is selected.
3. Press key to enter into sub-menu, then press key to select the language you need.
4. Press key to confirm.
5. Press key to exit.

TECHNICAL DATA

Output: 5V DC 1A
Camera Unit: Input: 100-240VAC 50/60Hz
Output: 5V DC 1A
Operating Range| Up to 1000ft outdoor line of sight Up to 165ft indoor
Display| 3.2″ IPS TFT LCD
Rechargeable Battery for Monitor| 3.7V,950mAh,3.515Wh
Battery Life| Up to 6 hours
Camera Unit and Parent Unit RF Power ( for CE)| less than 20dBm
Operation Rnvironment| Operation Temperature: +32F-+104F (0°C-40°C) Battery Charging Temperature: +50E-+104F (10°C-40°C)
Relative Humidity : 15%-85%

TROUBLE SHOOTING

No Reception on The Monitor| * The power adapters may not be properly connected.

• Confirm that the camera and monitor are ON.
• Camera may be far away from the monitor.
• Camera and monitor may not be properly paired; follow PAIRING instructions.
  ---|---
  Interference or Poor Reception| * Move the monitor close to the camera.
• The camera or monitor may be placed too close to many metal objects. * Other electronic devices may be interfering with the signal.
• The battery power may be too low.
  Audio Feedback (High Pitched Noise)| The camera and monitor may be placed too closed. The volume on the monitor may be set too high.
  Frozen Picture on Screen| * Repower the baby unit (plug out the adapter, then plug it into the socket again).
• Press the RESET key at the back of parent unit.

MAINTENANCE

• Clean your baby monitor with a slightly damp or anti-static cloth.
• Never use cleaning agents or solvents

DISPOSAL GUIDE FOR BATTERY AND PRODUCT

• Do not attempt to repair or adjust any of the electrical o mechanical functions of the unit.
• Remember to dispose of the product in an environmentally responsible way.
• For proper collection and processing of these products, take them to the collection points designated by local authorities. You can also contact the store where you purchased the product Improper orincorrect use of batteries may cause corrosion or battery leakage, which could cause personal injury or damage to property. Use only the types of the batteries which are indicated in this manual

CAUTION : Risk of Fire and Burns. Do Not Open, Crush, Heat Above 45 degree Cor Incinerate.
Follow Manufacturer’s Instructions.

Disposal of abattery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can resultin an explosion.

• Leaving a battery in an extremely high temperature surrounding environment that can resultin an explosion or the leakage of flammable iquid or gas.
  Abattery subjected to extremely low air pressure that may resultin an explosion or the leakage of flammable liquid or gas.

• The battery shall not be exposed to excessive heat such as sunshine, fire or the like.

FCC& ISDE Statement

This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s}.Operation is subject ta the following two conditions: (1)this device may not cause harmful interference, and (2}this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class 6 digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occurina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.

Radiation Exposure Statement for camera

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
SAR Statement for Monitor

Specific Absorption Rate (SAR) information:
This Monitor meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all persons regardless of age or health. ISED & FCC RF Exposure Information and Statement the SAR limit of Canada{ISED & FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: Monitor has also been tested against this SAR limit. This device was tested for typical body-worn operations with the back of the Monitor kept Omm from the body. To maintain compliance with ISED RF exposure requirements, use accessories that maintain an Omm separation distance between the user’s body and the back of the Monitor . The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with ISED RF exposure requirements, and should be avoided.
EU Declaration of Conformity (DOC)
Hereby, videotimes declares that the radio equipment type is in compliance with RED Directive 2014/53/EU.
The full text of the EV declaration of conformity is available on the website: www.hellobaby.net.cn
Model: H62438
Responsible Party(US): Startline LLC
Add: 22 Hazelwood Drive, Jericho, NY 11753 Tel: 1-516-681-3729
Authorized UK Representative(UK): APEX CE SPECIALISTS LIMITED
Add: 89 Princess Street, M14HT,UK info@apex-ce.com
Shenzhen Videotimes Technology Co.,Ltd
Room 2106, Building 11, Tianan Yungu Phase II, Gangtou Community, Bantian Street,
Longgang District, Shenzhen, Guangdong, China

WARNING

Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9 m) away). Do not remove this tag.

Risk Group 1

WARNING IR emitted from this product. Do not stare at operating lamp

Product tested against EN62471

Madein China

www.hellobaby.net.cn
service@hellobaby.net.cn

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>