VEVOR HS-1000A 12V Air Compressor with Tank Instruction Manual
- June 1, 2024
- VEVOR
Table of Contents
VEVOR HS-1000A 12V Air Compressor with Tank
We continue to be committed to providing you tools with at competitive prices. “Save Half”, “Half Price” or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and do not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are saving half in comparison with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us:
Technical Support and E-Warranty Certificate
www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
PARAMETER LIST
PART LIST
SECURITY & WARNING
Read this instruction before using this product. Failure can result in
serious injury. Always observe the rules of safe operation.
- The temperature of the compressor may be very high during operation or after it has stopped, so do not touch it with bare skin.
- Install the system in a level, cool, dry place. Avoid hot andhumidareasan
- assembly.
- Keep the assembly area clean and well-lit.
- Keep bystanders out of the area during assembly.
- Do not assemble when tired or when under the influence of alcohol, drugs or medication.
- Product capabilities apply to properly and completely assembled products only.
- Assemble on a flat, level, hard and smooth surface capable of safely supporting a fully loaded truck air horn.
OPERATION
Step 1
Use a 14 mm open wrench or a 14 mm socket wrench to fix the compressor to
the car with (4 M8 bolts, 4 nuts, 4 flat washers, 4 rubber cushions). Install
the bolts through the gasket – compressor support – rubber washers – car.
Step 2
Use a 10 mm open wrench or a 10 mm socket wrench to fix the horn support to
the horn and the car using four M6 bolts, four M6 nuts, and one tripod.
Install the bolts through the tripod – one end through the horn lock nut, and
the other end through the car frame lock nut.
Step 3
Attach the connector nut to both ends of the hose as shown below.
Step 4
Insert the hose into the connector as shown below (the hose will be easier to
install after heating)
Step 5
Install and tighten the air pipe nut using a 12.
Step 6
Screw the sealing belt around the compressor gas pipe joint, and roll the
sealing belt to the thread for more than 5 laps (if not sealed, the number of
laps can be increased until sealed)
Step 7
The compressor gas pipe is installed on the reservoir (tighten with 17MM open
plate)
Step 8
Use a Phillips screwdriver and an 8MM open or socket wrench to fix the
compressor to the frame using M5 bolts 4 flat gaskets 8 spring gaskets 4 M5
nuts 4 Installation sequence: Screw through the spring gasket-flat gasket-
compressor bracket – car frame – flat gasket-nut.
Step 9
Connect the horn line. The horn has two power lines (regardless of positive
and negative): one iron (negative grounding), and the other is connected to
the positive power supply after the horn switch. (16AWG and above copper wire
are required as connection wires.)
Step 10: Compressor line connection
Compressor main line connection (here, need to use copper wire12AWG, 12V 30A
relay, 30A power switch, 30A safety) compress or blackwire (negative), red
line through the safety to the relay to port 87, relayport30 to the power
switch, the power switch to the battery positive terminal.10.2 Pressure switch
circuit connection (Copper wire 16AWGisrequiredhere) The pressure switch
wiring terminal is connected to two wires (positive and negative), one is
connected to the relay port 85, and Bayport 86 is connected to the output end
of the compressor power switch.
Troubleshooting
CORRECT DISPOSAL
This product is subject to the provision of EuropeanDirective2012/19/EU. The
symbol showing a wheelie bin crossed through indicates that the product
requires separate refuse collection in the European Union. This applies to the
product and all accessories marked with this symbol. Products marked as such
may not be discarded with normal domestic waste but must be taken to a
collection point for recycling electrical and electronic devices.
Technical Support and E-Warranty Certificate
www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>