XK Innovations WL917 RC Racing Boat Instruction Manual

WL917 RC Racing Boat
Instruction Manual WL917
RC/Racing Boat

WL917 RC Racing Boat

Please read the instructions carefully, before operation, indicating that the picture might be different in kind, Please prevail in kind.

1. This product realizes forward navigation by spraying water column at a high speed backward. It has no leakage blades and high safety. It uses advanced 2.4G two-way transmission technology to return the alarm signal when the power is insufficient.
2. 7.4V 800MAH 15C high discharge rate high capacity lithium battery. Life of about 12 minutes.
3. Specification of the hull length (260MM)
   Hull width (96MM)
   Hull height (83MM )

(Remote Control Battery Installation)

Battery: open the battery cover and place two 1.5V AA batteries on the remote control.
The positive and negative poles of the battery should be placed correctly, and then close the battery cover. (see Figure)

(Rechargeable battery)

Connect the battery and charger, the charger into a power outlet for charging about 120 minutes.

(Ship models battery installation method)

1. Loosen the locking knob of the ship cover and open the ship cover.
2. Put the battery into the battery box, fix it, then cover it: the cabin cover, and tighten the knob.

ThWhen the boat touched the electric cooling system pipes attention should not be folded, so as not to cause unreasonable waterway brushless motor, brushless ESC temperature is too high and burn.

(Code matching between ship model and remote controller)

First power on the ship model, and then switch on the controller. Turn the direction knob, turn the injection port left and right, and the code alignment is completed.

(Security Alert)

1. batteries should be replaced by adult.
2. You can not charge the battery immediately after use, must wait until the battery to cool before charging.
3. Use only with box and instructions on the recommended batteries.
4. Carefully follow the instructions in the correct battery polarity into the battery.
5. Do not mix old and new batteries and rechargeable batteries, or different types of batteries.
6. non-rechargeable battery is not charged.
7. Charge the rechargeable battery before the first battery is removed from the Ship model.
8. can only be under the guidance of adult rechargeable battery.
9. dead batteries should be removed from the yacht.
10. Avoid short circuit. Short circuit may cause the battery and charger to overheat or cause other damage. Ensure Battery pack and charger during charging out of reach of small children. Not near the fire or by Near relatively high  temperature or humid places charge. Charger when charging a slight fever.
11. Do not touch the propeller body.

(Method of operation}

1. When using the remote control and the ship model of good code. Mold boat into the water, will pull back the throttle, propeller, ship model forward to the direction of rotation of the knob left / right, ship model left / right (when the  remote control is running low, the power light starts flashing, with an alarm sound, then the need to replace the battery) .

2. before use to determine without interference around
   Note! (1) users under 14 years old must be supervised by an adult action.
   (2) observe the water before sailing into the water without debris, if too much debris, sailing boats may Entangled in the propeller will be suspended, the water is not recommended in these operating boats.

3. When not using the boat, remove the remote control and the boat battery.

4. the radius of 80 meters remote control speedboat product, please be careful not to exceed the remote range to avoid runaway.

(Fine tuning operation method)

Adjust the middle knob on the remote control to adjust the straight-line driving performance of the ship model.
When the ship moves to the right, adjust the knob to the left until the ship model moves in a straight line.
When the ship moves to the left, adjust the knob to the right until the ship model moves in a straight line.

(Low voltage return warning)

1. During operation, if the remote control sends out a drip warning sound and the ship cutting speed is significantly reduced, the battery on the ship model is insufficient. Please drive the ship back to the shore as soon as possible.
   Attention! After the power warning prompt is started, the remote control will make a drip sound all the time. In order to avoid running out of power, please drive the ship back within one minute.

(Maintenance of ship model)

1. After each play, clean the water in the cabin in time and wipe the water off the hull with a soft cloth Don’t cover the bunker cover until the water in the bunker evaporates naturally.
2. Seawater is more corrosive than fresh water. After playing with seawater, the water on the ship model must be cleaned in time to avoid damaging the mechanical transmission parts.
3. If you don’t play for a long time, take out the battery on the remote control.

(Main accessories)

Warning:
This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of f and on, the user is encouraged to try to  correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver .
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>