soundsation WF-U199 UHF 99 Channel Stereo In Ear Monitor System User Manual

WF-U199 INEAR
UHF 99-Channel Stereo
In-Ear Monitor System USER MANUAL

Please read this manual carefully and proper take care of this manual.

WF-U199 UHF 99 Channel Stereo In Ear Monitor System

Dear customer,
First of all thanks far purchasing a SOUNDSATION® product. Our mission is to satisfy all possible needs of musical instrument, professional audio and lighting users offering a wide range of products using the latest technologies.
We hope you will be satisfied with this item and, if you want to collaborate, we are looking for a feedback from you about the operation of the product and possible improvements to introduce in the next future. Go to our website www.soundsationmusic.com and
send an e-mail with your opinion, this will help us to build instruments ever closer to customer’s real requirements.
One last thing: read this manual before using the instrument, an incorrect operation can cause damages to you and to the unit. Take care!
The SOUNDSATION Team

IMPORTANT SAFETY SYMBOLS

| The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
---|---
| The symbol is used in the service documentation to indicate that specific component shall be replaced only by the component specified in that documentation for safety reasons.
| Protective grounding terminal
| Alternating current/voltage
| Hazardous live terminal
ON| Denotes the apparatus is turned on
OFF| Denotes the apparatus is turned off
WARNING:| Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION:| Describes precautions that should be observed to prevent danger of the apparatus.

TAKING CARE OF YOUR PRODUCT

• Read these instructions
• Keep these instructions
• Heed all warning
• Follow all instructions

Water / Moisture
The apparatus should be protected from moisture and rain and can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.
Heat
The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.
Ventilation
Do not block areas of ventilation opening. Failure to do so could result in fire. Always install according to the manufacturer’s instructions.
Object and Liquid Entry
Objects must not fall into and liquids must not be spilled into the inside of the apparatus for safety.
Power Supply
In case of external power supply, the apparatus should be connected to the power supply only of the type as marked on the apparatus or described in the manual. Failure to do so could result in damage to the product and possibly the user.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Electrical Connection
Improper electrical wiring may invalidate the product warranty.
Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzene or alcohol.
Servicing
Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. Only use accessories/attachments or parts recommended by the manufacturer.
Warning
Please remember the high sound pressure do not only temporarily damage your sense of hearing, but can also cause permanent damage. Be careful to select a suitable volume.
Interference from cell phone
Using a cell phone near the wireless system can induce noise. If this occurs, move the cell phone further away from the components of the wireless system.

UNPACKING

SOUNDSATION WF-U199 INEAR monitor wireless system is composed by the following parts:
2.1. WF-U199 INEAR

• Transmitter
• Pocket Receiver
• Antenna
• Earphones
• External Power Supply
• 2x Type-AA 1.5V Batteries
• Rack Adapter Kit (2 brackets)
• Antenna Extension Cable
• This Manual

2.2. WF-U199 RX

• Pocket Receiver
• Earphones
• 2x Type-AA 1.5V Batteries
• This Manual

ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!!
Keep in a safe place the original packaging material for future use.

ACCESSORIES

SOUNDSATION can supply a wide range of quality accessories that you can use with your WIREFREE Series in-ear monitor system, like Cables, Mixers, Speakers, Amplifiers, Stands, etc.
All products in our catalogue has been long tested with this device so we recommend to use Genuine SOUNDSATION Accessories and Spare Parts.
Ask your SOUNDSATION dealer for any accessories you could need to ensure best performance of the product.

OVERVIEW

WF-U199 INEAR monitoring system is for all those professionals who need maximum mobility on stage without losing a reliable stereo monitoring system and high quality audio.
Rugged, reliable, easy to transport and install, the WF-U199 INEAR features independent Stereo/Mono modulation functions, PLL technology and 99 channels. The pocket receiver is equipped with illuminated LCD and is absolutely easy to set up. It is supplied
with earphones that provide an optimal reproduction of the entire audio spectrum.
In the package you can also found various ear-fitting pads for an individual fit.
The half-rack receiver unit is provided with a 19” standard rack mount kit. All connections are balanced and assure maximum audio standards.
Lastly, an optional kit – the WF-U199 RX – is available to add additional receivers (and earphones) in case there were more musicians or users who need to hear the same audio content. Ask your dealer or visit the website SOUNDSATION www.soundsationmusic.com for further details.

MAIN FEATURES

• UHF Phase Lock circuit, stable and with low harmonic radiation
• 99-Channels in 10 Groups with frequencies arranged in order to avoid interferences
• 606 – 613.5 MHz Carrier Wave Frequency Range
• User-friendly interface with a wide illuminated LCD Display
• Independent Mono/Stereo Modulation Function between Transmitter and Receiver
• Excellent circuit design to achieve the best signal/noise ratio
• Supplied with High-Dynamics Earphones in soft Case
• Compact and robust Receiver Configuration Design
• 19” Standard Rack Mount Transmitter with Mounting Kit
• Balanced/Unbalanced Inputs with Combo Connectors

APPEARANCE

6.1. Sizes:

TRANSMITTER FEATURES:

7.1. Front Panel:

1. Power switch: ON/OFF button for transmitter (with on/off memory function)
2. LCD Screen: Displays information (for Group; Channel; Frequencies; and L/R Input AF etc.)
3. Function operation buttons: UP button, SET, DOWN button
4. L/R Input Level: Controls the monitor volume level
5. Headphones: 6.35mm Stereo Jack for headphones
6. Volume: Headphones output volume control

7.2. Rear Panel:

1. DC Input: DC input adapter jack: 12-18V – 500mA
2. LEFT Input: It’s the Line-level left input socket. It accepts both XLR and 6.3mm Jack (balanced and unbalanced).
3. RIGHT Input: It’s the Line-level right input socket. It accepts both XLR and 6.3mm Jack (balanced and unbalanced).
4. PAD switch: Use to adjust output gain. To cut gain, set to (-12dB). To leave gain unaffected leave set the switch to (0dB).
5. Antenna: BNC antenna connector.

BODY-PACK RECEIVER FEATURES:

1. Earphone Jack: 3.5mm Stereo mini jack for earphones
2.   Audio Output Control: Adjusts audio output volume
3. Antenna: Receives audio signal. Do not damage
4. Low Battery Indicator : This LED flashes red when battery is low
5. RF Signal LED: Lights up green when RF signal is received
6. LCD Screen: Displays information (For Group, Channel, Frequencies, and RF  battery etc.)
7.   ON/OFF Button: Single short press to switch the receiver On. Press and hold to switch the receiver Off
8. UP Button: Increases current parameter value during editing
9. SET Button: Press to choose parameters to change (Group, Channel, Stereo/ Mono). Press to confirm the selected value
10. DOWN Button: Decreases current parameter value during editing
11. Battery Compartment: Insert batteries here. The body-pack takes 2x 1.5V AA- Type batteries

8.1. Wearing the Body-pack Receiver Belt Clip : For best results, clip the receiver onto a belt by pushing the receiver down onto the belt as far as possible. For guitarists, Slide the guitar strap “through” the receiver clip.
8.2. Changing Batteries
Expected life for two Alkaline batteries is approximately 5-7 hours. When the LCD battery indicator is flashing, the batteries should be replaced. Following the instructions for their replacement:

• Apply a slight pressure at the top of the battery compartment door (11) and pull down.
• Insert or replace the batteries in the compartment, observing the +/- polarity marked on the bottom.
• Close the cover to prevent batteries to be lost during use.

SYSTEM SETUP

9.1. Transmitter Programming

Press the “Power” button (1 on section “7.1. Front Panel:” at page 8) to turn ON the system, press and hold for 3 seconds to turn it OFF (Diagram 1).
Frequency group and Channel selection:
Press the “SET” button (3 on section “7.1. Front Panel:” at page 8), the “Group” icon will flash.
Press “UP” or “DOWN” to select suitable frequency group number, as shown in Diagram 2 on the left.
Press the “SET” again to confirm. Now the “CHANNEL” icon will flash.
Press “UP” or “DOWN” to select suitable channel, as shown in Diagram 3 on the left, then press “SET” to confirm.
NOTE: When using multiple systems simultaneously, please choose distant groups in order to avoid interference.
Working Mode Selection:
Press the “SET” button (3 on section “7.1. Front Panel:” at page 8) until “STEREO” flashes.
Press the “UP” or “DOWN” button to choose between STEREO and MONO, then press “SET” again to confirm (Diagram 4).
NOTE: If no button is pressed during any setup operation for at least 5 seconds, the system automatically exits the setup mode and icons stop flashing.

9.2. Body-pack Receiver Programming
Power ON/OFF:
Turn ON the system by pressing the “ON/OFF” Button (7 on section “8. BODY- PACK RECEIVER FEATURES:” at page 9).
LCD screen will display the current group, channel, frequency, type of signal (stereo/mono), signal strenght and battery status.
NOTE: The display lighting is programmed to go off after about 10 seconds of inactivity, in order to reduce battery consumption.
Frequencies Group and Channel Selection:
Press the “SET” button, (9 on section “8. BODY-PACK RECEIVER FEATURES:” at page 9), the “Group” icon will flash.
Press “UP or DOWN” to select a group, then press “SET” again to confirm.
Now the “CHANNEL” icon will flash.
Press “UP” or “DOWN” to select suitable channel.
Press “SET” again to confirm.
MONO or STEREO Mode Selection: Press “SET” until the “STEREO” / ”MONO” icons are flashing.
Press “UP” or “DOWN” to choose between “STEREO” or “MONO”.
Press “SET” again to confirm the change.
NOTE: The display lighting is programmed to go off after about 10 seconds of inactivity, in order to reduce battery consumption.
RF signal Indication: The receiver altogether has five levels of RF signal indication.
This function is useful to choose the interference-free frequen- cies and install the better the system, so as to ensure the best operation.

AUDIO CONNECTIONS

You need XLR balanced cables for connections to your audio equipment. See the pictures below that show the internal wiring of these cables. Be sure to use only high quality cables (visit our website www.soundsationmusic.com for further details).
Balanced use of XLR connectors In case of unbalanced use Pins 1 and 3 will be jumped
Balanced use of 1/4” jack TRS connector You can, of course, connect even unbalanced equipment to balanced outputs. Use either mono and stereo jack, making sure ring and collar are connected together (or pins 1 & 3 in the case of XLR connectors).
Unbalanced use of 1/4” jack TS connector

RACK MOUNTING TRANSMITTER

The transmitter unit of the WF-U199 INEAR system can be mounted in a 19” standard rack unit using the accessories supplied with the product. The kit consists of:![soundsation WF-U199 UHF 99 Channel Stereo In Ear Monitor System

• RACK MOUNTING TRANSMITTER](https://manuals.plus/wp-content/uploads/2024/05 /soundsation-WF-U199-UHF-99-Channel-Stereo-In-Ear-Monitor-System-RACK- MOUNTING-TRANSMITTER.png)A. 1x 238mm metal plate
  B. 1x 35mm metal plate
  C. 1x Antenna extension cable
  NOTE: The kit doesn’t include screws to fasten the whole block (receiver and adapters) to the 19” rack chassis.
  11.1. Installing the rack-mounting kit

  1. Remove the two screws on both sides of the transmitter.
  2. Place the A plate so that the two lateral holes correspond to those on the side of the transmitter.
  3. Attach the two screws as shown.
  4. Repeat steps 1 to 3 on the other side of the transmitter by B plate instead of A one.
  5. Screw the antenna extension cable to the connector on the rear panel of the transmitter. Attach the other end of the cable to the panel so that you can then screw the antenna externally to the rack.

SPECIFICATIONS

SYSTEM

Carrier Frequency:| UHF 606 – 613.5 MHz
Number of Channels:| 99 in 10 groups
Frequency Stability:| ±0.005%, PLL phase-locked loop frequency control
Modulation:| FM Stereo
Effective Working Distance:| 80 meters (without obstacles)
Oscillation Mode:| PLL phase-locked frequency synthesizer
Maximum Deviation:| ±68KHz
Comprehensive S/N ratio:| >105dB
Comprehensive T.H.D:| <0.4% @1 kHz
Frequency Response:| 40Hz-16Hz ± 3dB
Stereo Separation:| ≥45dB @1 kHz
Packing Size (WxHxD):| 435 x 320 x 100 mm (17,12 x 12,60 x 3,94” in)
Packing Weight:| 2.5 kg (5,51 lbs.)
Monitor Stereo Transmitter
Chassis Specifications:| EIA 19” standard half-Unit
Output Power:| 30mW
Audio Input:| 2x Line Inputs with Combo Connectors (XLR and jack 6.3mm)
Audio Output:| 6.3mm Stereo Jack (headphones)
Transmitter Size (WxHxD):| 214 x 46 x 217 mm (8,42 x 1,81 x 8,54” in)
Transmitter Height with Antenna:| 250 mm (9,84” in)
Weight:| 1.06 kg (2,33 lbs.)
Mini Monitor Stereo Receiver
Audio Output Socket:| 3.5mm stereo headphone jack
Audio Output Power:| 2x150mW (THD3%)
Battery:| 2x AA-Type Batteries
Current consumption:| 185mA (typical)
Battery Current/life:| About 5-7 hours
Receiver Size (WxHxD):| 66 x 108 x 22 mm (2,60 x 4,25 x 0,86” in)
Receiver Height with Antenna:| 190 mm (7,48” in)
Receiver Weight:| 143 g (0,31 lbs.) (batteries included)

The product, specifications, and data are subject to change without notice to improve reliability, function or design or otherwise.

FREQUENCY TABLE

Ch.| Gruppo| Gruppo| Gruppo| Gruppo| Gruppo| Gruppo| Gruppo| Gruppo| Gruppo| Gruppo
---|---|---|---|---|---|---|---|---|---|---
| 1| 2| 3| 4| 5| 6| 7| 8| 9| 10
CH1| 606.175| 606.000| 606.275| 606.825| 607.700| 606.625| 606.500| 608.000| 609.975| 606.500
CH2| 608.050| 607.000| 607.875| 607.250| 608.975| 607.675| 607.350| 608.925| 607.600| 608.875
CH3| 609.525| 607.350| 607.800| 607.975| 609.500| 608.525| 608.000| 610.0.75| 609.675| 607.375
CH4| 611.775| 608.400| 608.200| 608.350| 609.500| 610.175| 611.000| 611.475| 612.725| 608.000
CH5| 612.600| 610.875| 610.925| 608.900| 610.750| 610.625| 611.400| 613.125| 606.475| 608.425
CH6| 612.600| 611.625| 611.725| 610.350| 612.250| 611.575| 613.275| 606.500| 608.000| 609.375
CH7| 613.100| 613.175| 613.350| 611.175| 612.975| 612.175| 606.875| 606.875| 608.525| 609.775
CH8| 607.550| 613.175| 610.475| 612.525| 613.400| 613.375| 609.325| 607.375| 609.225| 610.475
CH9| 607.550| 606.475| 612.050| 613.15| 611.775| 607.275| 610.775| 608.400| 610.275| 611.000
CH10| 611.200| 613.000| 613.450| 611.550| 606.550| 611.275| 610.475| 609.625| 611.075| 611.400

WARRANTY AND SERVICE

All SOUNDSATION products feature a limited two-year warranty. This two-year warranty is specific to the date of purchase as shown on your purchase receipt.
The following cases/components are not covered from the above warranty:

• Any accessories supplied with the product
• Improper use
• Fault due to wear and tear
• Any modification of the product effected by the user or a third party

SOUNDSATION shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at SOUNDSATION’s discretion either by repair or by exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of SOUNDSATION.
While under warranty period, defective products may be returned to your local SOUNDSATION dealer together with original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively you can send the product to SOUNDSATION SERVICE  CENTER – Via Enzo Ferrari , 10 – 62017 Porto Recanati – Italy . In order to send a product to service center you need an RMA number. Shipping charges have to be covered by the owner of the product.
For further information please visit www.soundsationmusic.com

WARNING

PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2202/96/EC) and your national law.
This product should be handed over to a designated collection point, e.g., on an authorized onefor-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE).
Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

DECLARATION OF CONFORMITY

V1.0-Nov.23

Importazione e Distribuzione Strumenti Musicali e Accessori
Via Enzo Ferrari, 10
62017 Porto Recanati – Italy
Tel:+39 071 7595011 Fax:+39 071 7595099
info@frenexport.it – www.frenexport.it
P.IVA E C.F. 1T00260710439
Banca BANCA DELLE MARCHE spa
IBAN IT84 MO60 5569 1310 0000 0001 952
TO: whom it may concern
EU DECLARATION OF CONFORMITY
We, FRENEXPORT SPA, of Via Enzo Ferrari, 10 – 62017 Porto Recanati (MC) Italy
Declare under our sole responsibility that following products:
Models: SOUNDSATION WF-U199 INEAR and WF-U199 RX
Description: UHF 99-Channel In-Ear Monitor Wireless Systems conform to the essential requirements of:

• General Product Safety Directive 2023/988/EU
• European Low Voltage Directive 2014/35/EU
• European EMC Directive 2004/108/EU
• European Radio Equipment Directive (RED) 2014/53/EU

comply with the following standards (depend on type of product):

• EN 60065:2002 + A1:2006 + A11:2008 + A2:2010 + A12:2011
• EN 62479:2010
• ETSI EN 301 489-1 V1.9.2 (2011-09)
• ETSI EN 301 489-9 V1.4.1 (2007-11)
•  ETSI EN 300 422-1 V1.4.1 (2011-08)
• ETSI EN 300 422-2 V1.3.1 (2011-08)

conform to Restricions of Hazardous Substances (RoHS 2) directive 2011/65/EC and related amendments.
Porto Recanati, 03/11/2023

****This product is imported in EU by
FRENEXPORT SPA – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy
www.soundsationmusic.com
Soundsation® is a registered trademark of FRENEXPORT SPA – Italy

www.soundsationmusic.com

References

• About | Music.com
• Making music accessible for all - Soundsation music

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>