SoundSation MOOD L100 100W Beam Moving Head Testa Mobile Beam User Manual

SoundSation MOOD L100 100W Beam Moving Head Testa Mobile Beam

Please read this manual carefully and proper take care of this manual.

Dear customer

First of all thanks far purchasing a SOUNDSATION® product. Our mission is to satisfy all possible needs of musical instrument, professional audio and lighting users offering a wide range of products using the latest technologies. We hope you will be satisfied with this item and, if you want to collaborate, we are looking for a feedback from you about the operation of the product and possible improvements to introduce in the next future. Go to our website www. soundsationmusic.com and send an e-mail with your opinion, this will help us to build instruments ever closer to customer’s real requirements.
One last thing: read this manual before using the instrument, an incorrect operation can cause damages to you and to the unit. Take care!

The SOUNDSATION Team

Important Safety Symbols

The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
The symbol is used in the service documentation to indicate that specific component shall be replaced only by the component specified in that documentation for safety reasons.
Protective grounding terminal
Alternating current/voltage
Hazardous live terminal
OFF   Denotes the apparatus is turned on
ON Denotes the apparatus is turned off
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.
CAUTION: Describes precautions that should be observed to prevent danger of the apparatus.
To protect the environment, please try to recycle the packing material as much as possible
The projector is for indoor use only, IP20. Use only in dry locations.
Keep this device away from rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or metallic objects.
Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls

Important Safety Instructions

• Read these instructions
• Keep these instructions
• Heed all warning
• Follow all instructions

Water / Moisture
This lighting is intended to indoor use only. To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable, explosive or corrosive materials surrounded in 10 meters while operating.

Heat
The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat. Fixture may carry high heat, do not aim at objective exceeding 2 minutes.
Ventilation
The unit must be installed in a location with adequate ventilation, at least 5m away from adjacent surfaces. Be sure that no ventilation slots are blocked.
Object and Liquid Entry
Objects do not fall into and liquids are not spilled into the inside of the apparatus for safety.
Installation
Always secure fixture using a safety chain and carrying handles. Never carry the fixture by its cord.
Power Cord and Plug
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two poles; a grounding-type plug has two poles and a third grounding terminal. The third prong is provided for your safety. If the provided plug does not fit into your outlet, refer to an electrician for replacement.
Power Supply
Always make sure that you are connecting to the proper voltage and the line voltage not higher than stated on the decal or rear panel of the fixture. Unplug this apparatus during lightning storms or when unused for long periods of time.
Fuse
To prevent the risk of fire and damaging the unit, please use only of the recommended fuse type as described in the manual. Before replacing the fuse, make sure the unit turned off and disconnected from the AC outlet.
Electrical Connection
Always disconnect from the power source before servicing or replacing fuse/ lamp and be sure to replace with same fuse/lamp size and type. Cut off power before moving, repairing and cleaning the machine. Improper electrical wiring may invalidate the product warranty.
To avoid electric shock, all fixtures must be connected to circuits with a suitable ground. Do not power on and power off the fixture in a short time.
DMX connection
When use DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source.
Cleaning
Clean only with a dry cloth. Do not use any solvents such as benzol or alcohol.
Servicing
In case of failure or misfunction occurred, stop using the unit immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Buy the same spare parts/components from manufacturer directly. Any damage that is caused by violating this manual is out of insurance, our company will not take the responsibility.
Warning
Avoid direct eye exposure to the light source while it is on.

Before You Start

UNPACKING

Thank you for purchasing MOOD L100 BEAM Moving Head. Every Moving Light has been well tested and has been shipped in perfect operating condition. Carefully unpack the box and check the contents to ensure that all parts are present and in good conditions.

• 1 Moving Head
• 1 DMX Cable (3pin XLR Male to Female)
• 1 Power cable (Power Con)
• 1 Omega Clamp
• 1 User manual

If anything damaged during transport, notify the shipper immediately and keep the packing material for inspection. Again, please save the carton and all packing materials. If the fixture must be returned to manufacturer, it is important that the fixture be returned in the original manufacturer box and packing.
Please do not take any action without first contacting us.

Getting started

The MOOD L100 BEAM Moving Head is part of a wider range of SOUNDSATION DMX intelligent Moving Head Lights. This light is compact and light weight and very easy to use. It is ideal for any rental job or installation. The unit can be controlled by any DMX controller or in standalone mode.
Make sure there is enough space around the unit for proper ventilation and prevent overheating; do not place the unit on top of hot devices such as radiators or power amplifiers. The console is connected to mains through the supplied cable. The product meets the required safety standards. Blown fuses must be replaced with fuses of the same type and specification.

Make sure that all units must be properly grounded. For your safety, you should never remove any ground connector from electrical devices or power cables, or make them inoperative.

FEATURES

MOOD L100 BEAM is a compact beam moving head equipped with a single 100W high- brightness white LED, extremely bright and reliable, with precise and silent Pan/Tilt movements.

• 100W high-brightness white LED with a 50.000 hours lifespan
• Color Wheel: 7 colors + White and Color rotation
• Gobo Wheel: 7 gobos + White and Gobo rotation
• Prism: Static and Rotating
• Beam Angle: 2,5°
• Electronic dimmer: 0-100%
• Strobe:1-20Hz
• Control mode : 12 CH, DMX512, Master/slave, Auto, Sound
• Pan/Tilt: 540° / 270°
• LED Display (English)
• Voltage: AC100V-240V – 50/60Hz
• Rated Power: 100W
• Mains socket: PowerCon
• Socket DMX IN: 3 pin XLR M
• Socket DMX OUT: 3 pin XLR F
• Stock: Clean and Dry place
• Running Temp.: 0-40°C
• Net Weight: 4 kg
• Fixture Size (WxDxH): 230 x 155 x 300 mm
• Gross Weight: 5 kg
• Packing size (WxDxH): 290 x 270 x 310 mm
  Note: Our products are subject to a process of continuous further development. Specifications are subject to change without notice

SETUP

Installation

Pay attention to the safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. The authorized dealer must only carry out the installation.

The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolishment. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.

When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation another time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a year.

WARNING: The fixture should not be installed in outside areas where persons may walk by or be seated.
IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, lnowledge of the installation material used, and periodic safety inspection of it and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead consult a professional structural rigger. Improper installation can result in bodily injury or property loss.

If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room. Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector’s weight.

CAUTION: Fixture may cause severe injuries when crashing down. If you have doubts concerning the safety of a possible installation, do not install the fixture!
CAUTION: Use two appropriate clamps to rig the fixture on the truss. Follow the instructions mentioned at the bottom of the base. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.
DANGER OF FIRE! When installing the device, make sure there is no highly inflammable material (decoration articles, etc.) within a distance of minimum 0.5 metre.

The moving-head light can be placed directly on the floor or rigged in any orientation on a truss without altering its operation characteristics. Use the rigging clamp to merge the M10 or M12 screw – please check the base.

Connections

Mains Connections
Connect the device to the mains with the power-plug. The wire correspondence is as follow:

The earth must to be connected! Pay attention to the safety!

Before taking into operation for the first time, the installation has to be approved by an expert.

DMX-512 Connection

The wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.
Only use a stereo-shielded cable and 3-pin XLR-plugs and connectors in order to control the fixture or one fixture with another.

If you are using the recommended controllers, you can connect the DMX-output of the controller directly with the DMX-input of the first fixture in the DMXchain. If you wish to connect DMX-controllers with other XLR-output, you need to use adapter-cables.

Building a Serial DMX Chain
Connect the DMX-output of the first fixture in the DMX-chain with the DMX- input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected.

A word on termination: DMX is a resilient communication protocol, however errors still occasionally occur. Termination reduces signal errors, and therefore best practices include use of a terminator in all circumstances. If you are experiencing problems with erratic fixture behavior, especially over long signal cable runs, a terminator may help improve performance.

To build your own DMX Terminator: Obtain a 120-ohm, 1/4-watt resistor, and wire it between pins 2&3 of the last fixture. They are also readily available from specialty retailers.

Complimentary signal cable can transmits signals to 20 unit fixtures at most. Signal amplifier is a must to connect more fixtures.

Master-Slave control mode
Set up one fixture as Master fixture (triggering) and other fixtures as Slave fixtures (receiving trigger signals). A fixture is automatically set as Master when it is the first in the DMX chain, and fixtures connected after it will behave as Slave units. Make sure that all fixtures have the same DMX address.

Front Panel

Front panel is composed by an LED display, a microphone, and four buttons (MENU, UP, DOWN, ENTER), which help the user to adjust all functions described in the following paragraphs. The fixture is really easy to be controlled.

Buttons

On numerical value: increases value
DOWN| In sub-menu: previous function
On numerical value: decreases value
ENTER| Enters function and confirms value

Rear Panel

From left to right:

• DMX IN: 3-poles XLR Male connector
• DMX OUT: 3-poles XLR Female connector
• Fuse Holder
• On/Off switch
• PowerCon power input

Control Menu

Press the “MENU” button to scroll through the functions, which are shown on the display. Press the “UP” and “DOWN” buttons to navigate the sub-menus and values, then press “ENTER” to confirm. Press the “MENU” button again to scroll through the next functions.

WARRANTY AND SERVICE

All SOUNDSATION products feature a limited two-year warranty. This twoyear warranty is specific to the date of purchase as shown on your purchase receipt.
The following cases/components are not covered from the above warranty:

• Any accessories supplied with the product
• Improper use
• Fault due to wear and tear
• Any modification of the product effected by the user or a third party

SOUNDSATION shall satisfy the warranty obligations by

remedying any material or manufacturing faults free of charge at SOUNDSATION’s discretion either by repair or by exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of SOUNDSATION.
While under warranty period, defective products may be returned to your local SOUNDSATION dealer together with original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively you can send the product to SOUNDSATION SERVICE CENTER – Via Enzo Ferrari , 10 – 62017 Porto Recanati – Italy . In order to send a product to service center you need an RMA number. Shipping charges have to be covered by the owner of the product.
For further information please visit www.soundsationmusic.com

WARNING

PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only

This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2202/96/EC) and your national law.
This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE).
Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

This product is imported in EU by
FRENEXPORT SPA – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy
www.soundsationmusic.com
Soundsation® is a registered trademark of FRENEXPORT SPA – Italy

References

• Making music accessible for all - Soundsation music

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>