Einhell GC-PM 40-2 S Petrol Lawn Mower Machine Instruction Manual

Einhell GC-PM 40-2 S Petrol Lawn Mower Machine

IMPORTANT INSTRUCTION

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care.
Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as
well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
Explanation of the warning signs on the equipment

•  Read the operating instructions.
•  Take care of the danger from catapulted parts. Keep a safe distance.
•  Danger! Sharp blades – Switch off the engine and pull the spark plug boot before doing any maintenance, repair, cleaning or adjustment work.
•  Fill with oil and fuel before starting the mower.
•  Caution: Wear ear protection and safety goggles.
•  Guaranteed sound power level.
•  Caution! Hot parts. Keep your distance.
•  Fill in fuel only when the engine is switchedoff .
•  Starting procedure
•  Engine start/stop lever (I=Engine on; 0=Engine off )
•  Drive lever (clutch lever)

Safety regulations

The corresponding safety information can be found in the enclosed booklet. Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fire and/or serious injury. Keep all the safety information and instructions in a safe place for future use.

Components

•  Layout and items supplied
•  Layout (Fig. 1-12)
•  Engine start/stop lever (engine brake)
•  Drive lever (clutch lever)
•  Fuel pump (primer)
•  Top and bottom push bar
•  Debris bag
•  Level indicator
•  Ejector fl ap
•  V-belt
• Tank fi ller cap
•  Oil fi ller screw
•  Cutting height adjustment
•  Starter cable
•  cable clip
•  Star nut (2x)
•  Long screw (2x)
•  Spark plug wrench
•  2x screws (bottom push bar)
•  Eyelet

Items supplied

Please check that the article is complete as specifi ed in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Proper use

• The equipment may only be used for the tasks it is designed to handle. Any other use is deemed to be a case of misuse.
• The user/operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
• The petrol lawn mower is intended for private use i.e. for use in home and gardening environments.
• Private use of the lawn mower refers an annual operating time generally not exceeding that of 50 hours, during which time the machine is primarily used to maintain small-scale, residential lawns and home/hobby gardens. Public facilities, sporting halls, and agricultural/forestry applications are excluded.
• Please note that our equipment has not been designed for use in commercial, trade or industrial applications.
• Our warranty will be voided if the equipment is used in commercial, trade or industrial businesses or for equivalent purposes.
• The operating instructions as supplied by the manufacturer must be kept and referred to in order to ensure that the lawn mower is properly used and maintained.
• The instructions contain valuable information on operating, maintenance and servicing conditions.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.

Residual risks

Even if you use this electric power tool in accordance with instructions, certain residual risks cannot be rules out. The following hazards may arise in connection with the equipment’s construction and layout:

•  Damage to hearing if no suitable ear protection is used.
•  Health damage caused by hand-arm vibrations if the equipment is used over a prolonged period or is not properly guided and maintained.

Assembling the components

Some parts of the equipment come disassembled. For quick and easy assembly, read and follow the instructions below.
Note! You will need the following additional tools (not supplied) for assembly, and also for maintenance work:

• One flat oil drip tray (for changing the oil)
• One 1 liter measuring jug (oil/petrol resistant)
• One petrol can
• One funnel (suitable for the tank’s petrol filler neck)
•  Household wipes (to wipe up oil/petrol residue; dispose of these at a filling station)
• One petrol suction pump (plastic, available from DIY stores)
• One oil can with hand pump (available from DIY stores)
• Engine oil

Assembly

•  Fit the lower and upper push bar (Item. 3) 
•  Insert the grip of the starter cable (Item 9) into the hook provided for that purpose
•  Fasten the actuator cables to the push bar with the supplied cable clips (Item 10)
•  Lift the ejector fl ap (Item 5a) with one hand and hook in the grass bag (Item 4a)

Adjusting the cutting height

• Adjust the cutting height only when the engine has been switched off .
• The cutting height is centrally adjusted with the cutting height adjustor lever
• Different cutting heights can be selected.
•  Actuate the adjustor lever and pull it to the required position. Let the lever click into position.

Operation

• *  The engine comes without oil and petrol. Therefore, be sure to add oil and petrol before starting the engine.

  •  Check the oil level (see 7.2.1).
  •  Use a funnel and measuring jug to fi ll the tank with petrol. Make sure that the petrol is clean. Warning: Never use more than one safety petrol can. Do not smoke when refueling. Switch off the engine before refueling and allow the engine to cool down for a few minutes.
  •  Ensure that the ignition cable is connected to the spark plug. Carrying out a safety test on the engine start/ stop lever
  • The lawn mower comes equipped with an engine start/stop lever (Fig. 5a/Item 1a) in order to prevent it from starting up unintentionally and to ensure that the engine and blade stop quickly in case of danger.
  • The lever must be actuated   before the lawn mower is started.

• When the engine start/stop lever is released, it must return to its initial position

• Before you start mowing, you should run through this process several times in order to ensure that the lever and actuator cables are working properly

• Repeat the test several times after the engine has started up.

• When the engine start/stop lever is released, the engine must stop within a few seconds.

• If not, contact Customer Service. Danger: The blade begins to rotate as soon as the engine is started.

Starting the engine

•  Ensure that the ignition cable is connected to the spark plug.
•  Press the fuel pump (primer) (Fig. 6/Item 2) three times. You can skip this point if the engine has already warmed up.
•  Stand behind the lawn mower. Actuate the engine start/stop lever   with one  hand. The other hand must be on the starter handle.
•  Start the engine using the reversing starter (Fig. 1/Item 9). To do this pull out the handle approx. 10 –15 cm (until you feel a resistance) and then start the engine with a sharp tug. If the engine does not start, tug the handle again.
• Never allow the actuator cable to snap back.
• In cold weather, it may be necessary to repeat the starting process several times.

Drive unit

Drive lever/clutch lever  : If you press this the clutch for the drive will be closed and the lawnmower will start to move with the engine running. Release the drive lever in good time to stop the moving lawnmower. Practice starting and stopping before you use the mower for the fi rst time until you are familiar with controlling the mower.

Tips on mowing properly

Never open the chute fl ap when the grass bag has been detached (to be emptied) and the engine is still running. The rotating blade can cause serious injuries! Always carefully fasten the chute flap and  debris bag. Switch off the engine before you remove them.Whenever you need to perform any kind ofadjustment, maintenance or repair work, switch off the engine and wait until the blade no longer rotates. Pull off the spark plug connector.

Mowing
The engine is confi gured for an optimal grass cutting speed, for ejecting grass into the debris bag, and for many years of use. Only use a sharp blade that is in good condition. This will prevent the grass blades from fraying and the lawn from turning yellow. Try to mow in straight lines for a nice, clean look. The swaths should overlap each other by a few centimeters in order to avoid stripes. Keep the underside of the mower housing clean and remove grass build-up. Deposits not only make it more diffi cult to start the mower; they decrease the quality of the cut and make it harder for the equipment to bag the grass. Always mow along inclines (not up and down). You can prevent the lawn mower from slipping down by holding a position at an angle upwards. Select the cutting height according to the length of the grass. If necessary, mow a number of times so that you never cut more than 4cm of grass in one go. Switch off the engine before doing any checks on the blade. Keep in mind that the blade continues to rotate for a few seconds after the engine has been switched off . Never attempt to manually stop the blade. Regularly check to see if the blade is securely attached, is in good condition and is sharp. If the contrary is the case, sharpen the blade or replace it. In the event that the blade strikes an object, immediately switch off the lawn mower and wait for the blade to come to a complete stop. Then inspect the condition of the blade  and the blade mount. Replace any parts that are damaged.

Switching off the engine

All you have to do to switch off the engine is release the engine start/stop lever   Pull off the spark plug connector fromthe spark plug in order to prevent the engine from starting. Before you start the engine again, check the cable of the engine brake. Check that theactuator cable is correctly fi tted. If the switch-off cable is kinked or damaged, it must be replaced.

Emptying the debris bag

When the debris bag is full, the air throughput will be low and the level indicator (4b) will be up close against the debris bag  . Empty the debris bag and clear out the ejector chute  Before taking  off the debris bag,switch off the engine and wait until the blade has come to a stop. To take off the grass basket, use one hand to lift up the chute fl ap and the other to grab onto the basket carry-handle. Remove the basket   For safety reasons, the chute fl ap automatically falls down after removing the grass basket and closes off the rear chute opening. If any grass remains in the opening, it will be easier to restart the engine if you pull the mower back approximately 1m. Do not use your hands or feet to remove clippings in or on the mower housing, but instead use suitable tools  such as a brush or a hand broom.In order to ensure that the majority of grass clippings are picked up, the inside of both the grass bag and especially the air grill must be cleaned after each use. Reattach  the grass bag only when the engine is switched off and the blade is stopped.Using one hand, lift up the chute fl ap, while grabbing onto the basket handle with the other. Hang in the basket from the top.

7. Cleaning, maintenance, storage, transport and ordering of spare parts
Never work on or touch any current-conducting  parts of the ignition system while the engine is running. Pull the spark plug boot from the spark boot before doing any maintenance or assembly work. Never carry out any work on the equipment while the engine is running. Work that is not described in these operating instructions, should only be carried out by authorized workshops.

Cleaning

The lawn mower should be cleaned thoroughly every time after it has been used. This applies in particular to its underside and the blade mount. Tilt the lawn mower to the rear by pressing down the push bar. Note: Before tilting the lawn mower, use a petrol extraction pump to drain all the fuel out of the fuel tank. Do not tilt the lawn mower by more than 90 degrees. It is easiest to remove dirt and grass immediately after mowing. Dried grass remnants and dirt may impair the mowing operation. Check whether the grass ejector chute is free of grass residues and clear out as required. Never clean the lawn mower using a water jet or a high-pressure cleaner. Ensure that no water can get into the interior of the equipment. Do not use aggressive cleaning agents such as cold cleaners or petroleum ether. Maintenance Please refer to the supplied petrol service manual for information on the maintenance intervals. Note: Dispose of soiled maintenance material and operating materials at the appropriate collection point.

Petrol engine

Note! Never run the engine with no or too little oil. This can cause serious damage to the engine. Checking the oil level Place the lawn mower so that it stands level. Unscrew the oil dipstick     by turning it counter-clockwise and wipe the dipstick. Reinsert the dipstick into the fi ller opening as far as it will go but do not screw it in. Pull out the dipstick, hold it horizontally and read off the oil level. The oil level must be between the two marks min. and max. on the oil dipstick

Changing the oil

• The engine oil is best changed when the engine has been switched off but is still warm.
•  Make sure that the debris bag has been removed.
•  Empty the petrol tank with a petrol suction pump and run the engine until the remaining fuel is fully consumed.
•  Place an oil drip tray alongside the mower.
•  Open the oil fi ller plug (Item 7) and tilt the mower 90° sideways.
•  The hot oil will fl ow through the open oil fi ller opening into the oil drip tray.
•  After the old oil has drained out, set the mower upright again.
•  Fill in engine oil up to the top mark on the oil dip stick.
•  Important! Do not screw in the oil dipstick to check the oil level – only insert it as far as the thread.
•  Dispose of the used oil in accordance with applicable regulations.

Blades

For safety reasons, have all blade sharpening balancing and mounting work carried out by an authorized service center. To achieve optimal results, we recommend having the blades checke once a year. Changing the blades (Fig. 8) When changing the cutting unit, be sure to usonly genuine replacement parts. The identifi cation mark on the blade must correspond with the number specifi ed in the spare parts list.Never install a blade from a diff erent manufacturer.

Damaged blades

If, in spite of all caution, the blade comes into contact with an obstacle, switch off the engine immediately and pull off the spark plug connector. Tilt the lawn mower to the rear and check theblade for damage. Damaged or bent blades mustbe replaced. Never straighten a bent blade. Never work with bent or heavily worn blades as this wil result in vibrations, causing further damage to the mower.

Axles and wheel hubs

Grease should be applied to the axles and wheel hubs once per season. To do so, remove the wheel caps with a screwdriver and loosen the fastening screws on the wheels. Care and adjustment of the actuator cables Oil the actuator cables at regular intervals and check that they move easily.

 Maintenance of the air filter

Soiled air fi lters reduce the engine output by supplying too little air to the carburetor. If the air contains a lot of dust, the air fi lter must be checked more frequently. Never clean the air fi lter with petrol or infl ammable solvents. Clean the air fi lter only with compressed air or by tapping it.

Maintenance of the spark plug

• Clean the spark plug with a copper wire brush.
•  Pull off the spark plug connector
•  Remove the spark plug using a spark plug wrench.
•  Assemble in reverse order.
• Inspecting the V-belt Remove the blade as described in 7.2.2. To inspect the V-belt you must remove the V-belt cover 

Repairs

After carrying out any repair or maintenance work, ensure that all safety parts are installed and in perfect condition. Keep potentially hazardous parts out of reach of other persons and children.
Note! In accordance with the German Product Liability Act, we are not liable for any damages if they result from improper repairs to the product or if parts are replaced by items other than genuine parts or parts approved by us. Furthermore, we are not liable for any damages if they result from improper repairs to the product. Arrange for your customer service or an authorized workshop to do the work.

Operating times

Please observe the regulations concerning lawn mower operating times, which may diff er from town to town.

Preparing the mower for long-term storage

• Warning! Do not empty the petrol tank in enclosed areas, near fi re or when smoking. Petrol fumes can cause explosions and fi re.
•  Drain the petrol tank using a petrol extraction pump.
•  Start the engine and run it until the tank and fuel line are completely empty and the engine stalls.
•  Change the oil after each season.
•  Remove the spark plug. Use an oil-can to fill the cylinder with approx. 20 ml of oil. Slowly pull back the starter handle, which will bathe the cylinder wall with oil. Screw the spark plug back in.
•  Clean the cooling fi ns of the cylinder and the housing.
•  Be sure to clean the entire equipment to protect the paint.
•  Store the equipment in a well-ventilated place.

Preparing the mower for transport

• Do not empty the petrol tank in enclosed areas, near fi re or when smoking. Petrol fumes can cause explosions and fi re.
•  Drain the petrol tank using a petrol extraction pump.
•  Always let the engine run until it has used upthe remainder of petrol in the tank.
•  Empty the engine oil from the warm engine.
•  Remove the spark plug connector from the spark plug.
•  Clean the cooling fi ns of the cylinder and the housing.
•  Unhook the starter cable from the hook   Slacken the connection  on the left and right of the push bar and swing down the upper push bar. Make sure that the actuator cables do not get kinked when the bar is pulled up.
•  Wedge a few layers of corrugated cardboard between the upper and lower push bars and the engine in order to prevent any chafi ng.
•   Secure the load suffi ciently so that it cannot slip and cause damage or injuries during transportation.Consumables, wear materials and spare parts Spare parts, consumables and wear materialssuch as engine oil, V-belts, spark plugs, air fi lter inserts, petrol fi lters, batteries and blades are not covered by the warranty. Ordering replacement parts: Please quote the following data when ordering replacement parts:
  •  Type of machine
  •  Article number of the machine
  •  Identification number of the machine
  •  Replacement part number of the part required
  • For our latest prices and information please go to www.Einhell-Service.com

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or  recycled. The equipment and its accessories aremade of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts ofsuch a collection point, you should ask in your local council offi ces.

Troubleshooting guide

Service information

We have competent service partners in all countries named on the guarantee certifi cate whose contact details can also be found on the guarantee certifi cate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables. Please note that the following parts of this product are subject to normal or natural wear and that the
following parts are therefore also required for use as consumables..

Warranty certificate

• Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the addres  shown on this guarantee card. You can also contact us by telephone using the service number shown.Please note the following terms under which guarantee claims can be made:
•  These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not aff ected by this guarantee. Our guarantee is free of charge to you.
•  The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectifi cation of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
•  The following are not covered by our guarantee:
  •  Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
  •  Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
  •  Damage to the device or parts of the device caused by normal or natural wear or tear or by normaluse of the device.
•  The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period.The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fi tted will not result in an extensionof the guarantee period, and no new guarantee will become active for the work performed or parts fitTed. This also applies if an on-site service is used.
•  To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identifi cation will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned  you or we will send you a new replacement. Of course, we are also happy off er a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.

References

• Einhell Service
• Einhell Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>