TRAXON Static White 100W AC Allegro Washer Installation Guide
- June 1, 2024
- traxon
Table of Contents
TRAXON Static White 100W AC Allegro Washer
Product Specifications
- Model : Allegro Washer AC 100W
- Mounting Guide Dimensions:
- Width: 20mm/0.8″
- Height: 170mm/6.7″, 340mm/13.4″
- Depth: 13mm/0.5″
- Hex Screw Size: R6.5mm/0.3″, 252mm/9.92″
- Minimum Distance to Obstacle : > 1.25m
- Mounting Bracket Dimensions: 310mm/12.2″, 395mm/15.6″
Product Usage Instructions
- Tilt the head slightly to mount the bracket. Only turn enough to unlock.
- Do not unscrew the hex screw from the fixture.
- Adjust the position as needed.
- Use a 6mm Hex Key for tightening torque of 3.5Nm.
- Optional: Use a stainless steel safety cable (not included) with specifications of 1.5 – 2.3mm / 0.06 – 0.09″.
- Avoid obstructing the vent hole.
- For connectors, avoid vertical placement if possible. If unavoidable, follow bending radius guidelines.
- Remember to tighten the cable gland after installation, ensuring it tightens the cable sheath.
FAQ
-
Can I use any size of hex screw for mounting the bracket?
No, it is recommended to use a 12mm screw (X3) for mounting the bracket. -
What is the purpose of the optional stainless steel safety cable?
The safety cable provides additional security and support for the washer unit. -
Are there specific connectors recommended for this product?
Yes, field-installable connectors such as XB.AC.3106000 and XB.AC.4006000 are suitable for cable OD sizes mentioned in the manual.
Dimensions
Installation Instructions
Allegro Washer AC 1 00W Mounting Guide
Applicable to Field Installable Connectors
To properly bend the cable
- Cable must NOT bent below the Minimum Bending Radius (4 x Cable Diameter) as specified by the cable manufacturer and the nonbendable length of 5cm near the connector end MUST be adhered to.
- Note the minimum bending radius for conductors > 1.5mm?.
- Pull forces on the contact points can be avoided by bending the wire as required.
Avoid vertical placement of the connectors.
If vertical installation is unavoidable:
-
Add silicone glue on the surface of the cable gland.
-
Layout the cable to have a drip loop to allow water to run off the wire.
-
XB.AC.3106000 (for cable OD 6-10mm)
-
XB.AC.4006000 (for cable OD 10-14mm)
-
3-pin Field Installable AC Female Connector IP66
-
XB.AC.2302000
-
5-pin Field Installable AC Male Connector IP66 (for cable OD 10-14mm)
-
XB.AC.2303000
-
5-pin Field Installable AC Female Connector IP66 (for cable OD 10-14mm)
-
Remember to tighten the cable gland after installation.
-
Make sure the cable gland also tightens the cable sheath.
CONNECT TO THE POWER SUPPLY UNDER NATIONAL REGULATIONS
- IF THE EXTERNAL FLEXIBLE CABLE OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR A SIMILAR QUALIFIED PERSON TO AVOID ANY HAZARD.
- INSTALLATION/MAINTENANCE ONLY BY SKILLED PERSONNEL.
- DURING OVERHAUL/MAINTENANCE ONLY USE ORIGINAL PARTS.
- IF ANY LUMINAIRE IS SUBSEQUENTLY MODIFIED, THE PERSON RESPONSIBLE FOR THE MODIFICATION SHALL BE CONSIDERED THE MANUFACTURER.
- THE MANUFACTURER BEARS NO LIABILITY FOR DAMAGE CAUSED BY INAPPROPRIATE USE OR APPLICATION.
- THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
- THE LUMINAIRE SHOULD BE POSITIONED SO THAT PROLONGED STARING INTO THE LUMINAIRE AT A DISTANCE CLOSER THAN 7M IS NOT EXPECTED.
CONTACT
©2023 TRAXON TECHNOLOGIES. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT ®, ARE
TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS,
OTHER PATENTS PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
www.traxon-ecue.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>