BOCCI 100.1mi Pendant Light Installation Guide
- June 3, 2024
- BOCCI
Table of Contents
BOCCI 100.1mi Pendant Light
DIMENSION
SPECIFICATION
PENDANTS: one
MOUNTING: mini innie canopy (mud-in). 35mm (1.4”) in diameter (exposed),
88mm (3.5”) in diameter (overall) x 35mm (1.4”)
LAMPING: 1.5w LED (2000K, 2500K, 3500K)
COAX: adjustable 3000mm (10’) standard / up to 30500mm (100’) maximum
MATERIALS: blown glass, braided metal coaxial cable, electrical
components, white polyurethane canopy
WEIGHT: approximately 2.75kg (6.1lb)
POWER SUPPLIES: remote mounted (fixture does not hook directly to a
junction box). Power supplies included
DESCRIPTION
The 100.1mi is a single 100 pendant fixture with a miniinnie canopy size. The
miniinnie canopy is 35mm (1.4”) in diameter (exposed), 88mm (3.5”) in diameter
overall, and 35mm (1.4”) deep, which is meant to be mudded into drywall. The
pendant drop lengths on this light fixture are adjustable up to the specified
maximum.
Note: not adjustable after drywall is finished. 100 brings multiple glass
artists together in a performative act. Molten glass bubbles are prepared and
then smashed together to produce unpredictable interlocking glass forms.
NOTES
+ Purchase replacement lamps online at www.bocci.com/shop/bulbs
+ All chandeliers will be outfitted with 2500K lamps if not specified.
+ Requires power supplies to be remote mounted.
PRODUCT INSTALLATION INSTRUCTIONS
-
Very carefully uncoil the braided coaxial cable in a spool like manner. Insert your index fi ngers into opposite sides of the roll then rotate your fi ngers around each other to unrollthe coaxial cable. Use patience: allow thecable to uncoil completely to avoid kinks. Thread the coaxial cable through the canopy.Drill a 45mm (1.7”) diameter hole in ceiling material. Pull low voltage house wire through the hole. Note: This low voltage wire will run to a remote mounted power supply.
-
Determine the overall drop for the pendant fixture. Use the 2mm Allen key to loosen the setscrew in the canopy and gently feed the cable through until you have reached your desired drop length. Use Allen key to tighten the setscrew to hold the strain relief and secure the coaxial cable at its new length. Perform a gentle tug test to ensure it is secure. DO NOT OVERTIGHTEN. Note: The strain relief is a black plastic collar around the coaxial cable. There is a single slot opening on the side of the strain relief component. It is essential that the opening is oriented at 90 degrees to set screw chamber. There can be no contact between the set screw and the cable
-
Connect the black wire to black and white wire to white wire. Connect the house wires to the coaxial cable using #16 butt splices (stagger the splices). Use raw butt splices and heat shrink to simplify the installation. For multiple pendant installations, ensure that the braided outer wires are all connected to one 12V output wire and all inner insulated wires are connected to the other or a short will occur.
Note: Insulated core is positive and braided exterior is negative. Affix minizine canopy to ceiling surface with fasteners provided. Turn power to fixture on. -
Step 1: Attach the lamp holder to the pendant hardware with set screw provided. Plug the lamp into lampholder and slide on the diffuser. Do not touch the lamp with your bare hands. Ensure power to lamp is working correctly
-
Tape the mounting plate edges with fi er mesh drywall tape
Note: mask the coaxial cable off with painters tape to help with cleanup. -
Use a drywall filler compound to “mud over” the assembly. Use the raised edge to mud up to to establish a sharp edge and to avoid getting mud in the indentation Feather from the center of the mounting plate outwards using a large drywall trowel.
-
Using a foam sanding block, sand entire area until the rim and the edge of the operative component are exposed. For long term performance, it is essential that mud is sanded right down to the plastic rim. Paint over entire assembly.
-
Please note that the crisp cut edges of the 100 pendants are fragile and can chip if not handled with care when installing and cleaning. Bocci recommends wearing gloves during the installation. The edges of the glass may be sharp to handle.
-
Step 2: Insert the pendant hardware assembly into the pendant.
Step 3: Tighten the 3 screws until they are fully engaged (refer to illustration above)
-
Give the pendant a gentle pull to ensure the screws are locked onto the pendant. Slide cover cap onto the coaxial cable and place into the inset portion of the pendant hardware.
-
The cap should sit fl at on the pendant hardware. If the screws are sticking out and the cap isn’t sitting fl at on the pendant hardware, please check to ensure the screws are fully engaged. Refer to step 8 & 9 for more details.
-
- Clean fingerprints from surfaces.
For additional assistance,
please contact Bocci:
vancouver
sales@bocci.com
www.bocci.com
**Berlin
europe@bocci.com
www.bocci.com
US Patent Pending
EU Patent # 008526131-0001
Made in Vancouver, Canada
LOW VOLTAGE LUMINAIRE
E476186
© 2021, Bocci Design and Manufacturing Inc. All rights reserved. Any inquiries
should be directed to: info@bocci.com
US Patent Pending
EU Patent # 008526131-0001
**
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>