AMERICAN LIGHTING P5401-718-L LED Pendant Installation Guide

P5401-718-L LED Pendant

Product Information: LED Pendant Light Fixture (P5401-718-L)

The LED Pendant Light Fixture (P5401-718-L) is a modern and stylish lighting solution for your home or office. It comes with a mounting plate, ground screw, and mounting screws for easy installation. The fixture is dimmable with ELV and/or LED compatible wall dimmer switches.

Installation Instructions

WARNING: Before installing the fixture, shut off power at the fuse box or circuit breaker.

1. Remove the old fixture, including the mounting hardware.
2. Carefully remove the fixture from the carton and check that all parts are included as shown in Figure 1.
3. Unscrew screws (G) to remove mounting plate (A) from canopy (F).
4. Position mounting plate (A) on the ceiling and attach it to the junction box (not included) using the mounting screws (B, size 8#-32N 1). The side of the mounting plate marked GND must face out as shown in Fig.1.
5. Connect the electrical wire as shown in Fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the ground wire from the fixture to it. Otherwise, connect fixture ground wire directly to the mounting plate (A) using the green screw (D) provided. Tuck the wire connections neatly into the ceiling junction box.
6. Slide canopy (F) over mounting plate (A) and secure it with screws (G).
7. Unscrew finial (J). Slide glass shade (E), acrylic diffuser (H), and gold decorative piece (I) to the lamp body (L) and secure it with finial (J).
8. Finally, tear off the protective film at the bottom of canopy (F).

CAUTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the frame only.

IMPORTANT: Fixtures should be installed by a qualified electrician to ensure proper wiring and installation.

INSTALLATION INSTRUCTIONS FOR P5401-718-L For LED Pendant

ASSEMBLING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker. Remove the old fixture including the mounting hardware.

2. Carefully remove the fixture from the carton and check that all parts are included as show in Figure 1.

3. Unscrew screws (G) to remove mounting plate (A) from canopy (F). Position mounting plate (A) on the ceiling and attached to the junction box (not included) using the mounting screws (B, size 8#-32N 1″). The side of the mounting plate marked “GND” must face out as shown in Fig.1.

4. The length of the power cord can be adjusted by loosening the set screw (S), then tighten the set screw (S).
   CONNECTING THE WIRES (Fig. 2)

5. Connect the electrical wire as shown in Fig 2. Making sure that all wire connectors and secured. If your junction box has a ground wire (green or bare copper), connect the ground wire from the fixture to it. Otherwise connect fixture ground wire directly to the mounting plate (A) using the green screw (D) provided. Tuck the wire connections neatly into the ceiling junction box.
   FINISHING THE INSTALLATION (Fig.1)

6. Slide canopy (F) over mounting plate (A) and secure with screws (G).

7. Unscrew finial (J). Slide glass shade (E), acrylic diffuser (H), and gold decorative piece (I) to the lamp body (L) and secure with finial (J).

8. Finally, tear off the protective film at the bottom of canopy (F).

Your installation is now complete. Return power to the junction box and test the fixture.

CAUTION/ATTENTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the frame only.

IMPORTANT: Fixtures should be installed by a qualified electrician to ensure proper wiring and installation.

Dimmable with ELV and/or LED compatible wall dimmer switches.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>