american lighting association 71265-66 Harbor View 1-Light Black Outdoor Wall Light Instruction Manual
- October 30, 2023
- american lighting association
Table of Contents
american lighting association 71265-66 Harbor View 1-Light Black Outdoor
Wall Light
Product Information
The product is a Model# 71265-66 fixture that is suitable for wet location applications. It comes with a mounting plate, ground screw, mounting screws, back plate, gaskets, screws, and a medium base bulb. The fixture should be connected to an outlet box and the electrical wires should be connected with connectors. The fixture has a maximum wattage rating of 60 Watts, and the glass can be replaced if needed.
Product Usage Instructions
- Ensure that the power is shut off at the fuse box or circuit breaker box before starting the installation.
- Remove the old fixture including the mounting hardware and carefully unpack the new fixture, laying out all the parts in a clear area.
- Attach the mounting plate to the outlet box using outlet box screws. The side of the mounting plate marked GND must face out.
- Connect the electrical wires as shown in Fig.2 with connectors, making sure that all wire connectors are secured. Connect the fixture’s ground wire to the outlet box’s ground wire or directly to the mounting plate using the green screw provided.
- Place the back plate over the mounting plate and secure it with two screws.
- To prevent moisture from entering the outlet box, use clear silicone sealant to outline the outside of the fixture’s back plate where it meets the wall leaving a space at the bottom to allow moisture a means to escape.
- To replace the glass, remove the gaskets and loosen the screws to remove the cover. Insert the new glass into the fixture frame from the bottom and secure the lower cover by screwing screws until tight and reinstalling the gaskets on the lower cover.
- Install one medium base bulb up to 60 Watts, or CFL or LED equivalent, in accordance with the fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING.
- Ensure that the installation is complete and return power to the outlet box. Test the fixture to ensure it is working correctly.
INSTALLATION INSTRUCTIONS
WARNING! SHUT THE POWER OFF AT THE FUSE OR CIRCUIT BREAKER.
PREPARING FOR INSTALLATION (Fig. 1)
- Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
- Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
- Attach mounting plate (B) using outlet box screws (F) to the outlet box (A) (not supplied). The side of mounting plate marked “GND” must face out. (Fig 1)
- CONNECTING THE WIRES (Fig. 2)
- Connect the electrical wires as shown in Fig.2 with connectors (E), making sure that all wire connectors are secured. If your outlet box (A) has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw (D) provided. After the wires are connected, carefully tuck them inside the outlet box (A).
- FINISHING THE INSTALLATION (Fig. 1)
- Place the back plate (G) over the mounting plate (B) and secure it with two screws (C). Tighten until snug (Fig 1).
- To prevent moisture from entering the outlet box (A) and causing a short, use clear silicone sealant to outline the outside of the fixture back plate (G) where it meets the wall leaving a space at bottom to allow moisture a means to escape. (Fig.3)
- To replace the glass, remove gaskets (M, 8pcs) and loosen the screws (L, 8pcs) to remove cover (K). Insert the new glass (J) into the fixture frame from the bottom. Secure the lower cover (K) by screwing screws (L, 8pcs) until tight and reinstalling gaskets (M, 8pcs) on the lower cover (K).
- Install (1) one medium base bulb (I) up to 60 Watts, or CFL or LED equivalent (not included), in accordance with the fixture specification. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING) (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
- This fixture is ETL listed for wet location applications.
Your installation is now complete. Return power to the outlet box and test the fixture.
CAUTION-RISK OF FIRE CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR”
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>