VEVOR HJXZ30KG-110VTXCZV1 Stainless Steel Rotary Welding Positioner Owner’s Manual
- May 21, 2024
- VEVOR
Table of Contents
HJXZ30KG-110VTXCZV1
Stainless Steel Rotary Welding Positioner
Owner’s Manual
HJXZ30KG-110VTXCZV1 Stainless Steel Rotary Welding Positioner
IMPORTANT: Read these instructions before installing, operating, or servicing this product.
INTRODUCTION
WARNING： A procedure, which, if not properly followed, may cause injury
to the operator or others in the operating area.
Equipment Identification
The identification number specification or model, and serial number of this
unit usually appears on a nameplate attached to the control panel, record
these numbers for future reference.
Receipt of Equipment
When you receive the equipment, check it against the shipping documents, Make
sure it is complete and inspect the equipment for possible damage during
shipping, if there is any damage, notify the carrier immediately to file a
claim.
Furnish complete information concerning damage claims or mistake(s) in
shipment to our company Include the equipment identification number along with
a description of the parts in question.
Move the equipment to the installation site before uncrating the unit. Use
care to avoid damaging the equipment when using bars, hammers, etc. to uncrate
the unit.
SPECIFICATION
No| MODEL| UNIT| HD-30| HD-50| HD-100|
HD-200| HD-300
---|---|---|---|---|---|---|---
1| Power input| /| AC110V 50Hz| AC220V 50Hz| AC220V 50Hz| AC220V 50Hz| AC220V
50Hz
2| Horizontal loading capacity| Kg| 30| 50| 100| 100| 300
3| Vertical loading capacity| Kg| L^| 25| 50| 50| 150
4| Working table diameter| mm| 310| 310| 400| 400| 500
5| Working table height| mm| 380| 380| 520| 520| 650
6| Working table tilting angle| °| 0-90| 90| 90| 0-90| 90
7| Working table rotation speed| r/min| 1-15| 0.57| 0.57| 0.5-7| 0.2-2.5
8| Rotation motor| W| 80| 120| 120| 120| 200
9| Overall length (A)| mm| 380| 380| 490| 490| 680
10| Overall width (B)| mm| 380| 380| 530| 530| 660
11| Overall height (C)| mm| 380| 380| 520| 520| 650
12| Cable terminal| /| 30-50mm2| 30-50mm2| 30-50mm`| 30-50nd| 30-50nd
13| Table Centre Through Hole Dia| mm| 25| 25| 45/75/140| 45/75/140| 90
14| Net weight| Kg| 35| 35| 70| 78| 102
15| Applicable chuck| /| KD/80-200| KD/80- 200| KD-200/300| KD-200/300|
KD-300/400
DEMENSIONS
NOTE：
- HD-50: E=340mm F=320 mm
- HD-100: E=480mm F=400mm
- HD-200: E=480mm F=400mm
- HD-300: E=590mm F=475mm
- LUBE HOLE: Pour lubricating oil per week.
- DROP LOCK: Holding locking screw tightly when choose working table angle.
CONTROL PANEL FRONT PANEL：
K1: POWER ON/OFF SWITCH
K2: FORWARD/REVERSE SWITCH
K3: POWER PLIOT
K4: SPEED ADJUSTMENT
TROUBLE SHOOTING GUIDE
| NO. | SYMPTOM | POSSIBLE CAUSE | REMEDY |
|---|---|---|---|
| 1 | Power pilot does not lit | 1. Power fuse is burnt. |
2. LED burnt.
3. Power switch is burnt.
4. No power input.| 1. Replace a new fuse.
2. Replace LED.
3. Replace switch.
4. Check the switch or replace.
2| Speed Adjustment no Motion.| 1. Damaged potentiometer.
2. Motor control PCB no output.| 1. Check if potentiometer is 101CO3
otherwise replace.
2.Replace a new motor control PCB.
3| Foot switch no motion| Foot switch is damaged.| Check the foot switch or
replace.
4| Forward/Reverse no output| Forward/Reverse switch is damaged.| Check the
switch or replace.
5| Motor no motion| 1. Motor has power input but no motion.
2. Motor control PCB has no power input
3. Motor control PCB is damaged.| 1. Replace a new motor.
2. Check the transformer or replace.
3. Replace control PCB.
ILLUSTRATION OF THE CONTROL PCB ADJUSTMENT
-
Attention when choose the switches of input and output voltage（115V/230V), disconnect the power timely when doing the switch.
-
ACCEL is time accelerateing adjustable potentiometer
When the output voltage is 0-90VDC, from 0.5 seconds to 11 seconds can be adjustable; When the output voltage is 0-180VDC, from 0.5 seconds to 22 seconds can be adjustable. -
DECEL is decelerating adjustable potentiometer.
When the output voltage is 0-90 VDC, the longest time is 13 seconds; When the output voltage is 0-180VDC, the longest time is 25 seconds. -
MAX SPD is maximal speed adjustable potentionmeter; Twist it to the end clockwise to set the maximum speed.
-
MIN SPD is minimum speed adjustable potentionmeter; Twist it to the end clockwise to set the zero speed anticlockwise.
-
INHIBIT is external enable control side, When this function works,the speed of motor is set by MIN SPD.
-
TORQUE、IRCOMP are torque and laden adjustable potentiometer.
CONTROL SCHEMATIC DIGRAM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>