ZURN 500XLFC Water Pressure Reducing Valve with Flanged Connections Instruction Manual
- June 7, 2024
- ZURN
Table of Contents
ZURN 500XLFC Water Pressure Reducing Valve with Flanged Connections
Application
Zurn Wilkins model 500XLFC is designed for installation on potable water lines to reduce high inlet pressure to a lower outlet pressure. The high flow capacity makes this device most suitable for industrial water lines and commercial water systems. The balanced piston design enables the regulator to react in a smooth and responsive manner to changes in system flow demand, while at the same time, providing protection from inlet pressure changes
Approvals
- Meets the requirements of NSF/ANSI/CAN 61
Materials
| Body & cover | Low Lead Cast Bronze, ASTM B 806 |
|---|---|
| Bell housing | Cast Bronze, ASTM B 584 |
| Stem & plunge | Low Lead Cast Bronze, ASTM B 806 |
| Internals | Stainless steel, 300 Series |
| Elastomers | EPDM (FDA approved) Buna Nitrile (FDA approved) |
| Polymers | Delrin™ |
| Springs | Oil tempered wire, ASTM A229, Epoxy Coated |
| Cap gasket | Natural Vulcanized Fiber |
| Seat | Stainless steel, 300 Series |
Features
| Sizes | 2”, 21/2”, 3” |
|---|---|
| Maximum working water pressure | 300 psi |
| Maximum working water temperature | 140° F |
| Reduced pressure range (standard) | 25 psi to 75 psi |
| End connections (flanged) | ANSI Class 125 |
Options (Suffixes can be combined)
- 510XLFC – 400 psi inlet rating, 75 psi to 125 psi spring range, field set
- FSC – with cast iron “Y” type flanged strainer, fusion epoxy coated, inside and out (2-1/2” & 3” only)
- SC – sealed cage for use in pit or vault
- SW – made for salt water service
- HR – spring range is 75-125 psi, field set
- HLR – spring range is 10-125 psi, field set
- HTSTSC – high temperature application, up to 180° F
- LPV – high temperature application, up to 180° F, spring range is 10-35 psi, factory set at 20 psi
- BP – tapped and plugged for 3/4” bypass connection
- P – tapped and plugged for gauge
- G – tapped and plugged with gauge
- TBP – valve stem features integral thermal by-pass check valve (applies to 3″ size only)”
Accessories
- Repair kit (rubber only)
Dimensions & Weights (do not include pkg.)
SIZE
|
CONNECTIONS
|
DIMENSIONS (approximate)
|
WEIGHT
---|---|---|---
A
| B| C|
D
in.
|
mm
|
in.
| mm| in.| mm| in.| mm| in.| mm| lbs.|
kg.
2
|
50
|
FLANGED
|
10 3/8
| 263| 15| 381| 3| 76| 6 1/2| 165| 30|
13.5
2 1/2
|
65
|
FLANGED
|
10 3/8
| 263| 15| 381| 3 1/2| 89| 8| 203| 36|
16.5
3
|
80
|
FLANGED
| 11| 279| 17 3/4| 451| 3 3/4| 95| 8| 203| 50|
22.5
Flow Characteristics
MODEL 500XLFC 2″ THRU 3″ (STANDARD & METRIC)
Typical Installation
Local codes shall govern installation requirements. Unless otherwise specified, the assembly shall be mounted in accordance with the manufacturer’s instructions and the latest edition of the Uniform Plumbing Code. The assembly shall be installed with sufficient side clearance for testing and maintenance. The Model 500XLFC may be installed in any position. If installed in a pit or vault, or indoor application, specify the “SC” sealed cage option. Multiple installations are recommended for wide demand variations or where the desired pressure reduction is more than 4 to 1 (i.e.: 200 psi inlet reduced to 50 psi outlet).
CAUTION : Anytime a reducing valve is adjusted, a pressure gauge must be used downstream to verify correct pressure setting. Do not bottom adjustment bolt on bell housing.
Specifications
The Pressure Reducing Valve shall be certified to NSF/ANSI/CAN 61, consist of a bronze body and bell housing with flanged connections, shall have a separate access cover for the plunger and shall have a bolt to adjust the downstream pressure. The assembly shall be of the balanced piston design and shall reduce pressure in both flow and no-flow conditions. The bronze bell housing and access cap shall be threaded to the body and shall not require the use of ferrous screws. The Pressure Reducing Valve shall be a ZURN WILKINS Model 500XLFC.
Zurn Industries, LLC | Wilkins 1747 Commerce Way, Paso Robles, CA U.S.A.
93446 Ph. 855-663-9876, Fax
805-238-5766
In Canada | Zurn Industries Limited 7900 Goreway Drive, Unit 10,
Brampton, Ontario L6T 5W6, 877-892-5216
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>