RYOBI ROS310 Random Orbital Sander Instructions

June 9, 2024
RYOBI

RYOBI logo

Random Orbital Sander Instructions

RYOBI ROS310 Random Orbital Sander

ROS310

ROS310 Random Orbital Sander

Important!
It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.

Subject to technical modification
Safety, performance, and dependability have been given top priority in the design of your random orbital sander.

INTENDED USE

The random orbital sander is intended for sanding and finishing metal, wood, plastic, or similar materials using the abrasive pads provided. The random orbital sander is intended to be used by adult operators who have read the instruction manual and understand the risks and hazards. The random orbital sander should only be used in well ventilated areas. The random orbital sander is designed for dry sanding only.
The random orbital sander is intended for consumer use and should only be used as described above and not for any other purpose.

WARNING
Dust from certain paints, coatings, and other materials may cause irritation or allergic reactions. Dust from wood, such as oak, beech, MDF, and similar materials can be carcinogenic. Only qualified specialists should be allowed to use the product on materials containing asbestos.
WARNING
Do not use compressed air to remove dust from the product. Dirt and grit blown away by compressed air can cause serious eye injury.
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

SANDER SAFETY WARNINGS

  • Always wear safety goggles and a dust mask when sanding, especially when sanding overhead.
  • A suitable breathing respirator must be worn while sanding lead paint, some woods, and metal to avoid breathing the harmful/toxic dust or air.

RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise and the operator should pay special attention to avoid the following:

  • injury caused by dust
    NOTE: Using the product will produce considerable amount of dust and fine particles. Use the dust collection device or connect a dust extraction vacuum when operating the product. Wear dust masks containing filters appropriate to the materials being worked on. Ensure adequate workplace ventilation. Do not eat, drink, or smoke in the work area.

  • injury caused by noise and vibration
    NOTE: Wear ear protection during the sanding operation. Do not operate the product for long periods of time. See “Risk reduction”.

RISK REDUCTION
It has been reported that vibrations from handheld tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling,
numbness and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:

  • Keep your body warm in cold weather. When operating the unit wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
  • After each period of operation, exercise to increase blood circulation.
  • Take frequent work breaks. Limit the amount of exposure per day.

If you experience any of the symptoms of this condition, immediately discontinue use and see your doctor about these symptoms.

WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.

KNOW YOUR PRODUCT
See page 81.

  1. Power cord sleeve
  2. Speed control dial
  3. Live tool indicator
  4. On/off switch
  5. Sander cover
  6. Dustbox cover
  7. Dustbox container
  8. Sanding paper

MAINTENANCE

WARNING
The product should never be connected to a power supply when assembling parts, making adjustments, cleaning, performing maintenance, or when the product is not in use. Disconnecting the product will prevent accidental starting that could cause serious injury.
WARNING
When servicing, use only original Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.

GENERAL
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.

WARNING
Do not, at any time, let brake fl uids, gasoline, petroleum- based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic.
Electrical tools used on fi berglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure, because the fi berglass
chips and grindings are highly abrasive to bearings, brushes, commutators, etc. We do not recommend using the product for extended work on these types of materials.
WARNING
Always wear safety goggles or safety glasses with side shields during power tool operation. If operation is dusty, also wear a dust mask.
If the power supply cord is damaged, it must be replaced only by the manufacturer or by an authorised service centre to avoid risk. Contact authorised service centre.
For greater safety and reliability, all repairs should be performed by an Authorised Ryobi Service Centre.
LUBRICATION
All of the bearings in the product are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.

ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories, and packaging should be sorted for environmentfriendly recycling.

SYMBOLS ON THE PRODUCT

| Safety Alert
---|---
V| Volts
Hz| Hertz
**| Alternating current
W| Watts
no| No-load speed
min־¹| Revolutions or reciprocations per minute
Icon| Class II tool, double insulation
**
| CE Conformity
| EurAsian Conformity Mark
| Ukrainian mark of conformity
| Pad size
| Orbital diameter
| Please read the instructions carefully before starting the product.
| Wear ear protection.
| Wear eye protection.
| Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

SYMBOLS IN THE MANUAL

| Connect to the power supply.
---|---
| Disconnect from the power supply.
****| Note
| Speed, minimum
| Speed, maximum

The following signal words and meanings are intended to explain the levels of risk associated with this product:
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

RYOBI ROS310 Random Orbital Sander - Fig 1

RYOBI ROS310 Random Orbital Sander - Fig 2

RYOBI ROS310 Random Orbital Sander - Fig 3

RYOBI ROS310 Random Orbital Sander - Fig 4

RYOBI ROS310 Random Orbital Sander - Fig 5

Product specifications

Random Orbital Sander|
---|---
Model| ROS310
Rating| 310 W
Voltage| 220 V – 240 V
∼50/60 Hz
No-load speed| 7000 min־¹ –
13000 min־¹
Orbital stroke rate| 14000 – 26000 opm
Orbital diameter| 2.4 mm
Pad size| 125 mm
Weight According to EPTAProcedure 01/2003| 1.7 kg
Measured sound values determined according to EN 60745:|
A-weighted sound pressure level| LpA = 91,5 dB(A)
Uncertainty K| 3 dB
A-weighted sound power level| LWA = 102,5 dB(A)
Uncertainty K| 3 dB
Wear ear protectors.|
The vibration total values (triaxial vector sum) determined according to EN 60745:|
Vibration emission value| ah = 10 m/s2
Uncertainty K| 1,5 m/s2
Replacement part:|
Sanding pad| 5131030643

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

RYOBI® WARRANTY APPLICATION CONDITIONS

In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.

  1. The warranty period is 24 months for consumers and commences on the date the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.

  2. There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the  www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.

  3. The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages. The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply. This warranty does not apply to:
    – any damage to the product that is the result of improper or lack of maintenance
    – any product that has been altered or modified
    – any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
    – any damage caused by non-observance of the instruction manual
    – any product not displaying the CE approval mark on the rating plate
    – any product that has been attempted to be repaired by a nonauthorised warranty service centre or without prior authorisation by TechtronicIndustries
    – any product connected to improper power supply (amps, voltage, frequency)
    – any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
    – normal wear and tear spare parts
    – inappropriate use, overloading of the tool
    – use of non-approved accessories or parts
    – Power tool accessories provided with the tool or purchased separately, including but not limited to screw driver bits, drill bits, abrasive discs, sand paper and blades, lateral guide, etc.
    – Components (parts and accessories) subject to natural wear and tear, including but not limited to service & maintenance kits, carbon brushes, bearings, chuck, SDS drill bit attachment or reception, power cord, auxiliary handle, transport carry case, sanding plate, dust bag, dust exhaust tube, felt washers, impact wrench pins & springs, etc.

  4. For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.

  5. A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected

  6. This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.

AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit http://en.ryobitools.eu/header/service-and-support/service-agents

DECLARATION OF CONFORMITY
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Random Orbital Sander
Brand: Ryobi
Model number: ROS310
Serial number range: 46240601000001 – 46240601999999
is in conformity with the following European Directives and harmonised standards
2006/42/EC, 2014/30/EU, 2011/65/EU
EN55014-1:2006+A1:2009+A2:2011, EN55014-2:2015, EN61000-3-2:2014,
EN61000-3-3:2013, EN60745-1:2009+A11:2010, EN60745-2-4:2009+A11:2011
RoHS documentation is compiled according to EN 50581:2012

Andrew John Eyre (BEng, CEng, MIET)
Vice President, Regulatory & Safety
Winnenden, Jun. 23, 2017
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany

RYOBI logo

Techtronic Industries GmbH
Max-Eyth-Straße 10,
71364 Winnenden, Germany
20170717v1

RYOBI logo 2

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals