Perlick HP15 15 Inch Stainless Steel Refrigerator Instruction Manual

**Perlick HP15 15 Inch Stainless Steel Refrigerator Instruction Manual

**

TOOLS REQUIRED

• PPE (GLOVES AND SAFETY GOOGLES)
• PHILIPS SCREWDRIVER
• DRILL, AND 5/32’ DRILL BIT

DRILL OUT RIVETS

CAUTION: THESE CABINETS ARE EXTREMELY HEAVY. ENSURE THAT YOU HAVE ENOUGH PEOPLE ON HAND TO HELP REPOSITIONING THE UNIT SO IT CAN BE DONE SAFELY AND WITHOUT DAMAGE

UTILLIZING A DRILL WITH A 5/32” DRILL BIT, DRILL OUT TOP ROW OF RIVETS ALONG BACK OF THEBOTTOM CABINET.

LEG LEVELERS & GRILL REMOVAL

CAUTION: THESE CABINETS ARE EXTREMELY HEAVY. ENSURE THAT YOU HAVE ENOUGH PEOPLE ON HAND TO HELP REPOSITIONING THE UNIT SO IT CAN BE DONE SAFELY AND WITHOUT DAMAGE.

1. LAY UPPER CABINET ON ITS BACK AND REMOVE LEG LEVELERS FROM ALL CABINET SIZES.
2. UTILIZING A PHILLIPS HEAD SCREWDRIVER, REMOVE GRILL BY REMOVING THE TWO SCREWS THAT ARE LOCATED ON EACH SIDE OF GRILL (SEE PIC).

ATTACHING MOUNTING PLATE

STACKING UPPER UNIT ONTO LOWER UNIT

CAUTION: THESE CABINETS ARE EXTREMELY HEAVY. ENSURE THAT YOU HAVE ENOUGH PEOPLE ON HAND TO HELP REPOSITIONING THE UNIT SO IT CAN BE DONE SAFELY AND WITHOUT DAMAGE.

1. PLACE UPPER UNIT ON TOP OF LOWER UNIT. ALIGN FLANGE HOLES WITH THE RIVET HOLES PREVIOUSLY DRILLED.
2. UTILIZING A PHILIPS HEAD SCREWDRIVER, SECURE UPPER UNIT BY FASTENING #10 SCREWS PROVIDED IN KIT.

NOTE: TO PREVENT DAMAGE TO THE COMPRESSOR, WAIT 24 HOURS BEFORE POWERING ON UNIT AFTER TURNING THE CABINET BACK TO ITS UPRIGHT POSITION.

SCREWS REMOVAL

1. WITH A PHILLIPS HEAD SCREWDRIVER, REMOVE SCREWS (2X) FROM UNIT SIDE BRACKETS.
2. KEEP COMPONENTS (SCREWS) ASIDE FOR RE-ASSEMBLY LATER.

INSTALL MOUNTING BRACKET

1. ALIGN MOUNTING BRACKET TO HOLES (4X), 2 HOLES FROM WHERE OLD GRILL WAS SECURED TO (STEP 2), AND THE OTHER TWO HOLES ARE THE ONES FROM PREVIOUS STEP (STEP 5).
2. UTILIZING A PHILLIPS HEAD SCREWDRIVER, SECURE BRACKET BY UTILIZING TWO SCREWS FROM STEP 5, AND TWO SCREWS FROM STEP 6.

INSTALL FEMALE LATCHES TO BRACKET

CAREFULLY INSTALL FEMALE LATCHES (2X) INTO MOUNTING BRACKET ONE ON EACH SIDE BY PRESSING DOWN FIRMLY AGAINST SQUARE OPENING IN BRACKET. MAKE SURE FEMALE LATCHES ARE ALL WAY IN AND ORIENTED AS PICTURE BELOW (VERTICAL OPENING).

PREPARING GRILL (LATCH & BUMPERS)

1. NSTALL MALE LATCHES ON GRILL BY PRESSING FIRMLY AGAINST SQUARE OPENING ON EACH SIDE OF GRILL. MAKE SURE THE MALE LATCHES ARE FULLY ENGAGED AND ORIENTED VERTICALLY.
2. PEEL OFF THE PAPER OF EACH BUMPER PAD EXPOSING THE ADHESIVE SURFACE AND PLACE EACH ONE AS ORIENTED IN THE PICTURE BELOW.

INSTALL STACKING GRILL

1. PLACE AND ALIGN STACKING GRILL TO HOLES LOCATED RIGHT ABOVE FEMALE LATCHES ON EACH SIDE OF MOUNTING BRACKET.
2. UTILIZING A PHILLIPS HEAD SCREWDRIVER, SECURE STACKING GRILL WITH TWO #10 SCREWS PROVIDED IN KIT

FINAL STAGE

MAKE SURE TO WAIT 24 HOURS BEFORE POWERING ON UNIT AFTER TURNING THE CABINET BACK TO ITS UPRIGHT POSITION.

NOTE:
WHEN USING STACKING KIT TO JOIN (2) HH24 OR HA24 UNITS, A WALL MOUNT ANTI-TIP KIT MUST BE INSTALLED. SEE CABINET INSTALLATION MANUAL FOR INSTRUCTIONS.

3/3/2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>