MEAN WELL ELG-100 Series Constant Voltage + Constant Current LED Driver User Manual

70~100W Constant
Voltage + Constant
Current LED Dri ver
ELG-100 series
ser Manual

Features

• Constant Voltage + Constant Current mode output
• Metal housing design with functional Ground
• Built-in active PFC function
• Class 2 power unit
• No load / Standby power consumption <0.5W
• P67/1IP65 rating for indoor or outdoor installations
• Function options: output adjustable via potentiometer; 3 in 1 dimming (dim-to-off); Smart timer dimming; DALI
•  Typical lifetime>50000 hours
• 5 years warranty

Applications

• LED street lighting
• LED architectural lighting
• LED bay lighting
• LED floodlighting
• Type “HL” for use in Class I, Division 2 hazardous (Classified) location.

GTIN CODE
MW Search: https://www.meanwell.comserviceGTIN.aspx

Description

ELG-100 series is a 100W AC/DC LED driver featuring the dual mode constant voltage and constant current output. ELG-100 operates from 100~360VAC and offers models with different rated voltage ranging between 24V and 54V. Thanks to the high efficiency up to 91%, with the fanless design, the entire series is able to operate for -40’C ~ +90°C case temperature under free air convection. The design of metal housing and IP67/IP65 ingress protection level allows this series to fit both indoor and outdoor applications. ELG-100 is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for LED lighting system
Model Encoding

Stock
AB| IP65| lo and Vo adjustable through built-in potentiometer & 3 in 1 dimming function (0-10Vdc, 10V PWM signal and resistance)| In Stock
DA| IP67| DALI control technology.| In Stock
Dx| IP67| Built-in Smart timer dimming function by user request.| By request
D2| IP67| Built-in Smart timer dimming and programmable function.| In Stock

SPECIFICATION

MODEL| ELG-100-24| ELG-100-36| ELG-100-42| ELG-100-48| ELG-100-54
---|---|---|---|---|---
OUTPUT| DC VOLTAGE| 24V| 36V| 42V| 48V| 54V
CONSTANT CURRENT REGION Note.2| 12 ~ 24V| 18 ~ 36V| 21 ~ 42V| 24 ~ 48V| 27 ~ 54V
RATED CURRENT| 4.0A| 2.66A| 2.28A| 2A| 1.78A
RATED POWER| 200VAC ~ 305VAC
96W| 95.76W| 95.76W| 96W| 96.12W
100VAC ~ 180VAC
70W| 70W| 70W| 70W| 70W
RIPPLE & NOISE (max.) Note.3| 200mVp-p| 250mVp-p| 250mVp-p| 300mVp-p| 350mVp-p
VOLTAGE ADJ. RANGE| Adjustable for A/AB-Type only (via the built-in potentiometer)
21.6 ~ 26.4V| 32.4 ~ 39.6V| 37.8 ~ 46.2V| 43.2 ~ 52.8V| 48.6 ~ 59.4V
CURRENT ADJ. RANGE| Adjustable for A/AB-Type only (via the built-in potentiometer)
2 ~ 4A| 1.33 ~ 2.66A| 1.14 ~ 2.28A| 1 ~ 2A| 0.89 ~ 1.78A
VOLTAGE TOLERANCE Note.4| ±3.0%| ±2.5%| ±2.5%| ±2.0%| ±2.0%
LINE REGULATION| ±0.5%| ±0.5%| ±0.5%| ±0.5%| ±0.5%
LOAD REGULATION| ±1.0%| ±1.0%| ±0.5%| ±0.5%| ±0.5%
SETUP, RISE TIME Note.6| 1000ms, 80ms/115VAC 500ms, 100ms/230VAC
HOLD UP TIME (Typ.)| 15ms/115VAC  10ms/230VAC
INPUT| VOLTAGE RANGE  Note.5| 100 ~ 305VAC  142 ~ 431VDC continue,320VAC for 24Hrs; 360VAC for 1Hr
(Please refer to “STATIC CHARACTERISTIC” section)
FREQUENCY RANGE| 47 ~ 63Hz
POWER FACTOR| PF≧0.97/115VAC, PF≧0.95/230VAC, PF≧0.92/277VAC@full load
(Please refer to “POWER FACTOR (PF) CHARACTERISTIC” section)
TOTAL HARMONIC DISTORTION| THD< 20%(@load¾50%/115VC; @load¾60%/230VAC; @load¾75%/277VAC) (Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
EFFICIENCY (Type.)| 88%| 89%| 90%| 90%| 91%
AC CURRENT| 1.1A / 115VAC       0.6A / 230VAC      0.5A/277VAC
INRUSH CURRENT(Typ.)| COLD START 60A(twidth=850μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER| 3 units (circuit breaker of type B) / 6 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT| <0.75mA / 277VAC
NO LOAD / STANDBY POWER CONSUMPTION| No load power consumption <0.5W for Blank / A / Dx / D2-Type Standby power consumption <0.5W for B / AB / DA-Type
PROTECTION| OVER CURRENT| 95 ~ 108%
Constant current limiting, recovers automatically after fault condition is removed
SHORT CIRCUIT| Hiccup mode, recovers automatically after fault condition is removed
OVER VOLTAGE| 28 ~ 34V| 41 ~ 48V| 47 ~ 54V| 54 ~ 62V| 62 ~ 72V
Shut down output voltage, re-power on to recover
OVER TEMPERATURE| Shut down output voltage, re-power on to recover
ENVIRONMENT| WORKING TEMP.| Tcase=-40 ~ +90℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
MAX. CASE TEMP.| Tcase=+90℃
WORKING HUMIDITY| 20 ~ 95% RH non-condensing
STORAGE TEMP., HUMIDITY| -40 ~ +80℃, 10 ~ 95% RH
TEMP. COEFFICIENT| ±0.03%/℃ (0 ~ 60℃)
VIBRATION| 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
SAFETY & EMC| SAFETY STANDARDS| UL8750(type”HL”), CSA C22.2 No. 250.13-12; IEC/BS EN/EN/AS/NZS 61347-1, IEC/BS EN/EN/AS/NZS 61347-2-13 independent, BS EN/EN62384; EAC TP TC 004;BIS IS15885(for 24/24A/24B/24DA/36/36A/36B/42/42A/42ADA/42B/48/48B/54/54A/54ADA/54B only); GB19510.1, GB19510.14; IP65 or IP67;KC61347-1,KC61347-2-13 approved
DALI STANDARDS| Compliance to IEC62386-101,102,(207 by request) for DA Type only
WITHSTAND VOLTAGE| I/P-O/P:3.75KVAC  I/P-FG:2.0KVAC  O/P-FG:1.5KVAC
ISOLATION RESISTANCE| I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION| Compliance to BS EN/EN55015,BS EN/EN61000-3-2 Class C (@load≧60%); BS EN/EN61000-3-3;GB/T 17743, GB17625.1; EAC TP TC 020; KC KN15,KN61547
EMC IMMUNITY| Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11; BS EN/EN61547, light industry level (surge immunity Line-Earth 6KV, Line-Line 4KV); EAC TP TC 020; KC  KN15,KN61547
OTHERS| MTBF| 2920.8K hrs min. Telcordia SR-332 (Bellcore) 282.9Khrs min. MIL-HDBK-217F (25℃)
DIMENSION| 1996335.5mm (LWH)
PACKING| 0.85kg; 16pcs/14.2kg/0.72CUFT
NOTE| 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25℃ of ambient temperature.
2. Please refer to “DRIVING METHODS OF LED MODULE”. For DA-Type, Constant Current region is 60%~100% of maximum voltage under rated power delivery.
3. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
4. Tolerance : includes set up tolerance, line regulation and load regulation.
5. De-rating may be needed under low input voltages. Please refer to “STATIC CHARACTERISTIC” sections for details.
6. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
7. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf)
8. This series meets the typical life expectancy of >50,000 hours of operation when Tcase, particularly tc point (or TMP, per DLC), is about 80℃ or less.
9. Please refer to the warranty statement on MEAN WELL’s website at http://www.meanwell.com
10.  The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
11.  For any application note and IP water proof function installation caution, please refer our user manual before using. https://www.meanwell.com/Upload/PDF/LED_EN.pdf
12.  D2 models need to be programmed in the state of loading.
13. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.
Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx  File Name:ELG-100-SPEC 2024-01-08

Block Diagram

DRIVING METHODS OF LED MODULE
This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
This characteristic applies to Blank/A/B/AB/DX/D2-Type, For DA-Type, the Constant Current area is 60%~100% Vo.

DIMMING OPERATION

※ 3 in 1 dimming function (for B/AB-Type)

• Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIN-:
  0~10VDC, or 10V PWM signal or resistance.

• Direct connecting to LEDs is suggested. Itis not suitable to be used with additional drivers.

• Dimming source current from power supply: 100pA (type.)
  Applying additive 0~ 10VDC

• DIM# for BIAB-Type PROG: tr 0 Tpe
  *”DIM- or BIAB-Type Difor DA-Type PROG-forD2-Type

※ DALI Interface (primary side; for DA-Type)

• Apply DALIsignal between DA+ and DA-.
• DALI protocol comprises 16 groups and 64 addresses.
• Firststeps fixed at 8% of output.

※ Smart timer dimming function (for Dxx-Type by User definition)
MEAN WELL Smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level to perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. If other options may be needed, please contact MEAN WELL for details.
Ex: D01-Type: the profile recommended for residential lighting

Set up for DO1-Type in Smart timer dimming software program:

| T1| T2| T3
---|---|---|---
TIME| 01:30| 11:00| —
LEVEL| 70%| 100%| 70%

** TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level.
Example: If aresidential lighting application adopts D01-Type, when turning on the power supply at 6:00pm, for instance:

1. The power supply will switch to the constant current level at 100% starting from 6:00pm.
2. The power supply wil switch to the constant current level at 70% turn, starting from 0:00am, which is 06:00 after the power supply turns on.
3. The power supply will switch to the constant current level at 50% in turn, starting from 1:00am, which s 07:00 after the power supply turns on.
4. The power supply will switch tothe constant current level at 70% in tun, starting from 5:00am, which is 11:00 after the power supply turns on.
   The constant current level remains till 8:00am, which is 14:00 after the power supply tums on.

Ex: D02-Type: the profile recommended for street lighting Set up for D02-Type in Smart timer dimming software program:

| T1| T2| T3| T4| T5
---|---|---|---|---|---
TIME| 01:00| 03:00| 8:00| 11:00| —
LEVEL| 50%| 80%| 100%| 60%| 80%

** TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level.
Example: Ifa street lighting application adopts D02-Type, when turning on the power supply at 5:00pm, for instance:

1. The power supply will switch to the constant current level at 50% starting from 5:00pm.
2. The power supply will switch to the constant current level at 80% in turn, starting from 6:00pm, which s 01:00 after the power supply turns on.
3. The power supply will switch to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the power supply turns on.
4. The power supply will switch to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the power supply turns on.
5. The power supply will switch to the constant current level at 80% in tur, starting from 4:00am, which s 11:00 after the power supply turns on. The constant current level remains till 6:30am, which s 14:00 after the power supply turns on.

Ex: D03-Type: the profile recommended for tunnel lighting Set up for D03-Type in Smart timer dimming software program:

| T1| T2| T3
---|---|---|---
TIME| 01:30| 11:00| —
LEVEL| 70%| 100%| 70%

** TIME matches Operating Time in the diagram whereas LEVEL matches Dimming Level.
Example: Ifa tunnel lighting application adopts DO3-Type, when turning on the power supply at 4:30pm, for instance:

1. The power supply will switch to the constant current level at 70% starting from 4:30pm.
2. The power supply will switch to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the power supply turns on.
3. The power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the power supply turns on.
   The constant current level remains tll 8:30 am, which s 14:00 after the power supply turns on.

OUTPUT LOAD vs TEMPERATURE (Note.9)

STATIC CHARACTERISTIC ※ De-rating is needed under low input voltage.
POWER FACTOR (PF) CHARACTERISTIC
※ Tease at80°C
Constant Current Mode

TOTALHARMONIC DISTORTION (THD)
※ 54V Model, Tcase at80°C

EFFICIENCY vs LOAD
ELG-100 series possess superior working efficiency that up to 91% can be reached in field applications.
※ 54V Model, Tease at 80°C

LIFE TIME

Mechanical Specification

※ Blank-Type
CASENO :244A Unitmm ※ AB-Type※ BIDAID2-Type

※ Model (3-wire input)

Recommend Mounting Direction

INSTALLATION MANUAL
Please refer to: http://www.meanwell.com/manual.htm!

http://www.meanwell.com.cn/Upload/PDF/LED_EN.pdf
Downloaded from Arrow.com .
File Name:ELG-100-SPEC 2024-01-08

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>