sanagS3S OWS Bluetooth Headset User Guide

: June 1, 2024
: sanag

Table of Contents

Product Overview
- Key Function Operation
Bluetooth Operation

sanagS3S OWS Bluetooth Headset

Product Overview

Key Function Operation

Power on: Turn on automatically after opening the charging compartment and taking out the headset, the ice blue light flashes quickly, and long press the MFB key for 3S to start manually.
Shutdown:
1. Put the headset into the charging compartment and automatically shut down.
The ice blue light flashes for 3 times and then turns off.
2. Press and hold the MFB button for about 7 seconds to tum off the ice blue Aughts Blink for 3 times quickly and then warn off.
3. The headset automatically shuts down when the low power reaches 3.0V, and the ice blue light flashes for 3 times quickly and then turns off.
Pairing: The 1WS pairing state is automatically entered after the startup, and the ice blue lights on the left and right ears flash slowly.
Answer: When a call comes in, dick the MFB key of the left and right ears.
Hang up: During the call, double-click the MFB button of the left and right ears.
Reject: When an incoming call comes, press the MFB key of the left and right ears for 2 seconds.
Play/Pause: Olick the MFB key of the left and right ears.
Previous: Double dick MFB batten on left ear.
Next Double dick MFB button on right ear.
Volume plus: Hit left ear MFB key three times.
Volume reduction: hit MFB key of right ear three times.
Voice Assistant: Press and hold the ear MFB key for about 3 seconds to release the voice assistant and dick to exit.
Reset headset: When the phone is not connected, press the MFB button of the left and right ears at any time to reset the headset factory Settings, and the ice blue light will turn on for 2 seconds after successful reset.
Game Mode/Music mode: Hit the MFB button of the left and right ears 4 times to enter the low latency mode, and then switch to the music mode 4 times.
Low power alarm: When the headset battery is insufficient, it will prompt a low power Alan tone every 3 minutes.
Charging: Put the earphones into the charging cabin and dose the cover. The cabin charges the earphones. The ice blue light will turn on long. Charging cabin charge, charging cabin ice blue lights continue to flash slowly, full of Ice blue lights long light

Bluetooth Operation

Bluetooth connection is successful:

The headset enters Bluetooth mode, and the phone searches for the
Bluetooth pairing name “sang S3S /sang S3S Al “. Click on the connection,
The headset is connected to the device once by default. The ice blue indicator blinks slowly and the headset indicator is off.

Bluetooth disconnected:

1. Manually turn off the Bluetooth of the mobile phone, and the headset enters Bluetooth pairing mode.
2. Disconnect the headset from the mobile phone after over distance, return to the effective distance range, can connect the mobile phone normally, more than 5 minutes will automatically shut down.
Bluetooth Operation

Specifications

Name: OWS Bluetooth headset
Model: sanag S3S /sanag S3S Al
Bluetooth version: V 5.3
Connection range: .?10m
Charging voltage: 5V= 1A
Headphone battery capacity: 40mAh
Battery capacity: 400mAh

Matters needing attention

Do not use abrasive cleaners to clean this product.
Do not allow this product to be heated or close to a fire source, such as a cooking stove.
Do not expose the product to direct sunlight for a long time.
Do not discard this product in fire to avoid explosion.
Do not attempt to disassemble this product to make any modifications, as it does not contain any maintenance components.
Do not use this product In rain.
If you do not plan to use this product for a long time, please store it in a dry environment and charge the headset at least once a month to extend its life and avoid extreme temperatures and dust.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, induding interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radian technician for help.

The device has been evaluated to meet general RF exposure requirement.