AURA INDIGO-4.80 4 Channel Stereo Power Amplifier User Manual

June 1, 2024
Aura

AURA INDIGO-4.80 4 Channel Stereo Power Amplifier User Manual
AURA INDIGO-4.80 4 Channel Stereo Power Amplifier

Congratulations and thank you for purchasing AurA INDIGO series amplifiers, the logical choice in mobile audio amplification. Your amplifiers have been designed and engineered with the highest quality components and top of the line workmanship to help you reach the superior sound you are after.
To achieve optimal performance of your system, please take a few moments to read over this Owner’s manual or visit authorised dealer if needed before starting your installation.

FEATURES

  • STABLE INTO 2 OHM LOAD
  • HIGH SPEED SAMOSET POWER SUPPLY
  • EFFECTIVE PROTECTION
  • HI-LEVEL INPUT
  • BASS BOOST
  • 12dB/OCT VARIABLE LOW PASS FILTER
  • 12dB/OCT VARIABLE HIGH PASS FILTER
  • REMOTE CONTROL (OPTIONAL)

SPECIFICATIONS

RMS power (4 Ohm): 80w x 4
RMS power (2 Ohm): 120w x 4
RMS power (4 Ohm) bridged: 250w x 1 (3/4 channel bridged)
Working Impedance: 2/4
Input Sensitivity: 8V-0.2 V
Low Pass Filter (3/4 channel): 50 Hz-250 Hz
Hi Pass Filter : 60 Hz-6 kHz
Frequency Response: 10 Hz-30 kHz
Signal to Noise Ratio : >90 dB
THD : < 0.1%
Working voltage: 9V-16V
Dimensions (mm): 320 x 190 x 54

All features are subject to change in the continuing effort to improve the products without notice.

POWER CONNECTION

Power Connection
BATT (12V POWER)
Before mounting amplifiers, disconnect the negative cable from the battery to protect any accidental damage to your amplifiers and audio system.
Connect the power cable to power terminal +12V.
All AurA INDIGO series amplifiers are equipped with fuses, but external fuses also should be used.
Connect one end of fuse holder to the power cable going into the amplifiers and the other end of fuse holder to positive battery. This fuse location will protect the system and the vehicle against the possibility of a short circuit in the power cable.
Be sure to use fuses and fuse holder adequate for the application.

GND (GROUND)
Locate a secure grounding connection as close to amplifier as possible. Make sure the location is clean and provides a direct electrical connection to the frame of the vehicle. The ground needs to have as low of a resistance as possible. Connect one end of a short piece of the same size cable as the power cable to the grounding point or to one of your batteries or battery bank. Run the other end of the ground cable to the mounting location of the amplifiers for connection to the amplifiers ground terminals and connect the ground cable to the GND (ground terminal).

REM (REMOTE)
Run a remote turn on cable from the switched 12V source. This may be a toggle switch, a relay, your source unit’s remote trigger cables, or power antenna trigger cable. Connect the remote turn on cable to the REM (remote) terminal.

RCA INPUT CONNECTION

Connection

SPEAKER CONNECTION

Connection
Connection

TROUBLE SHOOTING

  • AurA INDIGO series amplifiers have protection features to prevent any damages from misuse or faulty conditions.
  • If INDIGO series amplifiers sense excessive heat, short circuited speakers DC, or voltage the protection indicator will light, and the system will be turned off.
  • In order to check the problem, you should turn all levels down and all power off and careful check the installation for wiring mistakes or short.
  • If AurA INDIGO series amplifiers shuts down due to excessive heat, they will be working later when it is cooled down.
  • Before removing your amplifier, refer to the list below and follow the suggested procedures.

NO SOUND (NO OUTPUT)

  • Please check all connections, cables routing, short & voltage.
  • Please check the fuses. If they are blown, please replace with new one.
  • Please check whether speakers work well, you can test speakers by connecting to another amplifier

DISTORTION & NOISE

  • Readjust input level and check the speaker quality at another amplifier. Replace poor quality speakers with good quality ones.
  • Check amplifiers and head unit’s ground contact. All grounds should be common.
  • Check RCA cable, then replace with new one or reroute RCA cable.
  • Engine noise is caused by poor grounding of amplifiers, head unit, other components, battery or alternator, so please check all grounding connection.

POOR BASS RESPONSE
Please check speaker cables and reverse polarity.
Company logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals