NATIVE UNION DROP03 Drop Wireless Charger Instruction Manual
- June 17, 2024
- NATIVE UNION
Table of Contents
NATIVE UNION DROP03 Drop Wireless Charger
HOW TO CONNECT
ALIGNMENT
AirPods Charging
Make sure the AirPods or AirPods Pro are placed on the center of the charging area. The white status LED may blink or switch off repeatedly while charging – this does not affect the charging progress. AirPods Pro charging status can be checked by tapping on the case. If the LED blinks orange, charging is still orange. If the LED blinks green, charging is complete. A full charge takes 3-5 hours.
NOTES
LED INDICATION
- White light: Red light flashing
- Charging: Foreign object detected e.g. metallic object
SPECIFICATION
- Input: DC5V,2.0A DC9V,1.67A DC12V, 1.5A
- Frequency: 127.7 kHz
- Output Power: 5W/7.5W/10W
- Charging distance: ≤3mm
SAFETY INFORMATION
- This product is intended for home & office use
- For indoor use only
- Consult local staff before using the product near medical or industrial equipment or on board an aircraft
- Prevent cables from being pinched or damaged
- A damaged cable or device may malfunction and / or overheat (Fire hazard)
- Unplug the product if not used for an extended period of time
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC ID: X3QDROP03
RSS STATEMENT
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. IC: 23711-DROP03
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the
percentage cor percentage value of presence condition.
Note 2: “O” indicates that the percentage content of the restricted
substance does not extent of the restricted substance exceeds the reference
exceed the percentage of the reference value of presence.
Note 3: The “-” indicates that the restricted substance corresponds to
the exemption.
More information
- nativeunion.com/product-documentation
- nativeunion.com/support
- Insta: nativeunion
- Fb: nativeunion
- Twitter: native_union
- nativeunion.com
IN THE BOX
- Drop Qi Charger,
- Cable (2m USB-A – USB-C),
- Manuals
SPECIFICATION
- Input: 5V/2A, 9V/1.67A, 12V/1.5A;
- Output: Frequency 127.7kHz; Power 5W/7.5W/10W;
- Charging Distance: ≤ 3mm
SET- UP AND USAGE
SET- UP
- Connect cable to Drop and USB charger (not-included).
- Recommended USB charger: 5V/2A (USB-A) for 5W Qi; 9V/1.67A or 12V/1.5A (USB-A QC 3.0 or USB-C PD) for ≤ 10W Qi.
USAGE
Assure careful alignment of the charging coils (center to center). White LED shows device is charging. If LED turns off or flashes red, check the device alignment. If problem persists remove phone case and accessories. Never place metal objects on the charger. AirPods Charging: Make sure the AirPods or AirPods Pro are placed on the center of the charging area. The white status LED may blink or switch off repeatedly while charging – this does not affect the charging progress. A full charge takes 3-5 hours.
SAFETY INFORMATION
- This product is intended for home & office use.
- For indoor use only.
- Consult local staff before using the product near medical or industrial equipment or on board an aircraft.
- Prevent cables from being pinched or damaged.
- A damaged cable or device may malfunction and/or overheat. (Fire hazard)
- Unplug the product if not used for an extended period of time.
EU DECLARATION OF CONFORMITY
- Hereby, Design Pool Limited declares that the product DROP03/DROPLTO1 is in compliance with directive 2014/53/EU. The full text of the EU DoC is available online: nativeunion.com/product-compliance
- Manufacturer: Design Pool Limited. 2/F East Town Building, 41 Lockhart Road, Wan Chai, Hong Kong – support@nativeunion.com
Made in China
© 2020 Native Union all rights reserved. Native Union is a registered trademark of Design Pool Limited. Trademarks and trade names are those of their respective owners. Copyright Design Pool Limited.
Scan
- nativeunion.com/support
- USA: +1 (855) 969 5525
- Canada: +1 855-969-2677
- Europe: +44 800 802 1495
- UK: +44 800 802 1495
- Australia/NZ: +61 1800 531 729
- APAC: +852 3590 5275
© Copyright Native Union 2020
© 2020 Native Union all rights reserved. Native Union is a registered trademark of Design Pool Limited. Trademarks and trade names are those of their respective owners. Copyright Design Pool Limited. 2/F, East Town Building, 41 Lockhart Road, Wan Chai, Hong Kong. Made in China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>