brondell Swash 800 High Tech Toilet Seat Owner’s Manual
- June 17, 2024
- brondell
Table of Contents
brondell Swash 800 High Tech Toilet Seat
Important Safeguards
For safety reasons. olease read this entire manual before use.
Specifications
Parts & Configuration
Before Installation
Tools Needed
- Flat head screwdriver
- Univeral Wrench (included)
- Phillips screwdriver
- Measuring tape
NOTE: The included Universal Wrench will work for most applications. Depending on your toilet configuration, an adjustable wrench may also be needed.
Alternate Mounting Hardware
Some toilets may not provide adequate access to the seat mounting holes
preventing proper installation
of the Standard Mounting Hardware.
In this case, you will need to use the Alternate Mounting Hardware and follow
the enclosed instructions.
Check Water Supply Line
Check the line that connects the toilet tank to the water shut off valve. If it is a rigid pipe, you may need to purchase a flexible hose to replace it before installing the Swash. The length of the hose and the size of the connectors will vary.
Installation
CAUTION
Please read these instructions carefully before installing the Swash 700 / 800 Failure to do so could result in flooding, leaking, or damage to the product.
Remove Toilet Seat
- a) Lift hinge covers and use a screwdriver to remove the mounting bolts.
- b) Remove the toilet seat.
Steps may vary by type of seat.
Turn Water Off and Flush Toilet
You may wish to place a container under the tank to catch any leaking that could occur during installation.
- a) Turn water valve off completely.
- b) Flush the toilet to empty the tank.
- c) Disconnect water supply line from toilet tank.
IMPORTANT: Do not continue without completing these steps! Failure to do so could result in flooding, leaking, or damage to the product.
Install Mounting Plate
NOTE: These instructions are for Standard Mounting Hardware. See page 2 for further details on Alternate Mounting Hardware.
-
a) Place Mounting Plate over mounting holes, flat side down, curve toward the back of toilet.
-
b) Insert bolts through the Mounting Plate and loosely tighten the wingnuts. Make sure the crush washer and metal flat washer are put on in the correct order (see graphic).
-
c) Adjust mounting plate so length (L) between the front of the toilet bowl and the back of the mounting plate is as follows:
(S700 / S800 – RW & RB) L = 18 1/4″ (465 mm)
(S700 / S800 – EW & EB) L = 20 1/2″ (495 mm) -
d) Tighten Mounting Bolts with a screwdriver until the mounting plate is securely fastened to the toilet.
Connect T-Valve and Hoses
If your water supply line is rigid, you may need to replace it before
continuing. See page 2 for further details.
- a) Install the T-Valve between the water supply line & the toilet tank.
- b) Place the Swash on or beside the toilet and connect the Bidet Hose to the Swash.
IMPORTANT! Use the wrench to tighten all connections before continuing. Failure to do so could result in flooding, leaking, or damage to the product.
Attach the Swash 700 / 800
Slide the Swash onto the mounting plate.
You will hear a “click” indicating the seat has been properly attached. To
release the Swash: push the button located on the right hand corner of the
seat and gently pull.
Turn On Water and Connect Power
- a) Turn the water valve back on slowly. Ensure the connections are not leaking before continuing.
- b) Make sure hands are dry. Insert the power plug into a grounded GFCI outlet. The blue power LED will illuminate.
Battery Installation
Load two (2) AAA batteries (included) into Remote Control as shown. Tighten battery cover with screw.
Remote Control Installation
identity a location for the Remote Control that is visible and reachable from
the toilet and that does not obstruct the IR signal coming from the top of the
remote. Depending on your wall type, you can install the screws directly or
use the anchor mounts as shown.
If you prefer to not drill holes into your wall, you may use double sided foam
tape to adhere bracket to the wall. In this case, make sure to choose a tape
with an adhesive that will not damage wall upon removal.
Filling the Reservoir
Sit on the Swash to activate the seat switch. Press one of the wash functions
on the remote control.
The reservoir will begin to fill. It will take between 10 to 20 seconds for
the reservoir to fill completely.
When the reservoir is full, the wash wand will extend and begin to spray. Push
STOP to cancel the wash function.
Your Swash is now ready for use!
Troubleshooting
Operation
Some features of the Swash 700 / 800 are designed to function only when seat is occupied.
Using the Swash 700 / 800
Warm Water Washing:
Sit on the seat and press the FRONT or BACK (either HIM or HER) button to
begin water flow. Press the STOP button to discontinue the water flow.
Water Flow/Pressure Adjustment:
Press the + button to increase pressure or the – button to decrease
pressure. Repeat until the desired pressure is reached. There are five levels
of water pressure. Each wider bar on the LCD display represents a level
increase.
Pulsating Water Mode: (water pressure level must be at 3 or above)
To change to pulsating mode, press and hold the FRONT or BACK button for over
3 seconds.
To deactivate and return to normal washing mode, repeat the above step.
Warm Air Dryer: (available in Swash 800)
Press the WARM AIR button to start the dryer. Press STOP to stop the dryer.
Adjusting Seat, Water, and Dryer Temperature
Adjusting Seat Temperature
Press SEAT TEMP button to adjust temperature. Repeat until desired level is achieved. There are four temperature levels: low> medium>high>off No LCD graphic indicates seat heating is off. Each wider bar on the LCD display represents one level increase.
Adjusting Water Temperature
Press WATER TEMP button to adjust temperature. Repeat until desired level is achieved. There are four temperature levels: low>medium>high>off No LCD graphic indicates seat heating is off. Each wider bar on the LCD display represents one level increase.
Adjusting Warm Air Dryer Temperature (available in Swash 800)
Press WARM AIR button to adjust temperature. Repeat until desired level is
achieved. There are three temperature levels: low>medium>high Each wider bar
on the LCD display represents one level increase.
NOTE: Temperature settings are stored in memory according to last settings.
Setting the Clock
Press and hold the STOP button on the Remote Control for over 5 seconds until
the Clock flashes.
Use the @ button to set the Hour and the button to set the Minutes.
When finished, press the STOP button or simply do not press any buttons for 10
seconds.
Power Save Mode
The Swash 700 / 800 includes a power saving feature to reduce electrical
consumption when not in use.
Once set, the Powersave function turns the Swash on and off each day according
to your time settings.
Setting Powersave Start and End Times
- a) Press the Powersave button on the remote control for 5 seconds. “POWERSAVE START” on the remote and the Powersave LED on the Swash will flash.
- b) Set the Powersave start time using © WATER FLOW for hours and * WATER FLOW for minutes. When the desired start time is displayed, press the Powersave button.
- c) “POWERSAVE END” on the remote and the Powersave LED on the Swash will flash. Set the Powersave end time using © WATER FLOW for hours and WATER FLOW for minutes. When the desired end time is displayed, press the Powersave button. The remote LCD will show POWERSAVE and the Powersave LED on the seat will be green. Powersave is now armed and the unit will go into power save mode at the specified start time.
Enabling and Disabling Powersave
- a) Press POWERSAVE to toggle between Powersave enabled and Powersave disabled.
- b) To change Powersave Start and End times, hold POWERSAVE for 5 seconds and repeat procedure above.
When Powersave is Operating
- a) When the Swash is in Powersave mode, the associated LED on the seat will glow Orange
- b) Sitting on the Swash while it is in Powersave mode will return the unit to normal operation.
- c) The Swash will not re-enter Powersave mode until the next day’s scheduled start time
Auxiliary Controls
There are two buttons on the rear, right corner of the Swash 700 / 800 for use when the Remote Control is unavailable.
- Rear Wash: Sit on the seat and press the AUX WASH button to begin water flow (only posterior cleaning is available when using Auxiliary Controls).
- Water Pressure: Press again the AUX WASH button until desired water pressure is achieved. Press the AUX STOP button to discontinue the water flow.
- Warm Air Dryer (available in Swash 800): Press the AUX STOP button to activate Warm Air Dryer. It will automatically be set to the medium temperature level. Press AUX STOP to turn off the Dryer.
- Seat Temperature: To adjust Seat Temperature, press and hold the AUX STOP button for more than 5 seconds. Press AUX STOP button again to change seat temperature: Low>Medium>High>Off
- Water Temperature: To adjust Water Temperature, press and hold the AUX WASH button for more than 5 seconds. Press AUX WASH button again to adjust water temperature: Low>Medium>High>Off
Remote Control Beeping/Silent Modes
The Remote Control has two modes: Beeping Mode and Silent Mode. Beeping Mode beeps to confim when a command from the remote has successfully been received by the seat. To change modes press and hold the WATER TEMP button for 5 seconds.
Maintenance
Always unplug the Swash before cleaning.
Seat Cleaning and Removal
Use a soft, damp cloth and mild cleanser (such as dish soap) to wipe down the
seat. DO NOT scrub or use harsh, abrasive products to clean the Swash.
For a more thorough cleaning, you may remove the
Swash. lo release, push the button located on the back right side of the seat
and pull forward.
Nozzle Cleaning
It is recommended that you clean the retractable nozzles monthly or as
necessary. To clean the nozzles, pull them out gently and use a soft, damp
brush or cloth to wipe down. DO NOT use soap or detergents to clean the
nozzles.
Filter Cleaning
For proper Swash 700 / 800 function, it is important to occasionally clean the
filters. Frequency of cleaning depends on your local water supply. Clogged
filters cause decreased water flow, affecting operation.
For other issues or questions, contact Brondell Customer Service: 1-888-542-3355
Contact Information
Brondell Inc. PO Box 470085
San Francisco, CA 94147-0085
Phone: 1-888-542-3355
E-mail: support@brondell.com
WEB: www.brondell.com
Warranty
Please refer to the Warranty Card enclosed with the purchase of the Swash, or
go on-line at www.brondell.com for warranty detail.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>