brondell BR60-RW Breeza Warm Luxury Heated Toilet Seat Owner’s Manual

BR60-RW Breeza Warm Luxury Heated Toilet Seat

Important Safeguards

GROUNDING lNSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into a 120V GFCI outlet that is properly installed and grounded. DANGER – Improper use of the grounding plug can result in the risk of electric shock. If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded. If it is necessary to use an extension cord, use only a three wire extension cord that has a three-blade grounding plug, and a three- slot receptacle that will accept the plug on the product. Replace or repair a damaged cord.

Important Safeguards

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING  DANGER -To reduce the risk of electrocution:

1. Do not use while bathing.
2. Do not place or store product where it can fall or be pulled into a tub or tank.
3. Do not place in or drop into water or other liquid.
4. Do not reach for a product that has fallen into water. Unplug immediately.

WARNING -To reduce the risk of burns, electrocution, fire, or injury to persons:

1. Close supervision is necessary when this product is used by, on, or near children or invalids.
2. Use this product only for its intended use as described in the owner’s manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
6. Never use while sleepy, drowsy, intoxicated, or under the influence of medication that may affect your judgement.
7. Never drop or insert any object into any opening or hose.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Connect this product to a properly grounded GFCI outlet only. See Grounding Instructions.

Important Safeguard

• Danger – Possibility of Electric Shock! Use the correct voltage according to the Specifications and connect to a three prong GFCI grounded outlet.
• Please use caution not to spray water directly on the BREEZA WARM This could cause serious damage to the product, and may result in electric shock or fire.
• Do not use harsh brushes or abrasive detergents to clean the BREEZA WARM. Use only mild soap and a soft cloth for cleaning.
• Do not disassemble or modify he BREEZA WARM. Only an authorized service representative should nertorm repairs.

Specifications

Parts List

Before Installation

Items required but NOT included: Screwdriver, wrench.
Be sure that all parts are on hand before proceeding with the installation.
Under normal circumstances, tools are not required for the installation process. However, some toilet bowls may be designed with hard to reach areas, in which case, a screwdriver and wrench may be required.

Installation

Please read these instructions carefully before installing the BREEZA WARM. Failure to do so may result in damage to the product.

Removing Existing Toilet Seat

• a) Lift hinge covers and use a screwdriver to remove the mounting bolts.
• b) Remove the toilet seat.Steps may vary by type of seat.

Installing the BREEZA WARM

• a) Insert the adjustable Mounting Bolts into appropriate grooves on the bottom of the BREEZA WARM (US for United States & EU for European).
• b) Insert the Mounting Bolts through the toilet mounting holes.
• c) Adjust the seat by sliding it forward or backward along the track to obtain optimum position over the toilet bowl.
• d) Insert Rubber Washer, Plastic Washer and Plastic Wing-nut, from under the toilet, onto each Mounting Bolt and fasten until snug (repeat process on the other side).
• e) Use the Wrench to assist with tightening the Plastic Wing-nut if necessary.

Installing the BREEZAWARM (alternate)

Some toilet fixtures are designed with only top-side access. To install the BREEZA WARM onto these types of fixtures, an Alternate Mounting Kit is required.
To have a set of the Alternate Mounting Kit delivered to you, please contact Brondell.
Toll free number: (888) 542 – 3355

Opening / Closing POD Lid

1. To Open:
   a) Gently press down on the top edge.
   b) Push forward to remove.

2. To Close:
   a) Position POD Lid on top of the POD opening.
   b) Push POD Lid inward, listen for a “click” to ensure that POD Lid is securely closed.

Inserting Accessory Items

• a) Insert Breeza Filter cartridge in the designated location.
• b) Insert Breeza Vent cartridge in the designated location.
• 6. Pluging In the BREEZA WARM
• a) Plug into a grounded GFCI outlet.

Operation

Some of the features in the BREEZA WARM are designed to function only when the seat is occupied. The Power LED indicator (Green light) will remain on at all times to indicate the unit is ready.

Using the BREEZA WARM

• To Start : Gently sit on the seat. The seat sensor will automatically activate the Deodorizer function.
• To Stop: Move away from the seat. The Deodorizer function will remain on for an additional 90 seconds before automatically switching off.

Seat Temperature Setting

• To adjust seat temperature, gently press the button. Each time the ” button is pressed, a red LED will be lit, representing a higher level of temperature.
• Temp. adjustment cycle: off/ Low/ Mid/ High

Some of the features in the BREEZA WARM are designed to function only when the seat is occupied. The Power LED indicator (Green light) will remain on at all time to indicate the unit is ready.

Power Save Setting

• Do not sit on the seat while performing Power Save programming.

• To Activate – Press and hold the button for 5 seconds, until the LED’s change color (to Green) and begin to flash. While the LED’s are flashing, gently press the ., button to choose the desired Power Save duration.
  The 3 levels of Power Save durations are represented by the number of Green LED’s lit (please refer to the graphics to the right).
  Once the desired Power Save duration is chosen, wait for 5 seconds and allow the system to register the setting. Power Save mode will begin immediately thereafter.

• To Cancel – Enter into the Power Save setting mode as indicated above. Scroll through the button until all LED’s are flashing (Green). Wait 5 seconds for the system to register the setting. Power Save mode is now cancelled.

• To Interrupt – While the BREEZA WARM is in Power Save status, the Deodorizer system will automatically begin to function when the seat Is occupied.
  The Power Save system runs on a 24-hour cycle. Once Power Save duration is complete or has been interrupted, the BREEZA WARM will remain on until the next cycle of Power Save start time.

• During Power Save – While the BREEZA WARM is in Power Save status, the Seat Heat temperature will be off.

Caution

Seat Sensor

The seat sensor is designed to activate by the touch of bare skin.
Do not insert a seat cover over the BREEZA WARM seat.

Maintenance

Always unplug the BREEZA WARM before cleaning.

Seat Cleaning

Use a soft, damp cloth and mild cleanser (such as dish soap) to wipe down the seat and lid. NEVER scrub or use harsh, abrasive products to clean the BREEZA WARM.
For more thorough cleaning, you may
remove the BREEZA WARM. To release, unscrew and remove the Plastic Wing-nut, Plastic Washer and Rubber Washer that are against the bottom of the toilet mounting holes.
Perform the reverse operation when reinstalling the BREEZA WARM back onto the toilet.

Accessories Replacement

In order to maintain optimum performance, replace accessory items on a regular basis.
ITEM REPLACE
Breeza Vent Every month
Breeza Filter Every 6 months
To purchase additional accessories, please I visit: www.brondell.com

Troubleshooting

For other issues or questions please visit our website: www.brondell.com or contact Brondell Customer Service: 1-888-542-3355

Contact Information
Brondell, Inc.
P.O.Box 470085
San Francisco CA 94147-0085
Phone : 1-888-542-3355
E-mail : support@brondell.com
WEB : www.brondell.com

Warranty

5 Year Limited Warranty

Brondell warrants that all products (excluding consumable Items) shall be free from defects In material and workmanship under normal use and service.
WarTanties do not apply to products that are used for commercial, hospital or other non-residential application.

Residential Warranties for Breeza and Breeza WarmTollet Seat Products:

• 100% Coverage of all parts and labor for the first 2 years from original date of purchase
• 50% Coverage of all parts and labor for the years 3-5 from original date of purchase

Exclusions and Limitations

1. BRONDELL warrants its products to be free from manufacturing defects under normal use and service. This warranty is extended only to the ORIGINAL PURCHASER. This warranty does not apply to the Swash line of products.
2. BRONDELL’s obligations under this warranty are limited to repairs or replacement, at BRONDELL’s option, of products or parts found to be defective, provided that such products were properly installed and used in accordance with instructions. BRON DELL reserves the right to make such inspections as may be necessary in order to determine the cause of the defect. BRONDELL will not charge for labor or parts in connection with warranty repairs for the first 2 full years from date of purchase and will cover 50% of parts and labor in years 3-5.
3. BRON DELL Is not responsible for the cost of removal, return and/or relnstallation of products. This warranty does NOT apply to:
4. a) Damage or loss which occurs during shipment.
5. b) Damage or loss sustained through any natural or manmade causes beyond the control of BRONDELL, including but not limited to fire, earthquake, floods, etc.
6. c) Damage or loss resulting from sediments or foreign matter contained in a water system.
7. d) Damage or loss resulting from negligent or improper installation including installation of a unit in a harsh or hazardous environment.
8. e) Damage or loss resulting from removal, Improper repair, modification of the product, or Improper maintenance including damage caused by chlorine or chlorine related products.
9.  This warranty gives you specific legal rights. You may have other rights which vary from state to state.

THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY BRONDELL. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER. BRONDELL SHALL NOT BE RESPONSIBLE FOR LOSS OF USE OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL, FOR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE PURCHASER OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED ABOVE. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.

How to Obtain Service

To obtain repair service under this warranty, you must contact an authorized BRONDELL Service Center to obtain an RMA (Return Merchandise Authorization) number. Proof of purchase in the form of a copy of your original receipt must accompany the returned unit for the warranty to be valid. Take or ship the unit pre-paid to the closest Brondell authorized service center along with your RMA number and proof of purchase.
To obtain your RMA number and locate the BRONDELL Service Center location nearest you, call 1-888-542-3355.

Product Registration

To ensure you receive important warranty and product information, please register online at: http://www.brondell.com/warranty, within 10 days of purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>