ABAC G-810AL-BL Tool kit 8pcs User Guide

June 1, 2024
ABAC

ABAC G-810AL-BL Tool kit 8pcs

PNEUMATIC KIT

 |  |  | | |
---|---|---|---|---|---
 | Air pressure max,| bar| 4| 8| 8
 | Nozzle diameter,| [mm]| 1,5| 4.5|
 | Suction cup,| [ml]| 1000| 900|
 | Air consumption,| [l/s]| 2,5| 2| 1
 | Sound pressure level (LPA) acc. to. EN ISO 15744,| [dB(A]| 85| 92|
 | Spray pipe length,| [mm]| | 200| 400
 | weight,| [kg]| 0,6| 0.6|
 | Air inlet (BSP),| [inch]| 1/4” i| 1/4” i| 1/4” i

Paint spray gun

SAFETY WARNINGS

  • Never point the tool at yourself or other persons.
  • Do not use the tool improperly
  • Always disconnect the tool when not in use.
  • Keep the tool out of reach of children

WARNING! WHEN USING THE TOOL, MAKE SURE THAT THERE ARE NO NAKED FLAMES OR FLAMMABLE FUMES IN THE WORKING ENVIRONMENT, WEAR A PROTECTIVE MASK AND ALWAYS DISCONNECT THE TOOL WHEN NOT IN USE.

USE: Painting

OPERATING PROCEDURES
Connect the compressed air supply to connector C; before filling the tank, check that the spray gun is working (air is passing through the tool); mix the paint in a separate container and then pour it into tank F filling it to about 2/3 of its capacity. Position yourself at a distance of about 20-30 cm from the work surface, squeeze the trigger, and direct the jet towards it; move the spray gun parallel to the work surface, keeping it perpendicular to the surface.
You can adjust the intensity of the liquid flow with knob A and the width of the jet using knob B.

  • TUBE DIAMETER: 1/4″
  • TANK CAPACITY: 1 L

USEFUL TIPS
Check that the surface to be painted is perfectly clean and dry; to obtain an even coating, the paint stroke should begin before the trigger is squeezed and end after it is released; never stop at one particular point without releasing the trigger; always clean tank F and the tool thoroughly with appropriate solvents when the job is completed.

Spray gun – Instructions

SAFETY WARNINGS

  • Never point the tool at yourself or other persons.
  • Do not use the tool improperly
  • Always disconnect the tool when not in use.
  • Keep the tool out of reach of children

WARNING! WHEN USING THE TOOL, MAKE SURE THAT THERE ARE NO NAKED FLAMES OR FLAMMABLE FUMES IN THE WORKING ENVIRONMENT, WEAR A PROTECTIVE MASK AND ALWAYS DISCONNECT THE TOOL WHEN NOT IN USE.

OPERATING PROCEDURES

Before operating the equipment, put some oil drops in the air inlet opening (A) of the pneumatic tool. Choose the correct nozzle (C) and mount it onto the pipe. Fill the suction cup (D) with the working liquid and firmly tighten it to the spray gun. Depress the trigger (B) to use the tool. The user or the user’s employer shall assess the specific use that can be present as a result of each use. Never use the tool otherwise than the tool is designed for and as explained in this manual. Damages as a consequence of not following this manual, or caused by incorrect use or incorrect repairs, will never be covered by our warranty and we will have no responsibility for them. We reserve the right for technical improvements, without prior notification. This tool is designed for spraying oils, solvents, coatings, and liquids. If used otherwise a risk assessment has to be made by the employer/user.

MAINTENANCE

Disconnect the air supply during maintenance on the tool. Regularly clean and dry the filter in the system and the pneumatic tool air inlet opening. To avoid rust formation and to minimize wear, clean and lubricate the tool after each use. If you intend not to use the tool for a longer period, it has to be oiled. Please fill some droplets of resin and acid-free oil into the air inlet and let the tool run free for a couple of seconds. Maintain the tool at least yearly.

Tire inflator

SAFETY WARNINGS

  • Never point the tool at yourself or other persons.
  • Do not use the tool improperly
  • Always disconnect the tool when not in use.
  • Keep the tool out of reach of children

WARNING! WHEN USING THE TOOL, MAKE SURE THAT THERE ARE NO NAKED FLAMES OR FLAMMABLE FUMES IN THE WORKING ENVIRONMENT, WEAR A PROTECTIVE MASK AND ALWAYS DISCONNECT THE TOOL WHEN NOT IN USE.

OPERATING PROCEDURES
Connect the compressed air supply to fitting A. Connect the inflation fitting B to the valve of the wheel and check the pressure on gauge C. Press trigger D to inflate and keep checking the pressure on the gauge: if the pressure is too high, press trigger D half-way to restore the correct pressure. To avoid damage to the pressure gauge do not let the tire inflator fall on hard surfaces, to ensure a correct pressure value reading. Use one of the adapters included in the kit (E) to inflate bike inner tubes, balls, or other devices

MAINTENANCE

  • Disconnect the air supply during maintenance on the tool.
  • Regularly clean and dry the filter in the system and the pneumatic tool air inlet opening.
  • Lubricate any quick-disconnect coupling on the system to prevent jamming.
  • Drain condensation from the air filter and the compressor daily.
  • To avoid rust formation and to minimize wear, clean and lubricate the tool after each use.
  • Check the tool regularly for loose bolts/screws or parts.
  • In case of power loss: have the tool repaired.
  • Only trained and qualified engineers are allowed to adjust or repair the tool.

1pcs bike adapter, 1pcs ball needle, 1pcs universal needle for inflating devices

Product Information

Specifications

  • Model: Pneumatic Kit 2809900119
  • Tank Capacity : 1 liter
  • Air Pressure : 3-4 bar (43.5-58 psi)
  • Noise Level : 85 dB(A)
  • Tube Diameter : 1/4 inch
  • Weight : 0.6 kg

FAQ

Q: What is the tank capacity of the Pneumatic Kit?
A: The tank capacity is 1 liter.

Q: What is the recommended air pressure for painting?
A: The recommended air pressure for painting is 3-4 bar (43.5-58 psi).

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

ABAC User Manuals

Related Manuals